Abstract: In this paper, we propose a direct method based on the
real Schur factorization for solving the projected Sylvester equation
with relatively small size. The algebraic formula of the solution of
the projected continuous-time Sylvester equation is presented. The
computational cost of the direct method is estimated. Numerical
experiments show that this direct method has high accuracy.
Abstract: Vehicle which are turning or maneuvering at high speeds
are susceptible to sliding and subsequently deviate from desired path. In
this paper the dynamics governing the Yaw/Roll behavior of a vehicle
has been simulated. Two different simulations have been used one for
the real vehicle, for which a fuzzy controller is designed to increase its
directional stability property. The other simulation is for a hypothetical
vehicle with much higher tire cornering stiffness which is capable of
developing the required lateral forces at the tire-ground patch contact to
attain the desired lateral acceleration for the vehicle to follow the
desired path without slippage. This simulation model is our reference
model.
The logic for keeping the vehicle on the desired track in the cornering
or maneuvering state is to have some braking forces on the inner or
outer tires based on the direction of vehicle deviation from the desired
path. The inputs to our vehicle simulation model is steer angle δ and
vehicle velocity V , and the outputs can be any kinematical parameters
like yaw rate, yaw acceleration, side slip angle, rate of side slip angle
and so on. The proposed fuzzy controller is a feed forward controller.
This controller has two inputs which are steer angle δ and vehicle
velocity V, and the output of the controller is the correcting moment M,
which guides the vehicle back to the desired track. To develop the
membership functions for the controller inputs and output and the fuzzy
rules, the vehicle simulation has been run for 1000 times and the
correcting moment have been determined by trial and error. Results of
the vehicle simulation with fuzzy controller are very promising
and show the vehicle performance is enhanced greatly over the
vehicle without the controller. In fact the vehicle performance
with the controller is very near the performance of the reference
ideal model.
Abstract: In areas of low to moderate seismicity many building contents and equipment are not positively fixed to the floor or tied to adjacent walls. Under seismic induced horizontal vibration, such contents and equipment can suffer from damage by either overturning or impact associated with rocking. This paper focuses on the estimation of shock on typical contents and equipment due to rocking. A simplified analytical model is outlined that can be used to estimate the maximum acceleration on a rocking object given its basic geometric and mechanical properties. The developed model was validated against experimental results. The experimental results revealed that the maximum shock acceleration can be underestimated if the static stiffness of the materials at the interface between the rocking object and floor is used rather than the dynamic stiffness. Excellent agreement between the model and experimental results was found when the dynamic stiffness for the interface material was used, which was found to be generally much higher than corresponding static stiffness under different investigated boundary conditions of the cushion. The proposed model can be a beneficial tool in performing a rapid assessment of shock sensitive components considered for possible seismic rectification.
Abstract: This paper provides the design steps of a robust Linear
Matrix Inequality (LMI) based iterative multivariable PID controller
whose duty is to drive a sample power system that comprises a
synchronous generator connected to a large network via a step-up
transformer and a transmission line. The generator is equipped with
two control-loops, namely, the speed/power (governor) and voltage
(exciter). Both loops are lumped in one where the error in the
terminal voltage and output active power represent the controller
inputs and the generator-exciter voltage and governor-valve position
represent its outputs. Multivariable PID is considered here because of
its wide use in the industry, simple structure and easy
implementation. It is also preferred in plants of higher order that
cannot be reduced to lower ones. To improve its robustness to
variation in the controlled variables, H∞-norm of the system transfer
function is used. To show the effectiveness of the controller, divers
tests, namely, step/tracking in the controlled variables, and variation
in plant parameters, are applied. A comparative study between the
proposed controller and a robust H∞ LMI-based output feedback is
given by its robustness to disturbance rejection. From the simulation
results, the iterative multivariable PID shows superiority.
Abstract: The paper provides a literature review of the STEPNC
compliant research around the world. The first part of this paper
focuses on projects based on STEP compliance followed by research
and development in this area based on machining operations. Review
the literature relating to relevant STEP standards and application in
the area of turning centers. This research will review the various
research work, carried out from the evolution of STEP-NC of the
CNC manufacturing activities. The paper concludes with discussion
of the applications in this particular area.
