Abstract: In this paper after reviewing some previous studies, in
order to optimize the above knee prosthesis, beside the inertial
properties a new controlling parameter is informed. This controlling
parameter makes the prosthesis able to act as a multi behavior system
when the amputee is opposing to different environments. This active
prosthesis with the new controlling parameter can simplify the
control of prosthesis and reduce the rate of energy consumption in
comparison to recently presented similar prosthesis “Agonistantagonist
active knee prosthesis".
In this paper three models are generated, a passive, an active, and
an optimized active prosthesis. Second order Taylor series is the
numerical method in solution of the models equations and the
optimization procedure is genetic algorithm.
Modeling the prosthesis which comprises this new controlling
parameter (SEP) during the swing phase represents acceptable results
in comparison to natural behavior of shank. Reported results in this
paper represent 3.3 degrees as the maximum deviation of models
shank angle from the natural pattern. The natural gait pattern belongs
to walking at the speed of 81 m/min.
Abstract: A stack with a small critical temperature gradient is
desirable for a standing wave thermoacoustic engine to obtain a low
onset temperature difference (the minimum temperature difference to
start engine-s self-oscillation). The viscous and heat relaxation loss in
the stack determines the critical temperature gradient. In this work, a
dimensionless critical temperature gradient factor is obtained based
on the linear thermoacoustic theory. It is indicated that the
impedance determines the proportion between the viscous loss, heat
relaxation losses and the power production from the heat energy. It
reveals the effects of the channel dimensions, geometrical
configuration and the local acoustic impedance on the critical
temperature gradient in stacks. The numerical analysis shows that
there exists a possible optimum combination of these parameters
which leads to the lowest critical temperature gradient. Furthermore,
several different geometries have been tested and compared
numerically.
Abstract: This paper describes analysis of low velocity transverse impact on fully backed sandwich beams with composite faces from Eglass/epoxy and cores from Polyurethane or PVC. Indentation on sandwich beams has been analyzed with the existing theories and modeled with the FE code ABAQUS, also loadings have been done experimentally to verify theoretical results. Impact on fully backed has been modeled in two cases of impactor energy with SDOF model (single-degree-of-freedom) and indentation stiffness: lower energy for elastic indentation of sandwich beams and higher energy for plastic area in indentation. Impacts have been modeled by ABAQUS. Impact results can describe response of beam in terms of core and faces thicknesses, core material, indentor energy and energy absorbed. The foam core is modeled using the crushable foam material model and response of the foam core is experimentally characterized in uniaxial compression with higher velocity loading to define quasi impact behaviour.
Abstract: Fuller’s earth is a fine-grained, naturally occurring substance that has a substantial ability to adsorb impurities. In the present study Fuller’s earth has been characterized and used for the removal of Pb(II) from aqueous solution. The effect of various physicochemical parameters such as pH, adsorbent dosage and shaking time on adsorption were studied. The result of the equilibrium studies showed that the solution pH was the key factor affecting the adsorption. The optimum pH for adsorption was 5. Kinetics data for the adsorption of Pb(II) was best described by pseudo-second order model. The effective diffusion co-efficient for Pb(II) adsorption was of the order of 10-8 m2/s. The adsorption data for metal adsorption can be well described by Langmuir adsorption isotherm. The maximum uptake of metal was 103.3 mg/g of adsorbent. Mass transfer analysis was also carried out for the adsorption process. The values of mass transfer coefficients obtained from the study indicate that the velocity of the adsorbate transport from bulk to the solid phase was quite fast. The mean sorption energy calculated from Dubinin-Radushkevich isotherm indicated that the metal adsorption process was chemical in nature.
Abstract: The research is to minimize environmental damage
pertinent to maritime activities about the operation of lighter boat
anchorage and its tugboat. The guidance on upgrading current
harbor service and infrastructure has been provided to Kho Sichang
Municpality. This will involve a study of the maritime logistics of
the water area under jurisdiction of the Sichang island Municipality
and possible recommendations may involve charging taxes,
regulations and fees. With implementing these recommendations will
help in protection of the marine environment and in increasing
operator functionality. Additionally, our recommendation is to
generate a consistent revenue stream to the municipality. The action
items contained in this research are feasible and effective, the success
of these initiatives are heavily dependent upon successful promotion
and enforcement. Promoting new rules and regulations effectively
and peacefully can be done through theories and techniques used in
the psychology of persuasion. In order to assure compliance with the
regulations, the municipality must maintain stringent patrols and
fines for violators. In order to become success, the Municipality
must preserve a consistent, transparent and significant enforcement
system. Considering potential opportunities outside of the current
state of the municipality, the authors recommend that Koh Sichang be
given additional jurisdiction to capture value from the master vessels,
as well as to confront the more significant environmental challenges
these vessels pose. Finally, the authors recommend that the Port of
Koh Sichang Island obtain a free port status in order to increase
economic viability and overall sustainability.
