Abstract: The paper presents a numerical investigation on the
rapid gas decompression in pure nitrogen which is made by using the
one-dimensional (1D) and three-dimensional (3D) mathematical
models of transient compressible non-isothermal fluid flow in pipes.
A 1D transient mathematical model of compressible thermal multicomponent
fluid mixture flow in pipes is presented. The set of the
mass, momentum and enthalpy conservation equations for gas phase
is solved in the model. Thermo-physical properties of multicomponent
gas mixture are calculated by solving the Equation of
State (EOS) model. The Soave-Redlich-Kwong (SRK-EOS) model is
chosen. This model is successfully validated on the experimental data
[1] and shows a good agreement with measurements. A 3D transient
mathematical model of compressible thermal single-component gas
flow in pipes, which is built by using the CFD Fluent code (ANSYS),
is presented in the paper. The set of unsteady Reynolds-averaged
conservation equations for gas phase is solved. Thermo-physical
properties of single-component gas are calculated by solving the Real
Gas Equation of State (EOS) model. The simplest case of gas
decompression in pure nitrogen is simulated using both 1D and 3D
models. The ability of both models to simulate the process of rapid
decompression with a high order of agreement with each other is
tested. Both, 1D and 3D numerical results show a good agreement
between each other. The numerical investigation shows that 3D CFD
model is very helpful in order to validate 1D simulation results if the
experimental data is absent or limited.
Abstract: Combined therapy using Interferon and Ribavirin is the standard treatment in patients with chronic hepatitis C. However, the number of responders to this treatment is low, whereas its cost and side effects are high. Therefore, there is a clear need to predict patient’s response to the treatment based on clinical information to protect the patients from the bad drawbacks, Intolerable side effects and waste of money. Different machine learning techniques have been developed to fulfill this purpose. From these techniques are Associative Classification (AC) and Decision Tree (DT). The aim of this research is to compare the performance of these two techniques in the prediction of virological response to the standard treatment of HCV from clinical information. 200 patients treated with Interferon and Ribavirin; were analyzed using AC and DT. 150 cases had been used to train the classifiers and 50 cases had been used to test the classifiers. The experiment results showed that the two techniques had given acceptable results however the best accuracy for the AC reached 92% whereas for DT reached 80%.
Abstract: This paper focuses on systematic analysis and
controller design of the two-inertia STABILIZATION system,
considering the angular motion on a base body. This approach is
essential to the stabilization system to aim at a target under three or six
degrees of freedom base motion. Four controllers, such as
conventional PDF(Pseudo-Derivative Feedback) controller with
motor speed feedback, PDF controller with load speed feedback,
modified PDF controller with motor-load speed feedback and
feedforward controller added to modified PDF controller, are
suggested to improve reference tracking and disturbance rejection
performance. Characteristics and performance of each controller are
analyzed and validated by simulation in the case of the modified PDF
controller with and without a feedforward controller.
Abstract: In this paper we study the inverse eigenvalue problem for symmetric special matrices and introduce sufficient conditions for obtaining nonnegative matrices. We get the HROU algorithm from [1] and introduce some extension of this algorithm. If we have some eigenvectors and associated eigenvalues of a matrix, then by this extension we can find the symmetric matrix that its eigenvalue and eigenvectors are given. At last we study the special cases and get some remarkable results.
Abstract: Depressurization and pressurization streams in
industrial systems constitute a work exchange network (WEN). In this
paper, a novel graphical approach for targeting energy conservation
potential of a WEN is proposed. Through constructing the composite
work curves in the pressure-work diagram and assuming all of the
mechanical energy of the depressurization streams is recovered by
expanders, the maximum work target of a WEN can be determined via
the proposed targeting steps. A WEN in an ammonia production
process is used as a case study to illustrate the applicability of the
proposed graphical approach.
