Abstract: Wetting efficiency of microstructures or nanostructures patterned on Si wafers is a real challenge in integrated circuits manufacturing. In fact, bad or non-uniform wetting during wet processes limits chemical reactions and can lead to non-complete etching or cleaning inside the patterns and device defectivity. This issue is more and more important with the transistors size shrinkage and concerns mainly high aspect ratio structures. Deep Trench Isolation (DTI) structures enabling pixels’ isolation in imaging devices are subject to this phenomenon. While low-frequency acoustic reflectometry principle is a well-known method for Non Destructive Test applications, we have recently shown that it is also well suited for nanostructures wetting characterization in a higher frequency range. In this paper, we present a high-frequency acoustic reflectometry characterization of DTI wetting through a confrontation of both experimental and modeling results. The acoustic method proposed is based on the evaluation of the reflection of a longitudinal acoustic wave generated by a 100 µm diameter ZnO piezoelectric transducer sputtered on the silicon wafer backside using MEMS technologies. The transducers have been fabricated to work at 5 GHz corresponding to a wavelength of 1.7 µm in silicon. The DTI studied structures, manufactured on the wafer frontside, are crossing trenches of 200 nm wide and 4 µm deep (aspect ratio of 20) etched into a Si wafer frontside. In that case, the acoustic signal reflection occurs at the bottom and at the top of the DTI enabling its characterization by monitoring the electrical reflection coefficient of the transducer. A Finite Difference Time Domain (FDTD) model has been developed to predict the behavior of the emitted wave. The model shows that the separation of the reflected echoes (top and bottom of the DTI) from different acoustic modes is possible at 5 Ghz. A good correspondence between experimental and theoretical signals is observed. The model enables the identification of the different acoustic modes. The evaluation of DTI wetting is then performed by focusing on the first reflected echo obtained through the reflection at Si bottom interface, where wetting efficiency is crucial. The reflection coefficient is measured with different water / ethanol mixtures (tunable surface tension) deposited on the wafer frontside. Two cases are studied: with and without PFTS hydrophobic treatment. In the untreated surface case, acoustic reflection coefficient values with water show that liquid imbibition is partial. In the treated surface case, the acoustic reflection is total with water (no liquid in DTI). The impalement of the liquid occurs for a specific surface tension but it is still partial for pure ethanol. DTI bottom shape and local pattern collapse of the trenches can explain these incomplete wetting phenomena. This high-frequency acoustic method sensitivity coupled with a FDTD propagative model thus enables the local determination of the wetting state of a liquid on real structures. Partial wetting states for non-hydrophobic surfaces or low surface tension liquids are then detectable with this method.
Abstract: This paper presents a digital non-linear pulse-width modulation (PWM) controller in a high-voltage (HV) buck-boost DC-DC converter for the piezoelectric transducer of the down-hole acoustic telemetry system. The proposed design controls the generation of output signal with voltage higher than the supply voltage and is targeted to work under high temperature. To minimize the power consumption and silicon area, a simple and efficient design scheme is employed to develop the PWM controller. The proposed PWM controller consists of serial to parallel (S2P) converter, data assign block, a mode and duty cycle controller (MDC), linearly PWM (LPWM) and noise shaper, pulse generator and clock generator. To improve the reliability of circuit operation at higher temperature, this design is fabricated with the 1.0-μm silicon-on-insulator (SOI) CMOS process. The implementation results validated that the proposed design has the advantages of smaller size, lower power consumption and robust thermal stability.
