Abstract: In this research the Preparation of Land use map of
scanner LISS III satellite data, belonging to the IRS in the Aghche
region in Isfahan province, is studied carefully. For this purpose, the
IRS satellite images of August 2008 and various land preparation
uses in region including rangelands, irrigation farming, dry farming,
gardens and urban areas were separated and identified. Therefore, the
GPS and Erdas Imaging software were used and three methods of
Maximum Likelihood, Mahalanobis Distance and Minimum Distance
were analyzed. In each of these methods, matrix error and Kappa
index were calculated and accuracy of each method, based on
percentages: 53.13, 56.64 and 48.44, were obtained respectively.
Considering the low accuracy of these methods in separation of land
preparation use, the visual interpretation of the map was used.
Finally, regional visits of 150 points were noted at random and no
error was observed. It shows that the map prepared by visual
interpretation is in high accuracy. Although the probable errors due
to visual interpretation and geometric correction might happen but
the desired accuracy of the map which is more than 85 percent is
reliable.
Abstract: In this paper, we investigate multihop polling and data gathering schemes in layered sensor networks in order to extend the life time of the networks. A network consists of three layers. The lowest layer contains sensors. The middle layer contains so called super nodes with higher computational power, energy supply and longer transmission range than sensor nodes. The top layer contains a sink node. A node in each layer controls a number of nodes in lower layer by polling mechanism to gather data. We will present four types of data gathering schemes: intermediate nodes do not queue data packet, queue single packet, queue multiple packets and aggregate data, to see which data gathering scheme is more energy efficient for multihop polling in layered sensor networks.
Abstract: Among various testing methodologies, Built-in Self-
Test (BIST) is recognized as a low cost, effective paradigm. Also,
full adders are one of the basic building blocks of most arithmetic
circuits in all processing units. In this paper, an optimized testable 2-
bit full adder as a test building block is proposed. Then, a BIST
procedure is introduced to scale up the building block and to generate
a self testable n-bit full adders. The target design can achieve 100%
fault coverage using insignificant amount of hardware redundancy.
Moreover, Overall test time is reduced by utilizing polymorphic
gates and also by testing full adder building blocks in parallel.
Abstract: In this article, we synthesize a novel chitosan -based
superabsorbent hydrogel via graft copolymerization of mixtures
acrylic acid (AA) and N-vinyl pyrollidon onto chitosan backbones.
The polymerization reaction was carried out in an aqueous medium
and in the presence of ammonium persulfate (APS) as an initiator and
N,N'-methylene bisacrylamide (MBA) as a crosslinker.The hydrogel
structures were confirmed by FTIR spectroscopy. The swelling
behavior of these absorbent polymers was also investigated in
various salt solutions. Results indicated that the swelling capacity
decreased with an increase in the ionic strength of the swelling
medium. Furthermore, the swelling of superabsorbing hydrogels was
examined in solutions with pH values ranging between 1.0 and 13.0.
It showed a reversible pH-responsive behavior at pHs 2.0 and 8.0.
This on-off switching behavior makes the synthesized hydrogels as
an excellent candidate for controlled delivery of bioactive agents.
Abstract: The purpose of this paper is to present a Dynamic
Time Warping technique which reduces significantly the data
processing time and memory size of multi-dimensional time series
sampled by the biometric smart pen device BiSP. The acquisition
device is a novel ballpoint pen equipped with a diversity of sensors
for monitoring the kinematics and dynamics of handwriting
movement. The DTW algorithm has been applied for time series
analysis of five different sensor channels providing pressure,
acceleration and tilt data of the pen generated during handwriting on
a paper pad. But the standard DTW has processing time and memory
space problems which limit its practical use for online handwriting
recognition. To face with this problem the DTW has been applied to
the sum of the five sensor signals after an adequate down-sampling
of the data. Preliminary results have shown that processing time and
memory size could significantly be reduced without deterioration of
performance in single character and word recognition. Further
excellent accuracy in recognition was achieved which is mainly due
to the reduced dynamic time warping RDTW technique and a novel
pen device BiSP.
