Abstract: 98% of the energy needed in Taiwan has been
imported. The prices of petroleum and electricity have been
increasing. In addition, facility capacity, amount of electricity
generation, amount of electricity consumption and number of Taiwan
Power Company customers have continued to increase. For these
reasons energy conservation has become an important topic. In the
past linear regression was used to establish the power consumption
models for chillers. In this study, grey prediction is used to evaluate
the power consumption of a chiller so as to lower the total power
consumption at peak-load (so that the relevant power providers do not
need to keep on increasing their power generation capacity and facility
capacity).
In grey prediction, only several numerical values (at least four
numerical values) are needed to establish the power consumption
models for chillers. If PLR, the temperatures of supply chilled-water
and return chilled-water, and the temperatures of supply cooling-water
and return cooling-water are taken into consideration, quite accurate
results (with the accuracy close to 99% for short-term predictions)
may be obtained. Through such methods, we can predict whether the
power consumption at peak-load will exceed the contract power
capacity signed by the corresponding entity and Taiwan Power
Company. If the power consumption at peak-load exceeds the power
demand, the temperature of the supply chilled-water may be adjusted
so as to reduce the PLR and hence lower the power consumption.
Abstract: Three dimensional simulations are carried out to estimate the effect of wind direction, wind speed and geometry on the flow and dispersion of vehicular pollutant in a street canyon. The pollutant sources are motor vehicles passing between the two buildings. Suitable emission factors for petrol and diesel vehicles at varying vehicle speed are used for the estimation of the rate of emission from the streets. The dispersion of automobile pollutant released from the street is simulated by introducing vehicular emission source term as a fixed-flux boundary condition at the ground level over the road. The emission source term is suitably calculated by adopting emission factors from literature for varying conditions of street traffic. It is observed that increase in wind angle disturbs the symmetric pattern of pollution distribution along the street length. The concentration increases in the far end of the street as compared to the near end.
Abstract: The presence of toxic heavy metals in industrial
effluents is one of the serious threats to the environment. Heavy
metals such as Cadmium, Chromium, Lead, Nickel, Zinc, Mercury,
Copper, Arsenic are found in the effluents of industries such as
foundries, electroplating, petrochemical, battery manufacturing,
tanneries, fertilizer, dying, textiles, metallurgical and metal finishing.
Tremendous increase of industrial copper usage and its presence in
industrial effluents has lead to a growing concern about the fate and
effects of Copper in the environment. Percolation of industrial
effluents through soils leads to contamination of ground water and
soils. The transport of heavy metals and their diffusion into the soils
has therefore, drawn the attention of the researchers.
In this study, an attempt has been made to delineate the
mechanisms of transport and fate of copper in terrestrial
environment. Column studies were conducted using perplex glass
square column of dimension side 15 cm and 1.35 m long. The soil
samples were collected from a natural drain near Mohali (India). The
soil was characterized to be poorly graded sandy loam. The soil was
compacted to the field dry density level of about 1.6 g/cm3. Break
through curves for different depths of the column were plotted. The
results of the column study indicated that the copper has high
tendency to flow in the soils and fewer tendencies to get absorbed on
the soil particles. The t1/2 estimates obtained from the studies can be
used for design copper laden wastewater disposal systems.
Abstract: There is growing interest in biodiesel (fatty acid
methyl ester or FAME) because of the similarity in its properties
when compared to those of diesel fuels. Diesel engines operated on
biodiesel have lower emissions of carbon monoxide, unburned
hydrocarbons, particulate matter, and air toxics than when operated
on petroleum-based diesel fuel. Production of fatty acid methyl ester
(FAME) from rapeseed (nonedible oil) fatty acid distillate having
high free fatty acids (FFA) was investigated in this work. Conditions
for esterification process of rapeseed oil were 1.8 % H2SO4 as
catalyst, MeOH/oil of molar ratio 2 : 0.1 and reaction temperature
65 °C, for a period of 3h. The yield of methyl ester was > 90 % in 1
h.
The amount of FFA was reduced from 93 wt % to less than 2 wt %
at the end of the esterification process. The FAME was pureed by
neutralization with 1 M sodium hydroxide in water solution at a
reaction temperature of 62 °C. The final FAME product met with the
biodiesel quality standard, and ASTM D 6751.
Abstract: In this paper usefulness of quasi-Newton iteration
procedure in parameters estimation of the conditional variance
equation within BHHH algorithm is presented. Analytical solution of
maximization of the likelihood function using first and second
derivatives is too complex when the variance is time-varying. The
advantage of BHHH algorithm in comparison to the other
optimization algorithms is that requires no third derivatives with
assured convergence. To simplify optimization procedure BHHH
algorithm uses the approximation of the matrix of second derivatives
according to information identity. However, parameters estimation in
a/symmetric GARCH(1,1) model assuming normal distribution of
returns is not that simple, i.e. it is difficult to solve it analytically.