Abstract: The paper presents the results of the molecular
genetics analysis in sports research, with special emphasis to use
genetic information in diagnosing of motoric predispositions in Roma
boys from East Slovakia. The ability and move are the basic
characteristics of all living organisms. The phenotypes are influenced
by a combination of genetic and environmental factors. Genetic tests
differ in principle from the traditional motoric tests, because
the DNA of an individual does not change during life. The aim of
the presented study was to examine motion abilities and to determine
the frequency of ACTN3 (R577X) gene in Roma children. Genotype
data were obtained from 138 Roma and 155 Slovak boys from 7 to 15
years old. Children were investigated on physical performance level
in association with their genotype. Biological material for genetic
analyses comprised samples of buccal swabs. Genotypes were
determined using Real Time High resolution melting PCR method
(Rotor-Gene 6000 Corbett and Light Cycler 480 Roche). The
software allows creating reports of any analysis, where information
of the specific analysis, normalized and differential graphs and many
information of the samples are shown. Roma children of analyzed
group legged to non-Romany children at the same age in all the
compared tests. The % distribution of R and X alleles in Roma
children was different from controls. The frequency of XX genotype
was 9.26%, RX 46.33% and RR was 44.41%. The frequency of XX
genotype was 9.26% which is comparable to a frequency of an Indian
population. Data were analyzed with the ANOVA test.
Abstract: We have incorporated the translational rotational (TR)
coupling effects in the framework of three body force shell model
(TSM) to develop an extended TSM (ETSM). The dynamical matrix
of ETSM has been applied to compute the phonon frequencies of
orientationally disordered mixed crystal (ND4Br)x(KBr)1-x in (q00),
(qq0) and (qqq) symmetry directions for compositions 0.10≤x≤0.50
at T=300K.These frequencies are plotted as a function of wave vector
k. An unusual acoustic mode softening is found along symmetry
directions (q00) and (qq0) as a result of translation-rotation coupling.
Abstract: The recent tendency of ”Internet of Things” (IoT) has
developed in the last years, causing the emergence of innovative
communication methods among multiple devices. The appearance of
Bluetooth Low Energy (BLE) has allowed a push to IoT in relation
to smartphones. In this moment, a set of new applications related to
several topics like entertainment and advertisement has begun to be
developed but not much has been done till now to take advantage
of the potential that these technologies can offer on many business
areas and in everyday tasks. In the present work, the application of
BLE technology and smartphones is proposed on some business areas
related to the optimization of resource allocation in huge facilities
like airports. An indoor location system has been developed through
triangulation methods with the use of BLE beacons. The described
system can be used to locate all employees inside the building
in such a way that any task can be automatically assigned to a
group of employees. It should be noted that this system cannot
only be used to link needs with employees according to distances,
but it also takes into account other factors like occupation level or
category. In addition, it has been endowed with a security system
to manage business and personnel sensitive data. The efficiency of
communications is another essential characteristic that has been taken
into account in this work.
Abstract: The acoustomagnetoelectric (AME) field in a rectangular quantum wire with an infinite potential (RQWIP) is calculated in the presence of an external magnetic field (EMF) by using the quantum kinetic equation for the distribution function of electrons system interacting with external phonons and electrons scattering with internal acoustic phonon in a RQWIP. We obtained ananalytic expression for the AME field in the RQWIP in the presence of the EMF. The dependence of AME field on the frequency of external acoustic wave, the temperature T of system, the cyclotron frequency of the EMF and the intensity of the EMF is obtained. Theoretical results for the AME field are numerically evaluated, plotted and discussed for a specific RQWIP GaAs/GaAsAl. This result has shown that the dependence of the AME field on intensity of the EMF is nonlinearly and it is many distinct maxima in the quantized magnetic region. We also compared received fields with those for normal bulk semiconductors, quantum well and quantum wire to show the difference. The influence of an EMF on AME field in a RQWIP is newly developed.