Abstract: This paper describes a concept of stereotype student
model in adaptive knowledge acquisition e-learning system. Defined
knowledge stereotypes are based on student's proficiency level and
on Bloom's knowledge taxonomy. The teacher module is responsible
for the whole adaptivity process: the automatic generation of
courseware elements, their dynamic selection and sorting, as well as
their adaptive presentation using templates for statements and
questions. The adaptation of courseware is realized according to
student-s knowledge stereotype.
Abstract: Neonatal lupus erythematous (NLE) is a rare disease marked by clinical characteristic and specific maternal autoantibody. Many cutaneous, cardiac, liver, and hematological manifestations could happen with affect of one organ or multiple. In this case, both babies were premature, low birth weight (LBW), small for gestational age (SGA) and born through caesarean section from a systemic lupus erythematous (SLE) mother. In the first case, we found a baby girl with dyspnea and grunting. Chest X ray showed respiratory distress syndrome (RDS) great I and echocardiography showed small atrial septal defect (ASD) and ventricular septal defect (VSD). She also developed anemia, thrombocytopenia, elevated C-reactive protein, hypoalbuminemia, increasing coagulation factors, hyperbilirubinemia, and positive blood culture of Klebsiella pneumonia. Anti-Ro/SSA and Anti-nRNP/sm were positive. Intravenous fluid, antibiotic, transfusion of blood, thrombocyte concentrate, and fresh frozen plasma were given. The second baby, male presented with necrotic tissue on the left ear and skin rashes, erythematous macula, athropic scarring, hyperpigmentation on all of his body with various size and facial haemorrhage. He also suffered from thrombocytopenia, mild elevated transaminase enzyme, hyperbilirubinemia, anti-Ro/SSA was positive. Intravenous fluid, methyprednisolone, intravenous immunoglobulin (IVIG), blood, and thrombocyte concentrate transfution were given. Two cases of neonatal lupus erythematous had been presented. Diagnosis based on clinical presentation and maternal auto antibody on neonate. Organ involvement in NLE can occur as single or multiple manifestations.
Abstract: This paper presents one comprehensive modelling approach for maintenance scheduling problem of thermal power units in competitive market. This problem is formulated as a 0/1 mixedinteger linear programming model. Model incorporates long-term bilateral contracts with defined profiles of power and price, and weekly forecasted market prices for market auction. The effectiveness of the proposed model is demonstrated through case study with detailed discussion.
Abstract: Dehydration process was carried out for tomato slices of var. Avinash after giving different pre-treatments such as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl). Untreated samples served as control. Solar drier and continuous conveyor (tunnel) drier were used for dehydration. Quality characteristics of tomato slices viz. moisture content, sugar, titratable acidity, lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning as affected by dehydration process were studied. Storage study was also carried out for a period of six months for tomato powder packed into different types of packaging materials viz. metalized polyester (MP) film and low density poly ethylene (LDPE). Changes in lycopene content and non-enzymatic browning (NEB) were estimated during storage at room temperature. Pretreatment of 5 mm thickness of tomato slices with calcium chloride in combination with potassium metabisulphite and drying using a tunnel drier with subsequent storage of product in metalized polyester bags was selected as the best process.
Abstract: The objective of the paper was to understand the use
of an important element of design, namely color in a Semiotic
system. Semiotics is the study of signs and sign processes, it is often
divided into three branches namely (i) Semantics that deals with the
relation between signs and the things to which they refer to mean, (ii)
Syntactics which addresses the relations among signs in formal
structures and (iii) Pragmatics that relates between signs and its
effects on they have on the people who use them to create a plan for
an object or a system referred to as design. Cubism with its versatility
was the key design tool prevalent across the 20th century. In order to
analyze the user's understanding of interaction and appreciation of
color through the movement of Cubism, an exercise was undertaken
in Dept. of Design, IIT Guwahati. This included tasks to design a
composition using color and sign process to the theme 'Between the
Lines' on a given tessellation where the users relate their work to the
world they live in, which in this case was the college campus of IIT
Guwahati. The findings demonstrate impact of the key design
element color on the principles of visual perception based on image
analysis of specific compositions.