Maximum of the likelihood function can be founded by iteration
procedure until no further increase can be found. Because the
solutions of the numerical optimization are very sensitive to the
initial values, GARCH(1,1) model starting parameters are defined.
The number of iterations can be reduced using starting values close
to the global maximum. Optimization procedure will be illustrated in
framework of modeling volatility on daily basis of the most liquid
stocks on Croatian capital market: Podravka stocks (food industry),
Petrokemija stocks (fertilizer industry) and Ericsson Nikola Tesla
stocks (information-s-communications industry).
Abstract: The development and application of wind power for
renewable energy has attracted growing interest in recent years. Renewable energy sources are attracting much alteration as they can
reduce both environmental damage and dependence on fossil fuels. With the growing need for sustainable energy supplies, a case is made
for decentralized, stand-alone power supplies (SAPS) as an alternative to power grids. In the era which traditional petroleum energy resource
decreasing and the green house affect significant increasing, the development and usage of regenerative resources is inevitable. Due to the contribution of the pioneers, the development of regenerative resources already has a remarkable achievement; however, in the view of economy and quantity, it is still a long road for regenerative energy
to replace traditional petroleum energy. In our prospective, in stead of
investigate larger regenerative energy equipment, it is much wiser to
think about the blind side and breakthrough of the current technique.
Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.
Abstract: Canola is a specific edible type of rapeseed, developed
in the 1970s, which contains about 40 percent oil. This research was
carried out to determine the yield and some quality characteristics of
some winter canola cultivars during the 2010-2011 vegetation period
in Central Anatolia of Turkey. In this research; Oase, Dante,
Californium, Excalibur, Elvis, ES Hydromel, Licord, Orkan, Vectra,
Nelson, Champlain and NK Petrol winter canola varieties were used
as material. The field experiment was set up in a “Randomized
Complete Block Design” with three replications on 21 September
2010. In this research; seed yield, oil content, protein content, oil
yield and protein yield were examined.
As a result of this research; seed yield, oil content, oil yield and
protein yield (except protein content) were significant differences
between the cultivars. The highest seed yield (6348 kg ha-1) was
obtained from the NK Petrol, while the lowest seed yield (3949 kg
ha-1) was determined from the Champlain cultivar was obtained. The
highest oil content (46.73%) was observed from Oase and the lowest
value was obtained from Vectra (41.87%) cultivar. The highest oil
yield (2950 kg ha-1) was determined from NK Petrol while the least
value (1681 kg ha-1) was determined from Champlain cultivar. The
highest protein yield (1539.3 kg ha-1) was obtained from NK Petrol
and the lowest protein yield (976.5 kg ha-1) was obtained from
Champlain cultivar.
The main purpose of the cultivation of oil crops, to increase the
yield of oil per unit area. According the result of this research, NK
Petrol cultivar which ranks first with regard to both seed yield and oil
yield between cultivars as the most suitable winter canola cultivar of
local conditions.
Abstract: Anaerobic treatment has many advantages over other
biological method particularly when used to treat complex
wastewater such as petroleum refinery wastewater. In this study two
Up-flow Anaerobic Sludge Blanket (UASB) reactors were operated
in parallel to treat six volumetric organic loads (0.58, 1.21, 0.89,
2.34, 1.47 and 4.14 kg COD/m3·d) to evaluate the chemical oxygen
demand (COD) removal efficiency. The reactors were continuously
adapting to the changing of operation condition with increase in the
removal efficiency or slight decrease until the last load which was
more than two times the load, at which the reactor stressed and the
removal efficiency decreased to 75% with effluent concentration of
1746 mg COD/L. Other parameters were also monitored such as pH,
alkalinity, volatile fatty acid and gas production rate. The UASB
reactor was suitable to treat petroleum refinery wastewater and the
highest COD removal rate was 83% at 1215 kg/m3·d with COD
concentration about 356 mg/L in the effluent.
Abstract: There have been widespread applications of fluidized beds in industries which are related to the combination of gas-solid particles during the last decade. For instance, in order to crack the catalyses in petrochemical industries or as a drier in food industries. High capacity of fluidized bed in heat and mass transfer has made this device very popular. In order to achieve a higher efficiency of fluidized beds, a particular attention has been paid to beds with pulsating air flow. In this paper, a fluidized bed device with pulsating flow has been designed and constructed. Size of particles have been used during the test are in the range of 40 to 100μm. The purpose of this experimental test is to investigate the air flow regime, observe the particles- movement and measure the pressure loss along the bed. The effects of pulsation can be evaluated by comparing the results for both continuous and pulsating flow. Results of both situations are compared for various gas speeds. Moreover the above experiment is numerically simulated by using Fluent software and its numerical results are compared with the experimental results.
