Abstract: Crank shaft length, connecting rod length, crank angle, engine rpm, cylinder bore, mass of piston and compression ratio are the inputs that can control the performance of the slider crank mechanism and then its efficiency. Several combinations of these seven inputs are used and compared. The throughput engine torque predicted by the simulation is analyzed through two different regression models, with and without interaction terms, developed according to multi-linear regression using LU decomposition to solve system of algebraic equations. These models are validated. A regression model in seven inputs including their interaction terms lowered the polynomial degree from 3rd degree to 1st degree and suggested valid predictions and stable explanations.
Abstract: The aim of the paper is to explore the role of social marketing in changing the behavior of consumers on road safety, identify critical aspects and priority needs which impede the implementation of road safety program in Georgia. Given the goals of the study, a quantitative method was used to carry out interviews for primary data collection. This research identified the awareness level of road safety, legislation base, and marketing interventions to change behavior of drivers and pedestrians. During several years the non-governmental sector together with the local authorities and media have been very intensively working on the road safety issue in Georgia, but only seat-belts campaign should be considered rather successful. Despite achievements in this field, efficiency of road safety programs far from fulfillment and needs strong empowering.
Abstract: Many ophthalmologists can examine declines in visual sensitivity at arbitrary points on the retina using a precise perimetry device with a fundus camera function. However, the retinal layer causing the decline in visual sensitivity cannot be identified by this method. We studied an electroretinogram (ERG) function that can move the center of the multifocal hexagonal stimulus array in order to investigate cryptogenic diseases, such as macular dystrophy, acute zonal occult outer retinopathy, and multiple evanescent white dot syndrome. An electroretinographic optical system, specifically a perimetric optical system, was added to an experimental device carrying the same optical system as a fundus camera. We also added an infrared camera, a cold mirror, a halogen lamp, and a monitor. The software was generated to show the multifocal hexagonal stimulus array on the monitor using C++Builder XE8 and to move the center of the array up and down as well as back and forth. We used a multifunction I/O device and its design platform LabVIEW for data retrieval. The plate electrodes were used to measure electrodermal activities around the eyes. We used a multifocal hexagonal stimulus array with 37 elements in the software. The center of the multifocal hexagonal stimulus array could be adjusted to the same position as the examination target of the precise perimetry. We successfully added the moving ERG function to the experimental ophthalmologic device.
Abstract: The advancement in various concrete ingredients like plasticizers, additives and fibers, etc. has enabled concrete technologists to develop many viable varieties of special concretes in recent decades. Such various varieties of concrete have significant enhancement in green as well as hardened properties of concrete. A prudent selection of appropriate type of concrete can resolve many design and application issues in construction projects. This paper focuses on usage of self-compacting concrete, high early strength concrete, structural lightweight concrete, fiber reinforced concrete, high performance concrete and ultra-high strength concrete in the structures. The modified properties of strength at various ages, flowability, porosity, equilibrium density, flexural strength, elasticity, permeability etc. need to be carefully studied and incorporated into the design of the structures. The paper demonstrates various mixture combinations and the concrete properties that can be leveraged. The selection of such products based on the end use of structures has been proposed in order to efficiently utilize the modified characteristics of these concrete varieties. The study involves mapping the characteristics with benefits and savings for the structure from design perspective. Self-compacting concrete in the structure is characterized by high shuttering loads, better finish, and feasibility of closer reinforcement spacing. The structural design procedures can be modified to specify higher formwork strength, height of vertical members, cover reduction and increased ductility. The transverse reinforcement can be spaced at closer intervals compared to regular structural concrete. It allows structural lightweight concrete structures to be designed for reduced dead load, increased insulation properties. Member dimensions and steel requirement can be reduced proportionate to about 25 to 35 percent reduction in the dead load due to self-weight of concrete. Steel fiber reinforced concrete can be used to design grade slabs without primary reinforcement because of 70 to 100 percent higher tensile strength. The design procedures incorporate reduction in thickness and joint spacing. High performance concrete employs increase in the life of the structures by improvement in paste characteristics and durability by incorporating supplementary cementitious materials. Often, these are also designed for slower heat generation in the initial phase of hydration. The structural designer can incorporate the slow development of strength in the design and specify 56 or 90 days strength requirement. For designing high rise building structures, creep and elasticity properties of such concrete also need to be considered. Lastly, certain structures require a performance under loading conditions much earlier than final maturity of concrete. High early strength concrete has been designed to cater to a variety of usages at various ages as early as 8 to 12 hours. Therefore, an understanding of concrete performance specifications for special concrete is a definite door towards a superior structural design approach.