Abstract: Fecal sterol has been proposed as a chemical indicator
of human fecal pollution even when fecal coliform populations have
diminished due to water chlorination or toxic effects of industrial
effluents. This paper describes an improved derivatization procedure
for simultaneous determination of four fecal sterols including
coprostanol, epicholestanol, cholesterol and cholestanol using gas
chromatography-mass spectrometry (GC-MS), via optimization study
on silylation procedures using N-O-bis
(trimethylsilyl)-trifluoroacetamide (BSTFA), and
N-(tert-butyldimethylsilyl)-N-methyltrifluoroacetamide
(MTBSTFA), which lead to the formation of trimethylsilyl (TMS) and
tert-butyldimethylsilyl (TBS) derivatives, respectively. Two
derivatization processes of injection-port derivatization and water bath
derivatization (60 oC, 1h) were inspected and compared. Furthermore,
the methylation procedure at 25 oC for 2h with
trimethylsilydiazomethane (TMSD) for fecal sterols analysis was also
studied. It was found that most of TMS derivatives demonstrated the
highest sensitivities, followed by methylated derivatives. For BSTFA
or MTBSTFA derivatization processes, the simple injection-port
derivatization process could achieve the same efficiency as that in the
tedious water bath derivatization procedure.
Abstract: An accurate procedure to determine free vibrations of
beams and plates is presented.
The natural frequencies are exact solutions of governing vibration
equations witch load to a nonlinear homogeny system.
The bilinear and linear structures considered simulate a bridge.
The dynamic behavior of this one is analyzed by using the theory of
the orthotropic plate simply supported on two sides and free on the
two others. The plate can be excited by a convoy of constant or
harmonic loads. The determination of the dynamic response of the
structures considered requires knowledge of the free frequencies and
the shape modes of vibrations. Our work is in this context. Indeed,
we are interested to develop a self-consistent calculation of the Eigen
frequencies.
The formulation is based on the determination of the solution of
the differential equations of vibrations. The boundary conditions
corresponding to the shape modes permit to lead to a homogeneous
system. Determination of the noncommonplace solutions of this
system led to a nonlinear problem in Eigen frequencies.
We thus, develop a computer code for the determination of the
eigenvalues. It is based on a method of bisection with interpolation
whose precision reaches 10 -12. Moreover, to determine the
corresponding modes, the calculation algorithm that we develop uses
the method of Gauss with a partial optimization of the "pivots"
combined with an inverse power procedure. The Eigen frequencies
of a plate simply supported along two opposite sides while
considering the two other free sides are thus analyzed. The results
could be generalized with the case of a beam by regarding it as a
plate with low width.
We give, in this paper, some examples of treated cases. The
comparison with results presented in the literature is completely
satisfactory.
Abstract: Fuller’s earth is a fine-grained, naturally occurring substance that has a substantial ability to adsorb impurities. In the present study Fuller’s earth has been characterized and used for the removal of Pb(II) from aqueous solution. The effect of various physicochemical parameters such as pH, adsorbent dosage and shaking time on adsorption were studied. The result of the equilibrium studies showed that the solution pH was the key factor affecting the adsorption. The optimum pH for adsorption was 5. Kinetics data for the adsorption of Pb(II) was best described by pseudo-second order model. The effective diffusion co-efficient for Pb(II) adsorption was of the order of 10-8 m2/s. The adsorption data for metal adsorption can be well described by Langmuir adsorption isotherm. The maximum uptake of metal was 103.3 mg/g of adsorbent. Mass transfer analysis was also carried out for the adsorption process. The values of mass transfer coefficients obtained from the study indicate that the velocity of the adsorbate transport from bulk to the solid phase was quite fast. The mean sorption energy calculated from Dubinin-Radushkevich isotherm indicated that the metal adsorption process was chemical in nature.
Abstract: Planar systems of electrodes arranged on both sides of dielectric piezoelectric layer are applied in numerous transducers. They are capable of electronic beam-steering of generated wave both in azimuth and elevation. The wave-beam control is achieved by addressable driving of two-dimensional transducer through proper voltage supply of electrodes on opposite surfaces of the layer. In this paper a semi-analytical method of analysis of the considered transducer is proposed, which is a generalization of the well-known BIS-expansion method. It was earlier exploited with great success in the theory of interdigital transducers of surface acoustic waves, theory of elastic wave scattering by cracks and certain advanced electrostatic problems. The corresponding nontrivial electrostatic problem is formulated and solved numerically.
Abstract: This research paper is based upon the simulation of
gradient of mathematical functions and scalar fields using MATLAB.