Abstract: In this paper, a novel method for recognition of musical
instruments in a polyphonic music is presented by using an
embedded hidden Markov model (EHMM). EHMM is a doubly
embedded HMM structure where each state of the external HMM
is an independent HMM. The classification is accomplished for
two different internal HMM structures where GMMs are used as
likelihood estimators for the internal HMMs. The results are compared
to those achieved by an artificial neural network with two
hidden layers. Appropriate classification accuracies were achieved
both for solo instrument performance and instrument combinations
which demonstrates that the new approach outperforms the similar
classification methods by means of the dynamic of the signal.
Abstract: Losses reduction initiatives in distribution systems
have been activated due to the increasing cost of supplying
electricity, the shortage in fuel with ever-increasing cost to produce
more power, and the global warming concerns. These initiatives have
been introduced to the utilities in shape of incentives and penalties.
Recently, the electricity distribution companies in Oman have been
incentivized to reduce the distribution technical and non-technical
losses with an equal annual reduction rate for 6 years. In this paper,
different techniques for losses reduction in Mazoon Electricity
Company (MZEC) are addressed. In this company, high numbers of
substation and feeders were found to be non-compliant with the
Distribution System Security Standard (DSSS). Therefore, 33
projects have been suggested to bring non-complying 29 substations
and 28 feeders to meet the planed criteria and to comply with the
DSSS. The largest part of MZEC-s network (South Batinah region)
was modeled by ETAP software package. The model has been
extended to implement the proposed projects and to examine their
effects on losses reduction. Simulation results have shown that the
implementation of these projects leads to a significant improvement
in voltage profile, and reduction in the active and the reactive power
losses. Finally, the economical analysis has revealed that the
implementation of the proposed projects in MZEC leads to an annual
saving of about US$ 5 million.
Abstract: Many researchers are working on information hiding
techniques using different ideas and areas to hide their secrete data.
This paper introduces a robust technique of hiding secret data in
image based on LSB insertion and RSA encryption technique. The
key of the proposed technique is to encrypt the secret data. Then the
encrypted data will be converted into a bit stream and divided it into
number of segments. However, the cover image will also be divided
into the same number of segments. Each segment of data will be
compared with each segment of image to find the best match
segment, in order to create a new random sequence of segments to be
inserted then in a cover image. Experimental results show that the
proposed technique has a high security level and produced better
stego-image quality.
Abstract: This paper mainly studies the analyses of parameters
in the intersection collision avoidance (ICA) system based on the radar
sensors. The parameters include the positioning errors, the repeat
period of the radar sensor, the conditions of potential collisions of two
cross-path vehicles, etc. The analyses of the parameters can provide
the requirements, limitations, or specifications of this ICA system. In
these analyses, the positioning errors will be increased as the measured
vehicle approach the intersection. In addition, it is not necessary to
implement the radar sensor in higher position since the positioning
sensitivities become serious as the height of the radar sensor increases.
A concept of the safety buffer distances for front and rear of the
measured vehicle is also proposed. The conditions for potential
collisions of two cross-path vehicles are also presented to facilitate the
computation algorithm.
Abstract: Internal controls of accounting are an essential
business function for a growth-oriented organization, and include the
elements of risk assessment, information communications and even
employees' roles and responsibilities. Internal controls of accounting
systems are designed to protect a company from fraud, abuse and
inaccurate data recording and help organizations keep track of
essential financial activities. Internal controls of accounting provide a
streamlined solution for organizing all accounting procedures and
ensuring that the accounting cycle is completed consistently and
successfully. Implementing a formal Accounting Procedures Manual
for the organization allows the financial department to facilitate
several processes and maintain rigorous standards. Internal controls
also allow organizations to keep detailed records, manage and
organize important financial transactions and set a high standard for
the organization's financial management structure and protocols. A
well-implemented system also reduces the risk of accounting errors
and abuse. A well-implemented controls system allows a company's
financial managers to regulate and streamline all functions of the
accounting department. Internal controls of accounting can be set up
for every area to track deposits, monitor check handling, keep track
of creditor accounts, and even assess budgets and financial statements
on an ongoing basis. Setting up an effective accounting system to
monitor accounting reports, analyze records and protect sensitive
financial information also can help a company set clear goals and
make accurate projections. Creating efficient accounting processes
allows an organization to set specific policies and protocols on
accounting procedures, and reach its financial objectives on a regular
basis. Internal accounting controls can help keep track of such areas
as cash-receipt recording, payroll management, appropriate recording
of grants and gifts, cash disbursements by authorized personnel, and
the recording of assets. These systems also can take into account any
government regulations and requirements for financial reporting.