Abstract: Due to the numerous advantages of steel corrugated
web girders, its application field is growing for bridges as well as for
buildings. The global stability behavior of such girders is
significantly larger than those of conventional I-girders with flat web,
thus the application of the structural steel material can be
significantly reduced. Design codes and specifications do not provide
clear and complete rules or recommendations for the determination of
the lateral torsional buckling (LTB) resistance of corrugated web
girders. Therefore, the authors made a thorough investigation
regarding the LTB resistance of the corrugated web girders. Finite
element (FE) simulations have been performed to develop new
design formulas for the determination of the LTB resistance of
trapezoidally corrugated web girders. FE model is developed
considering geometrical and material nonlinear analysis using
equivalent geometric imperfections (GMNI analysis). The equivalent
geometric imperfections involve the initial geometric imperfections
and residual stresses coming from rolling, welding and flame cutting.
Imperfection sensitivity analysis was performed to determine the
necessary magnitudes regarding only the first eigenmodes shape
imperfections. By the help of the validated FE model, an extended
parametric study is carried out to investigate the LTB resistance for
different trapezoidal corrugation profiles. First, the critical moment of
a specific girder was calculated by FE model. The critical moments
from the FE calculations are compared to the previous analytical
calculation proposals. Then, nonlinear analysis was carried out to
determine the ultimate resistance. Due to the numerical
investigations, new proposals are developed for the determination of
the LTB resistance of trapezoidally corrugated web girders through a
modification factor on the design method related to the conventional
flat web girders.
Abstract: The latent heat thermal energy storage system is a
thrust area of research due to exuberant thermal energy storage
potential. The thermal performance of PCM is significantly
augmented by installation of the high thermal conductivity fins. The
objective of the present study is to obtain optimum size and location
of the fins to enhance diffusion heat transfer without altering overall
melting time. Hence, the constructal theory is employed to eliminate,
resize, and re-position the fins. A numerical code based on conjugate
heat transfer coupled enthalpy porosity approached is developed to
solve Navier-Stoke and energy equation.The numerical results show
that the constructal fin design has enhanced the thermal performance
along with the increase in the overall volume of PCM when
compared to conventional. The overall volume of PCM is found to be
increased by half of total of volume of fins. The elimination and repositioning
the fins at high temperature gradient from low
temperature gradient is found to be vital.
Abstract: The discussion about elements of cultural heritage and
their relevance among the ancient villages is comparably insufficient.
The protection work is strongly influenced by touristic development
and cultural gimmick, resulting in low protection efficiency and many
omissions. Historical villages as the cultural settlement patterns bear a
large number of heritage relics. They were regionally scattered with a
clear characteristic of gathering. First of all, this study proposes the
association and similarities of the forming mechanism between four
historic cultural villages in Mian Mountain. Secondly, the study
reveals that these villages own the strategic pass, underground
passage, and the mountain barrier. Thirdly, based on the differentiated
characteristics of villages’ space, the study discusses about the
integrated conservation from three levels: the regional heritage
conservation, the cultural line shaping, and the featured brand
building.
Abstract: In this paper, an (irregular) case relating to base circle, root circle, and pressure angle has been discussed and a computer programme has been developed to simulate and plot spur gear tooth profile, including involute and trochoid curves based on the formulation of rack cutter using different values of pressure angle and profile shift factor and it gave the values of all important geometric parameters. The results showed the flexibility of this approach and versatility of the programme to draw many different cases of spur gear teeth of any module, pressure angle, profile shift factor, number of teeth and rack cutter tip radius. The procedure developed can be extended to produce finite element models of heretofore intractable geometrical forms, to exploring fabrication of nonstandard tooth forms also. Finite elements model of these irregular cases have been built using above programme, and modal analysis has been done using ANSYS software, and natural frequencies of these selected cases have been obtained and discussed.
Abstract: The purpose of the present research is to equate two
test forms as part of a study to evaluate the educational effectiveness
of the ARTé: Mecenas art history learning game. The researcher
applied Item Response Theory (IRT) procedures to calculate item,
test, and mean-sigma equating parameters. With the sample size
n=134, test parameters indicated “good” model fit but low Test
Information Functions and more acute than expected equating
parameters. Therefore, the researcher applied equipercentile equating
and linear equating to raw scores and compared the equated form
parameters and effect sizes from each method. Item scaling in IRT
enables the researcher to select a subset of well-discriminating items.