Abstract: In a representative democracy political parties
promote vital competition on different policy issues and play
essential roles by offering ideological alternatives. They also give
channels for citizens- participation in government decision-making
processes and they are significant conduits and interpreters of
information about government. This paper attempts to examine how
opposition political parties and rebel fronts emerged in Ethiopia, and
examines their present conditions. In this paper, selected case studies
of political parties and rebel fronts are included to highlight the status
and the role of opposition groups in the country in the three
successive administrations: Haile Selassie (1930-1974), Derg (1974-
1991), and EPRDF (1991-Present).
Abstract: The most common forensic activity is searching a hard
disk for string of data. Nowadays, investigators and analysts are
increasingly experiencing large, even terabyte sized data sets when
conducting digital investigations. Therefore consecutive searching can
take weeks to complete successfully. There are two primary search
methods: index-based search and bitwise search. Index-based
searching is very fast after the initial indexing but initial indexing
takes a long time. In this paper, we discuss a high speed bitwise search
model for large-scale digital forensic investigations. We used pattern
matching board, which is generally used for network security, to
search for string and complex regular expressions. Our results indicate
that in many cases, the use of pattern matching board can substantially
increase the performance of digital forensic search tools.
Abstract: The success of an electronic system in a System-on- Chip is highly dependent on the efficiency of its interconnection network, which is constructed from routers and channels (the routers move data across the channels between nodes). Since neither classical bus based nor point to point architectures can provide scalable solutions and satisfy the tight power and performance requirements of future applications, the Network-on-Chip (NoC) approach has recently been proposed as a promising solution. Indeed, in contrast to the traditional solutions, the NoC approach can provide large bandwidth with moderate area overhead. The selected topology of the components interconnects plays prime rule in the performance of NoC architecture as well as routing and switching techniques that can be used. In this paper, we present two generic NoC architectures that can be customized to the specific communication needs of an application in order to reduce the area with minimal degradation of the latency of the system. An experimental study is performed to compare these structures with basic NoC topologies represented by 2D mesh, Butterfly-Fat Tree (BFT) and SPIN. It is shown that Cluster mesh (CMesh) and MinRoot schemes achieves significant improvements in network latency and energy consumption with only negligible area overhead and complexity over existing architectures. In fact, in the case of basic NoC topologies, CMesh and MinRoot schemes provides substantial savings in area as well, because they requires fewer routers. The simulation results show that CMesh and MinRoot networks outperforms MESH, BFT and SPIN in main performance metrics.
Abstract: This article discusses the problem of estimating the
orientation of inclined ground on which a human subject stands based
on information provided by the vestibular system consisting of the
otolith and semicircular canals. It is assumed that body segments are
not necessarily aligned and thus forming an open kinematic chain.
The semicircular canals analogues to a technical gyrometer provide a
measure of the angular velocity whereas the otolith analogues to a
technical accelerometer provide a measure of the translational
acceleration. Two solutions are proposed and discussed. The first is
based on a stand-alone Kalman filter that optimally fuses the two
measurements based on their dynamic characteristics and their noise
properties. In this case, no body dynamic model is needed. In the
second solution, a central extended disturbance observer that
incorporates a body dynamic model (internal model) is employed.
The merits of both solutions are discussed and demonstrated by
experimental and simulation results.
Abstract: Constant amplitude fatigue crack growth (FCG) tests
were performed on dissimilar metal welded plates of Type 316L
Stainless Steel (SS) and IS 2062 Grade A Carbon steel (CS). The
plates were welded by TIG welding using SS E309 as electrode. FCG
tests were carried on the Side Edge Notch Tension (SENT)
specimens of 5 mm thickness, with crack initiator (notch) at base
metal region (BM), weld metal region (WM) and heat affected zones
(HAZ). The tests were performed at a test frequency of 10 Hz and at
load ratios (R) of 0.1 & 0.6. FCG rate was found to increase with
stress ratio for weld metals and base metals, where as in case of
HAZ, FCG rates were almost equal at high ΔK. FCG rate of HAZ of
stainless steel was found to be lowest at low and high ΔK. At
intermediate ΔK, WM showed the lowest FCG rate. CS showed
higher crack growth rate at all ΔK. However, the scatter band of data
was found to be narrow. Fracture toughness (Kc) was found to vary
in different locations of weldments. Kc was found lowest for the
weldment and highest for HAZ of stainless steel. A novel method of
characterizing the FCG behavior using an Infrared thermography
(IRT) camera was attempted. By monitoring the temperature rise at
the fast moving crack tip region, the amount of plastic deformation
was estimated.