Abstract: Water is a very rare natural resource in South Africa. Ga-Selati River is used for both domestic and industrial purposes. This study was carried out in order to assess the quality of Ga-Selati River in a mining area of Limpopo Province-Phalaborwa. The pH, Electrical Conductivity (EC) and Total Dissolved Solids (TDS) were determined using a Crinson multimeter while turbidity was measured using a Labcon Turbidimeter. The concentrations of Al, Ca, Cd, Cr, Fe, K, Mg, Mn, Na and Pb were analysed in triplicate using a Varian 520 flame atomic absorption spectrometer (AAS) supplied by PerkinElmer, after acid digestion with nitric acid in a fume cupboard. The average pH of the river from eight different sampling sites was 8.00 and 9.38 in wet and dry season respectively. Higher EC values were determined in the dry season (138.7 mS/m) than in the wet season (96.93 mS/m). Similarly, TDS values were higher in dry (929.29 mg/L) than in the wet season (640.72 mg/L) season. These values exceeded the recommended guideline of South Africa Department of Water Affairs and Forestry (DWAF) for domestic water use (70 mS/m) and that of the World Health Organization (WHO) (600 mS/m), respectively. Turbidity varied between 1.78-5.20 and 0.95-2.37 NTU in both wet and dry seasons. Total hardness of 312.50 mg/L and 297.75 mg/L as the concentration of CaCO3 was computed for the river in both the wet and the dry seasons and the river water was categorised as very hard. Mean concentration of the metals studied in both the wet and the dry seasons are: Na (94.06 mg/L and 196.3 mg/L), K (11.79 mg/L and 13.62 mg/L), Ca (45.60 mg/L and 41.30 mg/L), Mg (48.41 mg/L and 44.71 mg/L), Al (0.31 mg/L and 0.38 mg/L), Cd (0.01 mg/L and 0.01 mg/L), Cr (0.02 mg/L and 0.09 mg/L), Pb (0.05 mg/L and 0.06 mg/L), Mn (0.31 mg/L and 0.11 mg/L) and Fe (0.76 mg/L and 0.69 mg/L). Results from this study reveal that most of the metals were present in concentrations higher than the recommended guidelines of DWAF and WHO for domestic use and the protection of aquatic life.
Abstract: Measurement of the ultrasonic pulse velocity (UPV) is an important tool in diagnostic examination of concrete. In this method piezoelectric transducers are normally held in direct contact with the concrete surface. The current study aims to test the hypothesis that a preferential coupling effect might exist i.e. that the speed of sound measured depends on the couplant used. In this study, different coupling media of varying acoustic impedance were placed between the transducers and concrete samples made with constant aggregate content but with different compressive strengths. The preliminary results show that using coupling materials (both solid and a range of liquid substances) has an effect on the pulse velocity measured in a given concrete. The effect varies depending on the material used. The UPV measurements with solid coupling were higher than these from the liquid coupling at all strength levels. The tests using couplants generally recorded lower UPV values than the conventional test, except when carbon fiber composite was used, which retuned higher values. Analysis of variances (ANOVA) was performed to confirm that there are statistically significant differences between the measurements recorded using a conventional system and a coupled system.
Abstract: Makishima and Mackenzie model was used to
simulation of acoustic properties (longitudinal and shear ultrasonic
wave velocities, elastic moduli theoretically for many tellurite and
borate glasses. The model was proposed mainly depending on the
values of the experimentally measured density, which are obtained
before. In this search work, we are trying to obtain the values of
densities of amorphous glasses (as the density depends on the
geometry of the network structure of these glasses). In addition, the
problem of simulating the slope of linear regression between the
experimentally determined bulk modulus and the product of packing
density and experimental Young's modulus, were solved in this
search work. The results showed good agreement between the
experimentally measured values of densities and both ultrasonic wave
velocities, and those theoretically determined.
Abstract: Approximately 10,000 different types of dyes and
pigments are being used in various industrial applications yearly,
which include the textile and printing industries. However, these dyes
are difficult to degrade naturally once they enter the aquatic system.
