Experiment Study on the Influence of Tool Materials on the Drilling of Thick Stacked Plate of 2219 Aluminum Alloy

The drilling and riveting processes are widely used in the assembly of carrier rocket, which makes the efficiency and quality of drilling become the important factor affecting the assembly process. According to the problem existing in the drilling of thick stacked plate (thickness larger than 10mm) of carrier rocket, such as drill break, large noise and burr etc., experimental study of the influence of tool material on the drilling was carried out. The cutting force was measured by a piezoelectric dynamometer, the aperture was measured with an outline projector, and the burr is observed and measured by a digital stereo microscope. Through the measurement, the effects of tool material on the drilling were analyzed from the aspects of drilling force, diameter, and burr. The results show that, compared with carbide drill and coated carbide one, the drilling force of high speed steel is larger. But, the application of high speed steel also has some advantages, e.g. a higher number of hole can be obtained, the height of burr is small, the exit is smooth and the slim burr is less, and the tool experiences wear but not fracture. Therefore, the high speed steel tool is suitable for the drilling of thick stacked plate of 2219 Aluminum alloy.





References:
[1] J. Kim, S. Min, D. A. Dornfeld. “Optimization and control of drilling burr formation of AISI 304L and AISI 4118 based on drilling burr control charts”, Journal of Machine Tools & Manufacture, No. 41, pp. 923-936, July. 2001.
[2] C.Hellstern, “Investigation of interlayer burr formation in the drilling of stacked aluminum sheets”, Master Thesis, Georgia Institute of Technology, 2009.
[3] S. N. Melkote, T. R. Newton, C.Hellstern, J. B. Morehouse, S. Turner. “Interfacial burr formation in drilling of stacked aerospace materials, Burrs Analysis”, Control and Removal, Vol. 41, No.5, pp. 89-98, April, 2010.
[4] S. S. Bi, J. Liang. “Experimental studies and optimization of process parameters for burrs in dry drilling of stacked metal materials”,Int J Adv. Manuf. Technol, Vol.53, No.9, pp. 867-76, September, 2011.
[5] T. Rajmohan, K. Palanikumar, M. Kathirvel. “Optimization of machining parameters in drilling hybrid aluminium metal matrix composites”, Trans. Nonferrous Met. Soc. China, Vol. 32, No. 22, pp. 1286-1297, October,2012.
[6] X. H. Zhang, H. H. Zheng. “Experimental studies of process parameters for burrs in dry drilling of stacked metal materials”, Modern Manufacturing Engineering, No. 10, pp. 79-82, May,2011.
[7] X. X. Xu, Y. X. Hu, Z. Q. Yao. “Experimental Studies of Process Parameters for Interfacial Burr in Dry Drilling of Stacked Aluminum Alloy Sheets”, Modular Machine Tool & Automatic Manufacturing Technique, No. 12, pp. 109-112, August, 2012.
[8] J. Liang. “The formation and effect of the interlayer gap in dry drilling of stacked metal materials”, Int. J. Adv. Manuf. Technol, Vol. 69, No. 5-8, pp.1263–1272, November,2013.
[9] Y. Li, Y.X. Hu, Z. Q. Yao, “Experimental Investigation of the effect of Clamping force on the interlayer drilling burr of stacked aluminum alloy sheets”, Modular Machine Tool & Automatic Manufacturing Technique, Vol. 2, No. 2, pp. 111-113, December,2014.
[10] H. Zhang, L. Qiao, H. J. Guo,“Optimization of process parameters for automatic hole making of stacked components of difficult to machine material”, Conference of China Aviation Science and Technology, pp. 223-226, October, 2015.
[11] Z. J. Lu. “Study of One-Side Pressed Drilling Process of Aluminum Alloy Thin-Walled Laminated Structure”, Aeronautical Manufacturing Technology, Vol. S2, pp. 152-156, May, 2015.
[12] Y. Gao, D. Wu, C. Nan, X. Ma, Y. Dong. “The interlayer gap and non-coaxiality in stack drilling”, International Journal of Machine Tools & Manufacturing, Vol.18, No. 99. pp. 68-76, November,2015.
[13] Y. Bu, W. Tian, W. H. Liao, J. Hu, X. Sun. “Investigation of correlation between interlayer gap and burr height in drilling of stacked Al-7475 materials”, Proc. IMechE. Part B: Journal of Engineering Manufacture, 2015, In press.
[14] H. Wang, X. Sun, J.Hu. “Experimental study on interlayer burr of stacked material under different compression conditions”, Mechanical Manufacturing, Vol. 54, No. 1, pp. 51-54, August,2016.
[15] W. Tian, J. Hu, W. H. Liao, Y. Bu, L. Zhang. “Formation of interlayer gap and control of interlayer burr in dry drilling of stacked aluminum alloy plates”, Chinese Journal of Aeronautics, 2016, In press.
[16] H. Su, X. H. Ma, J. Wang, “Experimental Studies of Automatic Drilling on the Large Rocket Panel Components”, Aviation Precision Manufacturing Technology, Vol. 53, No. 1, pp. 26-39,July,2017.
[17] C. Y. Lei, C. Li, Y. B. Bi, J. X. Li. “The optimal clamping force option for robotic drilling of stacked aluminum sheets based on shell theory”, Advances in Mechanical Engineering, Vol. 9, No. 3, pp. 1-9, December, 2017.