Abstract: The comparisons of two typical fluidic thrust vectoring exhaust nozzles including two-dimensional(2-D) nozzle and axisymmetric nozzle on aerodynamic characteristics was presented by numerical simulation. The results show: the thrust vector angles increased with the increasing secondary flow but decreased with the nozzle pressure ratio (NPR) increasing. With the same secondary flow and NPR, the thrust vector angles of 2-D nozzle were higher than the axisymmetric nozzle-s. So with the lower NPR and more secondary weight flow, the much higher thrust vector angle was caused by 2-D fluidic nozzle. And with the higher NPR and less secondary weight flow, there was not much difference in angular dimension between two nozzles.
Abstract: Zero inflated Strict Arcsine model is a newly developed model which is found to be appropriate in modeling overdispersed count data. In this study, maximum likelihood estimation method is used in estimating the parameters for zero inflated strict arcsine model. Bootstrapping is then employed to compute the confidence intervals for the estimated parameters.
Abstract: In this paper, a Dynamic Economic Dispatch (DED) model is developed for the system consisting of both thermal generators and wind turbines. The inclusion of a significant amount of wind energy into power systems has resulted in additional constraints on DED to accommodate the intermittent nature of the output. The probability of stochastic wind power based on the Weibull probability density function is included in the model as a constraint; A Here-and-Now Approach. The Environmental Protection Agency-s hourly emission target, which gives the maximum emission during the day, is used as a constraint to reduce the atmospheric pollution. A 69-bus test system with non-smooth cost function is used to illustrate the effectiveness of the proposed model compared with static economic dispatch model with including the wind power.
Abstract: A fundamental model consisting of charged particles
moving in free space exposed to alternating and direct current (ACDC)
electromagnetic fields is analyzed. Effects of charged particles
initial position and initial velocity to cyclotron resonance frequency
are observed. Strong effects are observed revealing that effects of
electric and magnetic fields on a charged particle in free space
varies with the initial conditions. This indicates the frequency where
maximum displacement occur can be changed. At this frequency
the amplitude of oscillation of the particle displacement becomes
unbounded.
Abstract: The mechanical deformation and the electrical conductivity of lanthanum strontium cobalt ferrite oxide under uniaxial compression were investigated at various temperatures up to 1073 K. The material reveals a rather complex mechanical behaviour related to its ferroelasticity and completely different stress-strain curves are obtained during the 1st and 2nd loading cycles. A distinctive ferroelastic creep was observed at 293 K whilst typical ferroelastic stress-strain curve were obtained in the temperature range from 473 K to 873 K. At 1073 K, on the other hand, high-temperature creep deformation was observed instead of ferroelastic deformation. The conductivity increases with increasing compressive stress at all the temperatures. The increase in conductivity is related to both geometrical and piezoelectric effects. From 293 K to 873 K, where the material exhibits ferroelastic behaviour, the variation in the total conductivity decreases with increasing temperature. The contribution of the piezoelectric effect to the total conductivity variation also decreases with increasing temperature and the maximum in piezoconductivity has a value of about 0.75 % at 293 K for a compressive stress of 100 MPa. There is no effect of domain switching on conductivity except for the geometric effect. At 1073 K, the conductivity is simply proportional to the compressive strain.
Abstract: Image clustering is a process of grouping images
based on their similarity. The image clustering usually uses the color
component, texture, edge, shape, or mixture of two components, etc.
This research aims to explore image clustering using color
composition. In order to complete this image clustering, three main
components should be considered, which are color space, image
representation (feature extraction), and clustering method itself. We
aim to explore which composition of these factors will produce the
best clustering results by combining various techniques from the
three components. The color spaces use RGB, HSV, and L*a*b*
method. The image representations use Histogram and Gaussian
Mixture Model (GMM), whereas the clustering methods use KMeans
and Agglomerative Hierarchical Clustering algorithm. The
results of the experiment show that GMM representation is better
combined with RGB and L*a*b* color space, whereas Histogram is
better combined with HSV. The experiments also show that K-Means
is better than Agglomerative Hierarchical for images clustering.
Abstract: Gliding during night without electric power is an efficient method to enhance endurance performance of solar aircrafts. The properties of maximum gliding endurance path are studied in this paper. The problem is formulated as an optimization problem about maximum endurance can be sustained by certain potential energy storage with dynamic equations and aerodynamic parameter constrains. The optimal gliding path is generated based on gauss pseudo-spectral method. In order to analyse relationship between altitude, velocity of solar UAVs and its endurance performance, the lift coefficient in interval of [0.4, 1.2] and flight envelopes between 0~30km are investigated. Results show that broad range of lift coefficient can improve solar aircrafts- long endurance performance, and it is possible for a solar aircraft to achieve the aim of long endurance during whole night just by potential energy storage.