Their high persistency in natural environment poses a potential health
hazard to all form of life. Hence, there is a need for alternative dye
removal strategy in the environment via bioremediation. In this study,
fungi laccase is investigated via commercial agar dyes plates and
submerged fermentation to explore the application of fungi laccase in
textile dye wastewater treatment. Two locally isolated basidiomycetes
were screened for laccase activity using media added with commercial
dyes such as 2, 2-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid
(ABTS), guaiacol and Remazol Brillant Blue R (RBBR). Isolate TBB3
(1.70±0.06) and EL2 (1.78±0.08) gave the highest results for ABTS
plates with the appearance of greenish halo on around the isolates.
Submerged fermentation performed on Isolate TBB3 with the
productivity 3.9067 U/ml/day, whereas the laccase activity for Isolate
EL2 was much lower (0.2097 U/ml/day). As isolate TBB3 showed
higher laccase production, it was subjected to molecular
characterization by DNA isolation, PCR amplification and sequencing
of ITS region of nuclear ribosomal DNA. After being compared with
other sequences in National Center for Biotechnology Information
(NCBI database), isolate TBB3 is probably from species Trametes
hirsutei. Further research work can be performed on this isolate by
upscale the production of laccase in order to meet the demands of the
requirement for higher enzyme titer for the bioremediation of textile
dyes.
Abstract: The Institutional Sustainability Performance (ISP) of State Universities and Colleges (SUCs) in the Philippines reveals the level of compliance and fidelity of the latter to the mandates of the state. This performance evaluation procedure aims to perpetually monitor and sustain the quality of services provided by the state institutions in the country. Importantly, the SUC level rating is one of the key indicators of the merit system adopted by the state to give incentives to government institutions. With the crucial role of the ISP and SUC level in the performance of an institution and in sustaining quality assurance, this study theorized that the top managers’ capacity to influence is the critical factor in meeting the expectations of the state. This study assessed the top managers’ capacity to influence. The hypothesis in this study proved that leadership style of top managers has significant relationship to the managers’ capacity to influence for institutional sustainability performance. Thus, the subjects of this study were restricted only to the State Universities and Colleges (SUC) that qualified in the top 20 Institutional Sustainability Performance; the digital governance performance, and the SUC leveling status nationwide. The top managers and their subordinates with doctorate of Bulacan State University and Bataan Peninsula State University whose programs have been consistently submitted to accreditation and were ranked Levels III and IV were subjected and participated to the study. This study assessed the top managers’ capacity to influence. The hypothesis in this study proved that leadership style of top managers has significant relationship to the managers’ capacity to influence for institutional sustainability performance. Thus, the subjects of this study were restricted only to the State Universities and Colleges (SUC) that qualified in the top 20 Institutional Sustainability Performance; the digital governance performance, and the SUC leveling status nationwide. The top managers and their subordinates with doctorate of Bulacan State University and Bataan Peninsula State University whose programs have been consistently submitted to accreditation and were ranked Levels III and IV were subjected and participated to the study.
Abstract: To focus on the vibration mode of a cone loudspeaker,
which acts as an electroacoustic transducer, excitation experiments
were performed using two types of loudspeaker units: one employing
an impulse hammer and the other a sweep signal. The on-axis sound
pressure frequency properties of the loudspeaker were evaluated, and
the characteristic properties of the loudspeakers were successfully
determined in both excitation experiments. Moreover, under
conditions identical to the experiment conditions, a coupled analysis of
the vibration-acoustics of the cone loudspeaker was performed using
an acoustic analysis software program that considers the impact of
damping caused by air viscosity. The result of sound pressure
frequency properties with the numerical analysis are the most closely
match that measured in the excitation experiments over a wide range
of frequency bands.