Abstract: Cenozoic basalts found in Jiangsu province of eastern
China include tholeiites and alkali basalts. The present paper analyzed
the major, trace elements, rare earth elements of these Cenozoic
basalts and combined with Sr-Nd isotopic compositions proposed by
Chen et al. (1990)[1] in the literatures to discuss the petrogenesis of
these basalts and the geochemical characteristics of the source mantle.
Based on major, trace elements and fractional crystallization model
established by Brooks and Nielsen (1982)[2] we suggest that the
basaltic magma has experienced olivine + clinopyroxene fractionation
during its evolution. The chemical compositions of basaltic rocks from
Jiangsu province indicate that these basalts may belong to the same
magmatic system. Spidergrams reveal that Cenozoic basalts from
Jiangsu province have geochemical characteristics similar to those of
ocean island basalts(OIB). The slight positive Nb and Ti anomalies
found in basaltic rocks of this study suggest the presence of Ti-bearing
minerals in the mantle source and these Ti-bearing minerals had
contributed to basaltic magma during partial melting, indicating a
metasomatic event might have occurred before the partial melting.
Based on the Sr vs. Nd isotopic ratio plots, we suggest that Jiangsu
basalts may be derived from partial melting of mantle source which
may represent two-end members mixing of DMM and EM-I. Some
Jiangsu basaltic magma may be derived from partial melting of EM-I
heated by the upwelling asthenospheric mantle or asthenospheric
diapirism.
Abstract: The concurrent era is characterised by strengthened interactions among financial markets and increased capital mobility globally. In this frames we examine the effects the international financial integration process has on the European bond markets. We perform a comparative study of the interactions of the European and international bond markets and exploit Cointegration analysis results on the elimination of stochastic trends and the decomposition of the underlying long run equilibria and short run causal relations. Our investigation provides evidence on the relation between the European integration process and that of globalisation, viewed through the bond markets- sector. Additionally the structural formulation applied, offers significant implications of the findings. All in all our analysis offers a number of answers on crucial queries towards the European bond markets integration process.
Abstract: It has been shown that the solution of water shortage problem in Central Asia closely connected with inclusion of atmosphere water vapour into the system of response and water resources management. Some methods of water extraction from atmosphere have been discussed.
Abstract: Structural Integrity Management (SIM) is
important for the protection of offshore crew, environment, business assets and company and industry reputation. API RP 2A contained guidelines for assessment of existing platforms mostly for the Gulf
of Mexico (GOM). ISO 19902 SIM framework also does not
specifically cater for Malaysia. There are about 200 platforms in
Malaysia with 90 exceeding their design life. The Petronas Carigali
Sdn Bhd (PCSB) uses the Asset Integrity Management System and
the very subjective Risk based Inspection Program for these
platforms. Petronas currently doesn-t have a standalone Petronas
Technical Standard PTS-SIM. This study proposes a recommended
practice for the SIM process for offshore structures in Malaysia,
including studies by API and ISO and local elements such as the
number of platforms, types of facilities, age and risk ranking. Case
study on SMG-A platform in Sabah shows missing or scattered
platform data and a gap in inspection history. It is to undergo a level
3 underwater inspection in year 2015.
Abstract: Petrol Fuel Station (PFS) has potential hazards to the
people, asset, environment and reputation of an operating company.
Fire hazards, static electricity air pollution evoked by aliphatic and
aromatic organic compounds are major causes of accident/incident
occurrence at fuel station. Activities such as carelessness,
maintenance, housekeeping, slips trips and falls, transportation
hazard, major and minor injuries, robbery and snake bites has a
potential to create unsafe conditions. The level of risk of these
hazards varies according to location and country. The emphasis on
safety considerations by the government is variable all around the
world. Developed countries safety records are much better as
compared to developing countries safety statistics. There is no
significant approach available to highlight the unsafe acts and unsafe
conditions during operation and maintenance of fuel station. Fuel
station is the most commonly available facilities that contain
flammable and hazardous materials. Due to continuous operation of
fuel station they pose various hazards to people, environment and
assets of an organization. To control these hazards, there is a need for
specific approach. PFS operation is unique as compared to other
businesses. For smooth operations it demands an involvement of
operating company, contractor and operator group. This study will
focus to address hazard contributing factors that have a potential to
make PFS operation risky. One year data collected, 902 activities
analyzed, comparisons were made to highlight significant
contributing factors. The study will provide help and assistance to
PFS outlet marketing companies to make their fuel station operation
safer. It will help health safety and environment (HSE) professionals
to arrest the gap available related to safety matters at PFS.