The mean-sigma step produces a mean-slope adjustment from the
anchor items, which was used to scale the score on the new form
(Form R) to the reference form (Form Q) scale. In equipercentile
equating, scores are adjusted to align the proportion of scores in each
quintile segment. Linear equating produces a mean-slope adjustment,
which was applied to all core items on the new form. The study
followed a quasi-experimental design with purposeful sampling of
students enrolled in a college level art history course (n=134) and
counterbalancing design to distribute both forms on the pre- and posttests.
The Experimental Group (n=82) was asked to play ARTé:
Mecenas online and complete Level 4 of the game within a two-week
period; 37 participants completed Level 4. Over the same period, the
Control Group (n=52) did not play the game. The researcher
examined between group differences from post-test scores on test
Form Q and Form R by full-factorial Two-Way ANOVA. The raw
score analysis indicated a 1.29% direct effect of form, which was
statistically non-significant but may be practically significant. The
researcher repeated the between group differences analysis with all
three equating methods. For the IRT mean-sigma adjusted scores,
form had a direct effect of 8.39%. Mean-sigma equating with a small
sample may have resulted in inaccurate equating parameters.
Equipercentile equating aligned test means and standard deviations,
but resultant skewness and kurtosis worsened compared to raw score
parameters. Form had a 3.18% direct effect. Linear equating
produced the lowest Form effect, approaching 0%. Using linearly
equated scores, the researcher conducted an ANCOVA to examine
the effect size in terms of prior knowledge. The between group effect
size for the Control Group versus Experimental Group participants
who completed the game was 14.39% with a 4.77% effect size
attributed to pre-test score. Playing and completing the game
increased art history knowledge, and individuals with low prior
knowledge tended to gain more from pre- to post test. Ultimately,
researchers should approach test equating based on their theoretical
stance on Classical Test Theory and IRT and the respective assumptions. Regardless of the approach or method, test equating
requires a representative sample of sufficient size. With small sample
sizes, the application of a range of equating approaches can expose
item and test features for review, inform interpretation, and identify
paths for improving instruments for future study.
Abstract: Tire noise has a significant impact on ride quality
and vehicle interior comfort, even at low frequency. Reduction of
tire noise is especially important due to strict state and federal
environmental regulations. The primary sources of tire noise are the
low frequency structure-borne noise and the noise that originates from
the release of trapped air between the tire tread and road surface
during each revolution of the tire. The frequency response of the tire
changes at low and high frequency. At low frequency, the tension
and bending moment become dominant, while the internal structure
and local deformation become dominant at higher frequencies. Here,
we analyze tire response in terms of deformation and rolling velocity
at low revolution frequency. An Abaqus FEA finite element model
is used to calculate the static and dynamic response of a rolling tire
under different rolling conditions. The natural frequencies and mode
shapes of a deformed tire are calculated with the FEA package where
the subspace-based steady state dynamic analysis calculates dynamic
response of tire subjected to harmonic excitation. The analysis was
conducted on the dynamic response at the road (contact point of tire
and road surface) and side nodes of a static and rolling tire when
the tire was excited with 200 N vertical load for a frequency ranging
from 20 to 200 Hz. The results show that frequency has little effect on
tire deformation up to 80 Hz. But between 80 and 200 Hz, the radial
and lateral components of displacement of the road and side nodes
exhibited significant oscillation. For the static analysis, the fluctuation
was sharp and frequent and decreased with frequency. In contrast, the
fluctuation was periodic in nature for the dynamic response of the
rolling tire. In addition to the dynamic analysis, a steady state rolling
analysis was also performed on the tire traveling at ground velocity
with a constant angular motion. The purpose of the computation
was to demonstrate the effect of rotating motion on deformation and
rolling velocity with respect to a fixed Newtonian reference point.
The analysis showed a significant variation in deformation and rolling
velocity due to centrifugal and Coriolis acceleration with respect to
a fixed Newtonian point on ground.
Abstract: Bullet penetration in steel plate is investigated with
the help of three-dimensional, non-linear, transient, dynamic, finite
elements analysis using explicit time integration code LSDYNA. The
effect of large strain, strain-rate and temperature at very high velocity
regime was studied from number of simulations of semi-spherical
nose shape bullet penetration through single layered circular plate
with 2 mm thickness at impact velocities of 500, 1000, and 1500 m/s
with the help of Johnson Cook material model. Mie-Gruneisen
equation of state is used in conjunction with Johnson Cook material
model to determine pressure-volume relationship at various points of
interests. Two material models viz. Plastic-Kinematic and Johnson-
Cook resulted in different deformation patterns in steel plate. It is
observed from the simulation results that the velocity drop and loss of
kinetic energy occurred very quickly up to perforation of plate, after
that the change in velocity and changes in kinetic energy are
negligibly small. The physics behind this kind of behaviour is
presented in the paper.