Abstract: In this study, a novel approach of image embedding is introduced. The proposed method consists of three main steps. First, the edge of the image is detected using Sobel mask filters. Second, the least significant bit LSB of each pixel is used. Finally, a gray level connectivity is applied using a fuzzy approach and the ASCII code is used for information hiding. The prior bit of the LSB represents the edged image after gray level connectivity, and the remaining six bits represent the original image with very little difference in contrast. The proposed method embeds three images in one image and includes, as a special case of data embedding, information hiding, identifying and authenticating text embedded within the digital images. Image embedding method is considered to be one of the good compression methods, in terms of reserving memory space. Moreover, information hiding within digital image can be used for security information transfer. The creation and extraction of three embedded images, and hiding text information is discussed and illustrated, in the following sections.
Abstract: A Simultaneous Multithreading (SMT) Processor is
capable of executing instructions from multiple threads in the same
cycle. SMT in fact was introduced as a powerful architecture to
superscalar to increase the throughput of the processor.
Simultaneous Multithreading is a technique that permits multiple
instructions from multiple independent applications or threads to
compete limited resources each cycle. While the fetch unit has been
identified as one of the major bottlenecks of SMT architecture, several
fetch schemes were proposed by prior works to enhance the fetching
efficiency and overall performance.
In this paper, we propose a novel fetch policy called queue situation
identifier (QSI) which counts some kind of long latency instructions of
each thread each cycle then properly selects which threads to fetch
next cycle. Simulation results show that in best case our fetch policy
can achieve 30% on speedup and also can reduce the data cache level 1
miss rate.
Abstract: Visual information is very important in human perception
of surrounding world. Video is one of the most common ways to
capture visual information. The video capability has many benefits
and can be used in various applications. For the most part, the
video information is used to bring entertainment and help to relax,
moreover, it can improve the quality of life of deaf people. Visual
information is crucial for hearing impaired people, it allows them to
communicate personally, using the sign language; some parts of the
person being spoken to, are more important than others (e.g. hands,
face). Therefore, the information about visually relevant parts of the
image, allows us to design objective metric for this specific case. In
this paper, we present an example of an objective metric based on
human visual attention and detection of salient object in the observed
scene.
Abstract: The decision of information technology (IT) outsourcing requires close attention to the evaluation of supplier selection process because the selection decision involves conflicting multiple criteria and is replete with complex decision making problems. Selecting the most appropriate suppliers is considered an important strategic decision that may impact the performance of outsourcing engagements. The objective of this paper is to aid decision makers to evaluate and assess possible IT outsourcing suppliers. An axiomatic design based fuzzy group decision making is adopted to evaluate supplier alternatives. Finally, a case study is given to demonstrate the potential of the methodology. KeywordsIT outsourcing, Supplier selection, Multi-criteria decision making, Axiomatic design, Fuzzy logic.
Abstract: Biodiversity crisis is one of the many crises that
started at the turn of the millennia. Concrete form of expression is
still disputed, but there is a relatively high consensus regarding the
high rate of degradation and the urgent need for action. The strategy
of action outlines a strong economic component, together with the
recognition of market mechanisms as the most effective policies to
protect biodiversity. In this context, biodiversity and ecosystem
services are natural assets that play a key role in economic strategies
and technological development to promote development and
prosperity. Developing and strengthening policies for transition to an
economy based on efficient use of resources is the way forward.
To emphasize the co-viability specific to the connection economyecosystem
services, scientific approach aimed on one hand how to
implement policies for nature conservation and on the other hand, the
concepts underlying the economic expression of ecosystem services-
value, in the context of current technology. Following the analysis of
business opportunities associated with changes in ecosystem services
was concluded that development of market mechanisms for nature
conservation is a trend that is increasingly stronger individualized
within recent years. Although there are still many controversial issues
that have already given rise to an obvious bias, international
organizations and national governments have initiated and
implemented in cooperation or independently such mechanisms.