Abstract: Programmable logic controllers are the main controllers in the today's industries; they are used for several applications in industrial control systems and there are lots of examples exist from the PLC applications in industries especially in big companies and plants such as refineries, power plants, petrochemical companies, steel companies, and food and production companies. In the PLCs there are some functions in the function library in software that can be used in PLC programs as basic program elements. The aim of this project are introducing and implementing a new function block of a neural network to the function library of PLC. This block can be applied for some control applications or nonlinear functions calculations after it has been trained for these applications. The implemented neural network is a Perceptron neural network with three layers, three input nodes and one output node. The block can be used in manual or automatic mode. In this paper the structure of the implemented function block, the parameters and the training method of the network are presented by considering the especial method of PLC programming and its complexities. Finally the application of the new block is compared with a classic simulated block and the results are presented.
Abstract: The recovery of metal values and safe disposal of
spent catalyst is gaining interest due to both its hazardous nature and
increased regulation associated with disposal methods. Prior to the
recovery of the valuable metals, removal of entrained deposits limit
the diffusion of lixiviate resulting in low recovery of metals must be
taken into consideration. Therefore, petroleum refinery spent catalyst
was subjected to acetone washing and roasting at 500oC. The treated
samples were investigated for metals bioleaching using
Acidithiobacillus ferrooxidans in batch reactors and the leaching
efficiencies were compared. It was found out that acetone washed
spent catalysts results in better metal recovery compare to roasted
spent. About 83% Ni, 20% Al, 50% Mo and 73% V were leached
using the acetone washed spent catalyst. In both the cases, Ni, V and
Mo was high compared to Al.
Abstract: Explosion occurs due to sudden release of energy.
Common examples of explosion include chemical, atomic, heat, and
pressure tank (due to ignition) explosions. Petroleum, gas, and
petrochemical industries operations are threatened by natural risks
and processes. Fires and explosions are the greatest process risks
which cause financial damages.
This study aims at designing a single-floor structure for the control
room of a petroleum refinery to be resistant against gas explosion
loads, and the information related to the structure specifications have
been provided regarding the fact that the structure is made on the
ground's surface. In this research, the lateral stiffness of single pile is
calculated by SPPLN.FOR computer program, and its value for
13624 KN/m single pile has been assessed. The analysis used due to
the loading conditions, is dynamic nonlinear analysis with direct
integration method.
Abstract: Theobjective of this study was to evaluate the optimal
treatment condition of Fenton oxidation process to removal
contaminant in soil slurry contaminated by petroleum hydrocarbons.
This research studied somefactors that affect the removal efficiency
of petroleum hydrocarbons in soil slurry including molar ratio of
hydrogen peroxide (H2O2) to ferrous ion(Fe2+), pH condition and
reaction time.The resultsdemonstrated that the optimum condition
was that the molar ratio of H2O2:Fe3+ was 200:1,the pHwas 4.0and
the rate of reaction was increasing rapidly from starting point to 7th
hour and destruction kinetic rate (k) was 0.24 h-1. Approximately
96% of petroleum hydrocarbon was observed(initialtotal petroleum
hydrocarbon (TPH) concentration = 70±7gkg-1)
Abstract: There was a high rate of corrosion in Pyrolysis
Gasoline Hydrogenation (PGH) unit of Arak Petrochemical Company
(ARPC), and it caused some operational problem in this plant. A
commercial chemical had been used as anti-corrosion in the
depentanizer column overhead in order to control the corrosion rate.
Injection of commercial corrosion inhibitor caused some
operational problems such as fouling in some heat exchangers. It was
proposed to replace this commercial material with another more
effective trouble free, and well-known additive by R&D and
operation specialists.
At first, the system was simulated by commercial simulation
software in electrolytic system to specify low pH points inside the
plant. After a very comprehensive study of the situation and technical
investigations ,ammonia / monoethanol amine solution was proposed
as neutralizer or corrosion inhibitor to be injected in a suitable point
of the plant. For this purpose, the depentanizer column and its
accessories system was simulated again in case of this solution
injection.
According to the simulation results, injection of new anticorrosion
substance has no any side effect on C5 cut product and
operating conditions of the column. The corrosion rate will be
cotrolled, if the pH remains at the range of 6.5 to 8 . Aactual plant
test run was also carried out by injection of ammonia / monoethanol
amine solution at the rate of 0.6 Kg/hr and the results of iron content
of water samples and corrosion test coupons confirmed the
simulation results.
Now, ammonia / monoethanol amine solution is injected to a
suitable pint inside the plant and corrosion rate has decreased
significantly.