Abstract: In this paper, the velocity potential and stream
function of capture zone for a well field in an aquifer bounded by two
parallel streams with or without a uniform regional flow of any
directions are presented. The well field includes any number of
extraction or injection wells or a combination of both types with any
pumping rates. To delineate the capture envelope, the potential and
streamlines equations are derived by conformal mapping method.
This method can help us to release constrains of other methods. The
equations can be applied as useful tools to design in-situ groundwater
remediation systems, to evaluate the surface–subsurface water
interaction and to manage the water resources.
Abstract: Background: Islands in the Mediterranean region offer
opportunities for various industries to take advantage of the
facilitation and use of versatile floating structures in coastal areas. In
the context of dense land use, marine structures can contribute to
ensure both terrestrial and marine resource sustainability. Objective:
The aim of this paper is to present and critically discuss an array of
issues that characterize the design process of a floating structure for
coastal areas and to present the challenges and opportunities of
providing such multifunctional and versatile structures around the
Maltese coastline. Research Design: A three-tier research design
commenced with a systematic literature review. Semi-structured
interviews with stakeholders including a naval architect, a marine
engineer and civil designers were conducted. A second stage
preceded a focus group with stakeholders in design and construction
of marine lightweight structures. The three tier research design
ensured triangulation of issues. All phases of the study were
governed by research ethics. Findings: Findings were grouped into
three main themes: excellence, impact and implementation. These
included design considerations, applications and potential impacts on
local industry. Literature for the design and construction of marine
structures in the Maltese Islands presented multiple gaps in the
application of marine structures for local industries. Weather
conditions, depth of sea bed and wave actions presented limitations
on the design capabilities of the structure. Conclusion: Water
structures offer great potential and conclusions demonstrate the
applicability of such designs for Maltese waters. There is still no such
provision within Maltese coastal areas for multi-purpose use. The
introduction of such facilities presents a range of benefits for visiting
tourists and locals thereby offering wide range of services to tourism
and marine industry. Costs for construction and adverse weather
conditions were amongst the main limitations that shaped design
capacities of the water structures.
Abstract: The Extended Enterprise Resource Planning (ERPII)
system usually requires massive amounts of storage space, powerful
servers, and large upfront and ongoing investments to purchase and
manage the software and the related hardware which are not
affordable for organizations. In recent decades, organizations prefer
to adapt their business structures with new technologies for
remaining competitive in the world economy. Therefore, cloud
computing (which is one of the tools of information technology (IT))
is a modern system that reveals the next-generation application
architecture. Also, cloud computing has had some advantages that
reduce costs in many ways such as: lower upfront costs for all
computing infrastructure and lower cost of maintaining and
supporting. On the other hand, traditional ERPII is not responding for
huge amounts of data and relations between the organizations. In this
study, based on a literature study, ERPII is investigated in the context
of cloud computing where the organizations operate more efficiently.
Also, ERPII conditions have a response to needs of organizations in
large amounts of data and relations between the organizations.
Abstract: The psychological present has an actual extension.
When a sequence of instantaneous stimuli falls in this short interval
of time, observers perceive a compresence of events in succession
and the temporal order depends on the qualitative relationships
between the perceptual properties of the events. Two experiments
were carried out to study the influence of perceptual grouping, with
and without temporal displacement, on the duration of auditory
sequences. The psychophysical method of adjustment was adopted.
The first experiment investigated the effect of temporal displacement
of a white noise on sequence duration. The second experiment
investigated the effect of temporal displacement, along the pitch
dimension, on temporal shortening of sequence. The results suggest
that the temporal order of sounds, in the case of temporal
displacement, is organized along the pitch dimension.
Abstract: Safety and security concerns play a key role during
the design of civil UAs (aircraft controlled by a pilot who is not onboard
it) by the producers and the offer of different services by the
operators. At present, European countries have fragmented
regulations about the manufacture and use of civil drones, therefore
the European institutions are trying to approach all these regulations
into a common one. In this sense, not only law but also ethics can
give guidelines to the industry in order to obtain better reports from
their clients. With our results, we would like to give advice to the
European industry, as well as give new insights to the academia and
policymakers.