Consequently, they created the conditions for convergence between
private interests and social interests of nature conservation, so there
are opportunities for ongoing business development which leads,
among other things, the positive effects on biodiversity. Finally,
points out that markets fail to quantify the value of most ecosystem
services. Existing price signals reflect at best, only a proportion of the
total amount corresponding provision of food, water or fuel.
Abstract: In the present paper, Fatigue life assessment of an
anti-roll bar component of a passenger vehicle, is investigated by
ANSYS 11 software. A stress analysis is also carried out by the
finite element technique for the determination of highly stressed
regions on the bar. Anti-roll bar is a suspension element used at the
front, rear, or at both ends of a car that reduces body roll by resisting
any unequal vertical motion between the pair of wheels to which it is
connected. As a first stage, fatigue damage models proposed by some
well-known references and the corresponding assumptions are
discussed and some enhancements are proposed. Then, fracture
analysis of an anti-roll bar of an automobile is carried out. The
analysed type of the anti-roll bar is especially important as many
cases are reported about the fracture after a 100,000 km of travel
fatigue and fracture conditions. This paper demonstrates fatigue life
of an anti-roll bar and then evaluated by experimental analytically
results from other researcher.
Abstract: The problem of lot sizing, sequencing and scheduling
multiple products in flow line production systems has been studied
by several authors. Almost all of the researches in this area assumed
that setup times and costs are sequence –independent even though
sequence dependent setups are common in practice. In this paper we
present a new mixed integer non linear program (MINLP) and a
heuristic method to solve the problem in sequence dependent case.
Furthermore, a genetic algorithm has been developed which applies
this constructive heuristic to generate initial population. These two
proposed solution methods are compared on randomly generated
problems. Computational results show a clear superiority of our
proposed GA for majority of the test problems.
Abstract: Bus Rapid Transit (BRT) has emerged as a cost-effective transport system for urban mobility. However its ability to stimulate land development remains largely unexplored. The study makes use of qualitative (interview method) and quantitative analysis (questionnaire survey and longitudinal analysis of property data) to investigate land development impact resulting from BRT in Beijing, China. The empirical analysis suggests that BRT has a positive impact on the residential and commercial property attractiveness along the busway corridor. The statistical analysis suggests that accessibility advantage conferred by BRT is capitalized into higher property price. The average price of apartments adjacent to a BRT station has gained a relatively faster increase than those not served by the BRT system. The capitalization effect mostly occurs after the full operation of BRT, and is more evident over time and particularly observed in areas which previously lack alternative mobility opportunity.
Abstract: The Helmholtz equation often arises in the study of physical problems involving partial differential equation. Many researchers have proposed numerous methods to find the analytic or approximate solutions for the proposed problems. In this work, the exact analytical solutions of the Helmholtz equation in spherical polar coordinates are presented using the Nikiforov-Uvarov (NU) method. It is found that the solution of the angular eigenfunction can be expressed by the associated-Legendre polynomial and radial eigenfunctions are obtained in terms of the Laguerre polynomials. The special case for k=0, which corresponds to the Laplace equation is also presented.
Abstract: Parametric models have been quite popular for
studying human growth, particularly in relation to biological
parameters such as peak size velocity and age at peak size velocity.
Longitudinal data are generally considered to be vital for fittinga
parametric model to individual-specific data, and for studying the
distribution of these biological parameters in a human population.
However, cross-sectional data are easier to obtain than longitudinal
data. In this paper, we present a method of combining longitudinal
and cross-sectional data for the purpose of estimating the distribution
of the biological parameters. We demonstrate, through simulations in
the special case ofthePreece Baines model, how estimates based on
longitudinal data can be improved upon by harnessing the
information contained in cross-sectional data.We study the extent of
improvement for different mixes of the two types of data, and finally
illustrate the use of the method through data collected by the Indian
Statistical Institute.