Abstract: The effect of wood vinegar, entomopathogenic
nematodes ((Steinernema thailandensis n. sp.) and fermented organic
substances from four plants such as: Derris elliptica Roxb, Stemona
tuberosa Lour, Tinospora crispa Mier and Azadirachta indica J. were
tested on the five varieties of sweetpotato with potential for
bioethanol production ie. Taiwan, China, PROC No.65-16, Phichit
166-5, and Phichit 129-6. The experimental plots were located at
Faculty of Agriculture, Natural Resources and Environment,
Naresuan University, Phitsanulok, Thailand. The aim of this study
was to compare the efficiency of the five treatments for growth, yield
and insect infestation on the five varieties of sweetpotato. Treatment
with entomopathogenic nematodes gave the highest average weight
of sweetpotato tubers (1.3 kg/tuber), followed by wood vinegar,
fermented organic substances and mixed treatment with yields of
0.88, 0.46 and 0.43 kg/tuber, respectively. Also the
entomopathogenic nematode treatment gave significantly higher
average width and length of sweet potato (9.82 cm and 9.45 cm,
respectively). Additionally, the entomopathogenic nematode
provided the best control of insect infestation on sweetpotato leaves
and tubers. Comparison among the varieties of sweetpotato, PROC
NO.65-16 showed the highest weight and length. However, Phichit
129-6 gave significantly higher weight of 0.94 kg/tuber. Lastly, the
lowest sweet potato weevil infestation on leaves and tubers occurred
on Taiwan and Phichit 129-6.
Abstract: Organizational culture fosters innovation, and
innovation is the main engine to be sustained within the uncertainty
market. Like other countries, the construction industry significantly
contributes to the economy, society and technology of Malaysia, yet,
innovation is still considered slow compared to other industries such
as manufacturing. Given the important role of an architect as the key
player and the contributor of new ideas in the construction industry,
there is a call to identify the issue and improve the current situation
by focusing on the architectural firms. In addition, the existing
studies tend to focus only on a few dimensions of organizational
culture and very few studies consider whether innovation is being
generated or adopted. Hence, the present research tends to fill in the
gap by identifying the organizational cultures that foster or hinder
innovation generation and/or innovation adoption, and propose a
model of organizational culture and innovation generation and/or
adoption.
Abstract: In this paper, low end Digital Signal Processors (DSPs)
are applied to accelerate integer neural networks. The use of DSPs
to accelerate neural networks has been a topic of study for some
time, and has demonstrated significant performance improvements.
Recently, work has been done on integer only neural networks, which
greatly reduces hardware requirements, and thus allows for cheaper
hardware implementation. DSPs with Arithmetic Logic Units (ALUs)
that support floating or fixed point arithmetic are generally more
expensive than their integer only counterparts due to increased circuit
complexity. However if the need for floating or fixed point math
operation can be removed, then simpler, lower cost DSPs can be
used. To achieve this, an integer only neural network is created in
this paper, which is then accelerated by using DSP instructions to
improve performance.
Abstract: SEMG (Surface Electromyogram) is one of the
bio-signals and is generated from the muscle. And there are many
research results that use forearm EMG to detect hand motions. In this
paper, we will talk about our developed the robot hand system that can
control grasping power by SEMG. In our system, we suppose that
muscle power is proportional to the amplitude of SEMG. The power is
estimated and the grip power of a robot hand is able to be controlled
using estimated muscle power in our system. In addition, to perform a
more precise control can be considered to build a closed loop feedback
system as an object to a subject to pressure from the edge of hand. Our
objectives of this study are the development of a method that makes
perfect detection of the hand grip force possible using SEMG patterns,
and applying this method to the man-machine interface.