Abstract: Minimizing the weight in flexible structures means
reducing material and costs as well. However, these structures could
become prone to vibrations. Attenuating these vibrations has become
a pivotal engineering problem that shifted the focus of many research
endeavors. One technique to do that is to design and implement
an active control system. This system is mainly composed of a
vibrating structure, a sensor to perceive the vibrations, an actuator
to counteract the influence of disturbances, and finally a controller to
generate the appropriate control signals. In this work, two different
techniques are explored to create two different mathematical models
of an active control system. The first model is a finite element model
with a reduced number of nodes and it is called a super-element.
The second model is in the form of state-space representation, i.e.
a set of partial differential equations. The damping coefficients are
calculated and incorporated into both models. The effectiveness of
these models is demonstrated when the system is excited by its first
natural frequency and an active control strategy is developed and
implemented to attenuate the resulting vibrations. Results from both
modeling techniques are presented and compared.
Abstract: An increasing degree of automation in air traffic will also change the role of the air traffic controller (ATCO). ATCOs will fulfill significantly more monitoring tasks compared to today. However, this rather passive role may lead to Out-Of-The-Loop (OOTL) effects comprising vigilance decrement and less situation awareness. The project MINIMA (Mitigating Negative Impacts of Monitoring high levels of Automation) has conceived a system to control and mitigate such OOTL phenomena. In order to demonstrate the MINIMA concept, an experimental simulation set-up has been designed. This set-up consists of two parts: 1) a Task Environment (TE) comprising a Terminal Maneuvering Area (TMA) simulator as well as 2) a Vigilance and Attention Controller (VAC) based on neurophysiological data recording such as electroencephalography (EEG) and eye-tracking devices. The current vigilance level and the attention focus of the controller are measured during the ATCO’s active work in front of the human machine interface (HMI). The derived vigilance level and attention trigger adaptive automation functionalities in the TE to avoid OOTL effects. This paper describes the full-scale experimental set-up and the component development work towards it. Hence, it encompasses a pre-test whose results influenced the development of the VAC as well as the functionalities of the final TE and the two VAC’s sub-components.
Abstract: A crucial component to the success of any financial advising relationship is for the financial professional to understand the perceptions, preferences and thought-processes carried by the financial clients they serve. Armed with this information, financial professionals are more quickly able to understand how they can tailor their approach to best match the individual preferences and needs of each personal investor. Our research explores the use of a quantitative assessment tool in the financial services industry to assist in the identification of the personal investor’s consumer behaviors, especially in terms of financial risk tolerance, as it relates to their financial decision making. Through this process, the Unitifi Consumer Insight Tool (UCIT) was created and refined to capture and categorize personal investor financial behavioral categories and the financial personality tendencies of individuals prior to the initiation of a financial advisement relationship. This paper discusses the use of this tool to place individuals in one of four behavior-based financial risk tolerance categories. Our discoveries and research were aided through administration of a web-based survey to a group of over 1,000 individuals. Our findings indicate that it is possible to use a quantitative assessment tool to assist in predicting the behavioral tendencies of personal consumers when faced with consumer financial risk and decisions.
Abstract: The rapid progress of technology in today's competitive conditions has also accelerated companies' technology development activities. As a result, companies are paying more attention to R&D studies and are beginning to allocate a larger share to R&D projects. A more systematic, comprehensive, target-oriented implementation of R&D studies is crucial for the company to achieve successful results. As a consequence, Technology Roadmap (TRM) is gaining importance as a management tool. It has critical prospects for achieving medium and long term success as it contains decisions about past business, future plans, technological infrastructure. When studies on TRM are examined, projects to be placed on the roadmap are selected by many different methods. Generally preferred methods are based on multi-criteria decision making methods. Management of selected projects becomes an important point after the selection phase of the projects. At this stage, TRM are used. TRM can be created in many different ways so that each institution can prepare its own Technology Roadmap according to their strategic plan. Depending on the intended use, there can be TRM with different layers at different sizes. In the evaluation phase of the R&D projects and in the creation of the TRM, HAVELSAN, Turkey's largest defense company in the software field, carries out this process with great care and diligence. At the beginning, suggested R&D projects are evaluated by the Technology Management Board (TMB) of HAVELSAN in accordance with the company's resources, objectives, and targets. These projects are presented to the TMB periodically for evaluation within the framework of certain criteria by board members. After the necessary steps have been passed, the approved projects are added to the time-based TRM, which is composed of four layers as market, product, project and technology. The use of a four-layered roadmap provides a clearer understanding and visualization of company strategy and objectives. This study demonstrates the benefits of using TRM, four-layered Technology Roadmapping and the possibilities for the institutions in the defense industry.