Abstract: Green chemistry for plant extraction of active principles is the main interest of many researchers concerned with climate change. While classical organic solvents are detrimental to our environment, greener alternatives to ionic liquids are very promising for sustainable organic chemistry. This study focused on the determination of functional groups observed in the main constituents from the ionic liquid extracts of Coleus aromaticus Benth leaves using FT-IR Spectroscopy. Moreover, this research aimed to determine the best ionic liquid that can separate functionalized plant constituents from the leaves Coleus aromaticus Benth using Fourier Transform Infrared Spectroscopy. Coleus aromaticus Benth leaf extract in different ionic liquids, elucidated pharmacologically important functional groups present in major constituents of the plant, namely, rosmarinic acid, caffeic acid and chlorogenic acid. In connection to distinctive appearance of functional groups in the spectrum and highest % transmittance, potassium chloride-glycerol is the best ionic liquid for green extraction.
Abstract: The present paper examines the impact noise
transmission through some floor building assemblies. The Acoubat
software numerical simulation has been used to simulate the impact
noise transmission through different floor configurations used in
Algerian construction mode. The results are compared with the
available measurements. We have developed two experimental
methods, i) field method, and ii) laboratory method using Brüel and
Kjær equipments. The results show that the different cases of floor
configurations need some improvement to ensure the acoustic
comfort in the receiving apartment. The recommended value of the
impact sound level in the receiving room should not exceed 58 dB.
The important results obtained in this paper can be used as platform
to improve the Algerian building acoustic regulation aimed at the
construction of the multi-storey residential building.
Abstract: The source of the jet noise is generated by rocket exhaust plume during rocket engine testing. A domain decomposition approach is applied to the jet noise prediction in this paper. The aerodynamic noise coupling is based on the splitting into acoustic sources generation and sound propagation in separate physical domains. Large Eddy Simulation (LES) is used to simulate the supersonic jet flow. Based on the simulation results of the flow-fields, the jet noise distribution of the sound pressure level is obtained by applying the Ffowcs Williams-Hawkings (FW-H) acoustics equation and Fourier transform. The calculation results show that the complex structures of expansion waves, compression waves and the turbulent boundary layer could occur due to the strong interaction between the gas jet and the ambient air. In addition, the jet core region, the shock cell and the sound pressure level of the gas jet increase with the nozzle size increasing. Importantly, the numerical simulation results of the far-field sound are in good agreement with the experimental measurements in directivity.
Abstract: Thoracotomy is a great surgery that has serious pulmonary complications, so purpose of this study was to determine the response of diaphragmatic excursion to inspiratory muscle trainer post thoracotomy. Thirty patients of both sexes (16 men and 14 women) with age ranged from 20 to 40 years old had done thoracotomy participated in this study. The practical work was done in cardiothoracic department, Kasr-El-Aini hospital at faculty of medicine for individuals 3 days Post operatively. Patients were assigned into two groups: group A (study group) included 15 patients (8 men and 7 women) who received inspiratory muscle training by using inspiratory muscle trainer for 20 minutes and routine chest physiotherapy (deep breathing, cough and early ambulation) twice daily, 3 days per week for one month. Group B (control group) included 15 patients (8 men and 7 women) who received the routine chest physiotherapy only (deep breathing, cough and early ambulation) twice daily, 3 days per week for one month. Ultrasonography was used to evaluate the changes in diaphragmatic excursion before and after training program. Statistical analysis revealed a significant increase in diaphragmatic excursion in the study group (59.52%) more than control group (18.66%) after using inspiratory muscle trainer post operatively in patients post thoracotomy. It was concluded that the inspiratory muscle training device increases diaphragmatic excursion in patients post thoracotomy through improving inspiratory muscle strength and improving mechanics of breathing and using of inspiratory muscle trainer as a method of physical therapy rehabilitation to reduce post-operative pulmonary complications post thoracotomy.