Abstract: There are increasingly plagiarism offences for
students in higher education in the digital educational world. On the
other hand, various and competitive online assessment and
plagiarism detection tools are available in the market. Taking the
University of Glamorgan as a case study, this paper describes and
introduces an institutional journey on electronic plagiarism detection
to inform the initial experience of an innovative tool and method
which could be further explored in the future research. The
comparative study and system workflow for e-plagiarism detection
tool are discussed. Benefits for both academics and students are also
presented. Electronic plagiarism detection tools brought great
benefits to both academics and students in Glamorgan. On the other
hand, the debates raised in such initial experience are discussed.
Abstract: The goal of this research is discovering the
determinants of the success or failure of external cooperation in small
and medium enterprises (SMEs). For this, a survey was given to 190
SMEs that experienced external cooperation within the last 3 years. A
logistic regression model was used to derive organizational or strategic
characteristics that significantly influence whether external
collaboration of domestic SMEs is successful or not. Results suggest
that research and development (R&D) features in general
characteristics (both idea creation and discovering market
opportunities) that focused on and emphasized indirected-market
stakeholders (such as complementary companies and affiliates) and
strategies in innovative strategic characteristics raise the probability of
successful external cooperation. This can be used meaningfully to
build a policy or strategy for inducing successful external cooperation
or to understand the innovation of SMEs.
Abstract: An Artificial Neural Network based modeling
technique has been used to study the influence of different
combinations of meteorological parameters on evaporation from a
reservoir. The data set used is taken from an earlier reported study.
Several input combination were tried so as to find out the importance
of different input parameters in predicting the evaporation. The
prediction accuracy of Artificial Neural Network has also been
compared with the accuracy of linear regression for predicting
evaporation. The comparison demonstrated superior performance of
Artificial Neural Network over linear regression approach. The
findings of the study also revealed the requirement of all input
parameters considered together, instead of individual parameters
taken one at a time as reported in earlier studies, in predicting the
evaporation. The highest correlation coefficient (0.960) along with
lowest root mean square error (0.865) was obtained with the input
combination of air temperature, wind speed, sunshine hours and
mean relative humidity. A graph between the actual and predicted
values of evaporation suggests that most of the values lie within a
scatter of ±15% with all input parameters. The findings of this study
suggest the usefulness of ANN technique in predicting the
evaporation losses from reservoirs.
Abstract: An economic operation scheduling problem of a
hydro-thermal power generation system has been properly solved by
the proposed multipath adaptive tabu search algorithm (MATS). Four
reservoirs with their own hydro plants and another one thermal plant
are integrated to be a studied system used to formulate the objective
function under complicated constraints, eg water managements,
power balance and thermal generator limits. MATS with four subsearch
units (ATSs) and two stages of discarding mechanism (DM),
has been setting and trying to solve the problem through 25 trials
under function evaluation criterion. It is shown that MATS can
provide superior results with respect to single ATS and other
previous methods, genetic algorithms (GA) and differential evolution
(DE).
Abstract: Intelligent deep-drawing is an instrumental research field in sheet metal forming. A set of 28 different experimental data have been employed in this paper, investigating the roles of die radius, punch radius, friction coefficients and drawing ratios for axisymmetric workpieces deep drawing. This paper focuses an evolutionary neural network, specifically, error back propagation in collaboration with genetic algorithm. The neural network encompasses a number of different functional nodes defined through the established principles. The input parameters, i.e., punch radii, die radii, friction coefficients and drawing ratios are set to the network; thereafter, the material outputs at two critical points are accurately calculated. The output of the network is used to establish the best parameters leading to the most uniform thickness in the product via the genetic algorithm. This research achieved satisfactory results based on demonstration of neural networks.
Abstract: Article presents the geometry and structure
reconstruction procedure of the aircraft model for flatter research
(based on the I22-IRYDA aircraft). For reconstruction the Reverse
Engineering techniques and advanced surface modeling CAD tools
are used. Authors discuss all stages of data acquisition process,
computation and analysis of measured data. For acquisition the three
dimensional structured light scanner was used. In the further sections,
details of reconstruction process are present. Geometry
reconstruction procedure transform measured input data (points
cloud) into the three dimensional parametric computer model
(NURBS solid model) which is compatible with CAD systems.
Parallel to the geometry of the aircraft, the internal structure
(structural model) are extracted and modeled. In last chapter the
evaluation of obtained models are discussed.