Scalar fields, their gradient, contours and mesh/surfaces are
simulated using different related MATLAB tools and commands for
convenient presentation and understanding. Different mathematical
functions and scalar fields are examined here by taking their
gradient, visualizing results in 3D with different color shadings and
using other necessary relevant commands. In this way the outputs of
required functions help us to analyze and understand in a better way
as compared to just theoretical study of gradient.
Abstract: A method based on the power series solution is proposed to solve the natural frequency of flapping vibration for the rotating inclined Euler beam with constant angular velocity. The vibration of the rotating beam is measured from the position of the corresponding steady state axial deformation. In this paper the governing equations for linear vibration of a rotating Euler beam are derived by the d'Alembert principle, the virtual work principle and the consistent linearization of the fully geometrically nonlinear beam theory in a rotating coordinate system. The governing equation for flapping vibration of the rotating inclined Euler beam is linear ordinary differential equation with variable coefficients and is solved by a power series with four independent coefficients. Substituting the power series solution into the corresponding boundary conditions at two end nodes of the rotating beam, a set of homogeneous equations can be obtained. The natural frequencies may be determined by solving the homogeneous equations using the bisection method. Numerical examples are studied to investigate the effect of inclination angle on the natural frequency of flapping vibration for rotating inclined Euler beams with different angular velocity and slenderness ratio.
Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: In this study, three strains of Vibrio parahaemolyticus
(690, BCRC 13023 and BCRC 13025) were subjected to acid
adaptation at pH 5.5 for 90 min. The survival of acid-adapted and
non-adapted V. parahaemolyticus strains under simulated gastric
condition and their protein expression profiles were investigated.
Results showed that acid adaptation increased the survival of the test
V. parahaemolyticus strains after exposure to simulated gastric juice
(pH 3). Additionally, acid adaptation also affected the protein
expression in these V. parahaemolyticus strains. Nine proteins,
identified as atpA, atpB, DnaK, GroEL, OmpU, enolase,
fructose-bisphosphate aldolase, phosphoglycerate kinase and
triosephosphate isomerase, were induced by acid adaptation in two or
three of the test strains. These acid-adaptive proteins may play
important regulatory roles in the acid tolerance response (ATR) of V.
parahaemolyticus.
Abstract: Dew harvesting needs only weak investment and
exploits a free, clean and inexhaustible energy. This study aims to
measure the relative contributions of dew and rain water in the
Mediterranean Dalmatian coast and islands of Croatia and determine
whether dew water is potable. Two sites were chosen, an open site on
the coast favourable to dew formation (Zadar) and a less favourable
site in a circus of mountains in Komiža (Vis Island). Between July
1st, 2003 and October 31st, 2006, dew hasbeen daily collected on a 1
m2 tilted (30°) test dew condenser together with ordinary
meteorological data (air temperature and relative humidity, cloud
coverage, windspeed and direction). The mean yearly cumulative
dew yields were found to be 20 mm (Zadar) and 9.3 mm (Komiža ).
During the dry season (May to October), monthly cumulative dew
water yield can represent up to 38% of water collected by rain fall. In
July 2003 and 2006, dew water represented about 120% of the
monthly cumulative rain water. Dew and rain water were analyzed in
Zadar. The corresponding parameters were measured: pH, electrical
conductivity, major anions (HCO3
-, Cl-, SO4
2-
, NO3
-
, ,) and major
cations (NH4
+, Na+, K+, Ca2+, Mg2+. Both dew and rain water are in
conformity with the WHO directives for potability except Mg2+.
Using existing roofs and refurbishing the abandoned impluviums to
permit dew collection could then provide a useful supplementary
amount of water, especially during the dry season.
Abstract: Functioning of a biometric system in large part
depends on the performance of the similarity measure function.
Frequently a generalized similarity distance measure function such as
Euclidian distance or Mahalanobis distance is applied to the task of
matching biometric feature vectors. However, often accuracy of a
biometric system can be greatly improved by designing a customized
matching algorithm optimized for a particular biometric application.
In this paper we propose a tailored similarity measure function for
behavioral biometric systems based on the expert knowledge of the
feature level data in the domain. We compare performance of a
proposed matching algorithm to that of other well known similarity
distance functions and demonstrate its superiority with respect to the
chosen domain.