Abstract: The construction of most coastal infrastructure developments around the world are usually made considering wave height, current velocities and river discharges; however, little effort has been paid to surveying sediment transport during dredging or the modification to currents outside the ports or marinas during and after the construction. This study shows a complete survey during the construction of one of the largest ports of the Gulf of Mexico. An anchored Acoustic Doppler Current Velocity profiler (ADCP), a towed ADCP and a combination of model outputs were used at the Veracruz port construction in order to describe the hourly sediment transport and current modifications in and out of the new port. Owing to the stability of the system the new port was construction inside Vergara Bay, a low wave energy system with a tidal range of up to 0.40 m. The results show a two-current system pattern within the bay. The north side of the bay has an anticyclonic gyre, while the southern part of the bay shows a cyclonic gyre. Sediment transport trajectories were made every hour using the anchored ADCP, a numerical model and the weekly data obtained from the towed ADCP within the entire bay. The sediment transport trajectories were carefully tracked since the bay is surrounded by coral reef structures which are sensitive to sedimentation rate and water turbidity. The survey shows that during dredging and rock input used to build the wave breaker sediments were locally added (< 2500 m2) and local currents disperse it in less than 4 h. While the river input located in the middle of the bay and the sewer system plant may add more than 10 times this amount during a rainy day or during the tourist season. Finally, the coastal line obtained seasonally with a drone suggests that the southern part of the bay has not been modified by the construction of the new port located in the northern part of the bay, owing to the two subsystem division of the bay.
Abstract: Cochlear Implantation (CI) which became a routine
procedure for the last decades is an electronic device that provides a
sense of sound for patients who are severely and profoundly deaf.
The optimal success of this implantation depends on the electrode
technology and deep insertion techniques. However, this manual
insertion procedure may cause mechanical trauma which can lead to
severe destruction of the delicate intracochlear structure.
Accordingly, future improvement of the cochlear electrode implant
insertion needs reduction of the excessive force application during
the cochlear implantation which causes tissue damage and trauma.
This study is examined tool-tissue interaction of large prototype scale
digit embedded with distributive tactile sensor based upon cochlear
electrode and large prototype scale cochlea phantom for simulating
the human cochlear which could lead to small scale digit
requirements. The digit, distributive tactile sensors embedded with
silicon-substrate was inserted into the cochlea phantom to measure
any digit/phantom interaction and position of the digit in order to
minimize tissue and trauma damage during the electrode cochlear
insertion. The digit have provided tactile information from the digitphantom
insertion interaction such as contact status, tip penetration,
obstacles, relative shape and location, contact orientation and
multiple contacts. The tests demonstrated that even devices of such a
relative simple design with low cost have potential to improve
cochlear implant surgery and other lumen mapping applications by
providing tactile sensory feedback information and thus controlling
the insertion through sensing and control of the tip of the implant
during the insertion. In that approach, the surgeon could minimize the
tissue damage and potential damage to the delicate structures within
the cochlear caused by current manual electrode insertion of the
cochlear implantation. This approach also can be applied to other
minimally invasive surgery applications as well as diagnosis and path
navigation procedures.
Abstract: Thermoacoustic refrigerator is a cooling device which
uses the acoustic waves to produce the cooling effect. The aim of this
paper is to explore the experimental and numerical feasibility of a
standing-wave thermoacoustic refrigerator. The effects of the stack
length, position of stack and operating frequency on the cooling
performance are carried out. The circular pore stacks are tested under
the atmospheric pressure. A low-cost loudspeaker is used as an
acoustic driver. The results show that the location of stack installed in
resonator tube has a greater effect on the cooling performance, than
the stack length and operating frequency, respectively. The
temperature difference across the ends of stack can be generated up
to 13.7°C, and the temperature of cold-end is dropped down by 5.3°C
from the ambient temperature.
Abstract: Monitoring the conditions of rotating machinery, such
as bearings, is important in order to improve the stability of work.
Acoustic Emission (AE) and vibration analysis are some of the most
accomplished techniques used for this purpose. Acoustic emission
has the ability to detect the initial phase of component degradation.
Moreover, it has been observed that vibration analysis is not as
successful at low rotational speeds (below 100 rpm). This because the
energy generated within this speed region is not detectable using
conventional vibration. From this perspective, this paper has
presented a brief review of using acoustic emission techniques for
monitoring bearing conditions.