Abstract: Real world Speaker Identification (SI) application
differs from ideal or laboratory conditions causing perturbations that
leads to a mismatch between the training and testing environment
and degrade the performance drastically. Many strategies have been
adopted to cope with acoustical degradation; wavelet based Bayesian
marginal model is one of them. But Bayesian marginal models
cannot model the inter-scale statistical dependencies of different
wavelet scales. Simple nonlinear estimators for wavelet based
denoising assume that the wavelet coefficients in different scales are
independent in nature. However wavelet coefficients have significant
inter-scale dependency. This paper enhances this inter-scale
dependency property by a Circularly Symmetric Probability Density
Function (CS-PDF) related to the family of Spherically Invariant
Random Processes (SIRPs) in Log Gabor Wavelet (LGW) domain
and corresponding joint shrinkage estimator is derived by Maximum
a Posteriori (MAP) estimator. A framework is proposed based on
these to denoise speech signal for automatic speaker identification
problems. The robustness of the proposed framework is tested for
Text Independent Speaker Identification application on 100 speakers
of POLYCOST and 100 speakers of YOHO speech database in three
different noise environments. Experimental results show that the
proposed estimator yields a higher improvement in identification
accuracy compared to other estimators on popular Gaussian Mixture
Model (GMM) based speaker model and Mel-Frequency Cepstral
Coefficient (MFCC) features.
Abstract: This study was carried out to develop a flotation
procedure for an oxide copper ore from a Region in Central Africa
for producing an 18% copper concentrate for downstream processing
at maximum recovery from a 4% copper feed grade. The copper
recoveries achieved from the test work were less than 50% despite
changes in reagent conditions (multistage sulphidisation, use of RCA
emulsion and mixture, use of AM 2, etc). The poor recoveries were
attributed to the mineralogy of the ore from which copper silicates
accounted for approximately 70% (mass) of the copper minerals in
the ore. These can be complex and difficult to float using
conventional flotation methods. Best results were obtained using
basic sulphidisation procedures, a high flotation temperature and
extended flotation residence time.
Abstract: Group key management is an important functional
building block for any secure multicast architecture.
Thereby, it has been extensively studied in the literature.
In this paper we present relevant group key management
protocols. Then, we compare them against some pertinent
performance criteria.
Abstract: The Spalart and Allmaras turbulence model has been
implemented in a numerical code to study the compressible turbulent
flows, which the system of governing equations is solved with a
finite volume approach using a structured grid. The AUSM+ scheme
is used to calculate the inviscid fluxes. Different benchmark
problems have been computed to validate the implementation and
numerical results are shown. A special Attention is paid to wall jet
applications. In this study, the jet is submitted to various wall
boundary conditions (adiabatic or uniform heat flux) in forced
convection regime and both two-dimensional and axisymmetric wall
jets are considered. The comparison between the numerical results
and experimental data has given the validity of this turbulence model
to study the turbulent wall jets especially in engineering applications.
Abstract: The balancing numbers are natural numbers n satisfying
the Diophantine equation 1 + 2 + 3 + · · · + (n - 1) = (n + 1) +
(n + 2) + · · · + (n + r); r is the balancer corresponding to the
balancing number n.The nth balancing number is denoted by Bn
and the sequence {Bn}1
n=1 satisfies the recurrence relation Bn+1 =
6Bn-Bn-1. The balancing numbers posses some curious properties,
some like Fibonacci numbers and some others are more interesting.
This paper is a study of recurrent sequence {xn}1
n=1 satisfying the
recurrence relation xn+1 = Axn - Bxn-1 and possessing some
curious properties like the balancing numbers.
Abstract: Today, Hydroforming technology provides an
attractive alternative to conventional matched die forming, especially
for cost-sensitive, lower volume production, and for parts with
irregular contours. In this study the critical fluid pressures which lead
to rupture in the workpiece has been investigated by theoretical and
finite element methods. The axisymmetric analysis was developed to
investigate the tearing phenomenon in cylindrical Hydroforming
Deep Drawing (HDD). By use of obtained equations the effect of
anisotropy, drawing ratio, sheet thickness and strain hardening
exponent on tearing diagram were investigated.
Abstract: As the fossil fuels kept on depleting, intense research in developing hydrogen (H2) as the alternative fuel has been done to cater our tremendous demand for fuel. The potential of H2 as the ultimate clean fuel differs with the fossil fuel that releases significant amounts of carbon dioxide (CO2) into the surrounding and leads to the global warming. The experimental work was carried out to study the production of H2 from palm kernel shell steam gasification at different variables such as heating rate, steam to biomass ratio and adsorbent to biomass ratio. Maximum H2 composition which is 61% (volume basis) was obtained at heating rate of 100oCmin-1, steam/biomass of 2:1 ratio, and adsorbent/biomass of 1:1 ratio. The commercial adsorbent had been modified by utilizing the alcoholwater mixture. Characteristics of both adsorbents were investigated and it is concluded that flowability and floodability of modified CaO is significantly improved.
Abstract: In this paper, propagation of cos-Gaussian beam in strongly nonlocal nonlinear media has been stimulated by using paraxial group transformation. At first, cos-Gaussian beam, nonlocal nonlinear media, critical power, transfer matrix, and paraxial group transformation are introduced. Then, the propagation of the cos-Gaussian beam in strongly nonlocal nonlinear media is simulated. Results show that beam propagation has periodic structure during self-focusing effect in this case. However, this simple method can be used for investigation of propagation of kinds of beams in ABCD optical media.