Abstract: Scale Time Offset Robust Modulation (STORM) [1]–
[3] is a high bandwidth waveform design that adds time-scale
to embedded reference modulations using only time-delay [4]. In
an environment where each user has a specific delay and scale,
identification of the user with the highest signal power and that
user-s phase is facilitated by the STORM processor. Both of these
parameters are required in an efficient multiuser detection algorithm.
In this paper, the STORM modulation approach is evaluated with
a direct sequence spread quadrature phase shift keying (DS-QPSK)
system. A misconception of the STORM time scale modulation is that
a fine temporal resolution is required at the receiver. STORM will
be applied to a QPSK code division multiaccess (CDMA) system
by modifying the spreading codes. Specifically, the in-phase code
will use a typical spreading code, and the quadrature code will
use a time-delayed and time-scaled version of the in-phase code.
Subsequently, the same temporal resolution in the receiver is required
before and after the application of STORM. In this paper, the bit error
performance of STORM in a synchronous CDMA system is evaluated
and compared to theory, and the bit error performance of STORM
incorporated in a single user WCDMA downlink is presented to
demonstrate the applicability of STORM in a modern communication
system.
Abstract: Wireless Sensor Networks (WSN) are emerging
because of the developments in wireless communication technology and miniaturization of the hardware. WSN consists of a large number of low-cost, low-power, multifunctional sensor nodes to monitor physical conditions, such as temperature, sound, vibration, pressure,
motion, etc. The MAC protocol to be used in the sensor networks must be energy efficient and this should aim at conserving the energy during its operation. In this paper, with the focus of analyzing the
MAC protocols used in wireless Adhoc networks to WSN, simulation
experiments were conducted in Global Mobile Simulator
(GloMoSim) software. Number of packets sent by regular nodes, and received by sink node in different deployment strategies, total energy
spent, and the network life time have been chosen as the metric for comparison. From the results of simulation, it is evident that the IEEE 802.11 protocol performs better compared to CSMA and MACA protocols.
Abstract: The localized corrosion behavior of laser surface
melted 304L austenitic stainless steel was studied by
potentiodynamic polarization test. The extent of improvement in
corrosion resistance was governed by the preferred orientation and
the percentage of delta ferrite present on the surface of the laser
melted sample. It was established by orientation imaging microscopy
that the highest pitting potential value was obtained when grains were
oriented in the most close- packed [101] direction compared to the
random distribution of the base metal and other laser surface melted
samples oriented in [001] direction. The sample with lower
percentage of ferrite had good pitting resistance.
Abstract: The present study was conducted to investigate the
response of plants exposed to lignite-based thermal power plant
emission. For this purpose, five plant species were collected from 1.0
km distance (polluted site) and control plants were collected from
20.0 km distance (control site) to thermal power plant. The common
tree species Cassia siamea Lamk., Polyalthia longifolia. Sonn,
Acacia longifolia (Andrews) Wild., Azadirachta indica A.Juss, Ficus
religiosa L. were selected as test plants. Photosynthetic pigments
changes (chlorophyll a, chlorophyll b and carotenoids) and rubisco
enzyme modifications were studied. Reduction was observed in the
photosynthetic pigments of plants growing in polluted site and also
large sub unit of the rubisco enzyme was degraded in Azadirachta
indica A. Juss collected from polluted site.
Abstract: The characterization of κ-carrageenan could provide a
better understanding of its functions in biological, medical and
industrial applications. Chemical and physical analyses of
carrageenan from seaweeds, Euchema cottonii L., were done to offer
information on its properties and the effects of Co-60 γ-irradiation on
its thermochemical characteristics. The structural and morphological
characteristics of κ-carrageenan were determined using scanning
electron microscopy (SEM) while the composition, molecular weight
and thermal properties were determined using attenuated total
reflectance Fourier transform infrared spectroscopy (ATR-FTIR), gel
permeation chromatography (GPC), thermal gravimetric analysis
(TGA) and differential scanning calorimetry (DSC). Further chemical
analysis was done using hydrogen-1 nuclear magnetic resonance (1H
NMR) and functional characteristics in terms of biocompatibility
were evaluated using cytotoxicity test.
Abstract: This paper presents a genetic algorithm based
approach for solving security constrained optimal power flow
problem (SCOPF) including FACTS devices. The optimal location of
FACTS devices are identified using an index called overload index
and the optimal values are obtained using an enhanced genetic
algorithm. The optimal allocation by the proposed method optimizes
the investment, taking into account its effects on security in terms of
the alleviation of line overloads. The proposed approach has been
tested on IEEE-30 bus system to show the effectiveness of the
proposed algorithm for solving the SCOPF problem.
Abstract: Tanzania is a developing country, which significantly lags behind the rest of the world in information communications technology (ICT), especially for the Internet. Internet connectivity to the rest of the world is via expensive satellite links, thus leaving the majority of the population unable to access the Internet due to the high cost. This paper introduces the concept of an optical WDM network for Internet infrastructure in Tanzania, so as to reduce Internet connection costs, and provide Internet access to the majority of people who live in both urban and rural areas. We also present a proposed optical WDM network, which mitigates the effects of system impairments, and provide simulation results to show that the data is successfully transmitted over a longer distance using a WDM network.
Abstract: How to efficiently assign system resource to route the
Client demand by Gateway servers is a tricky predicament. In this
paper, we tender an enhanced proposal for autonomous recital of
Gateway servers under highly vibrant traffic loads. We devise a
methodology to calculate Queue Length and Waiting Time utilizing
Gateway Server information to reduce response time variance in
presence of bursty traffic.
The most widespread contemplation is performance, because
Gateway Servers must offer cost-effective and high-availability
services in the elongated period, thus they have to be scaled to meet
the expected load. Performance measurements can be the base for
performance modeling and prediction. With the help of performance
models, the performance metrics (like buffer estimation, waiting
time) can be determined at the development process.
This paper describes the possible queue models those can be
applied in the estimation of queue length to estimate the final value
of the memory size. Both simulation and experimental studies using
synthesized workloads and analysis of real-world Gateway Servers
demonstrate the effectiveness of the proposed system.
Abstract: A robust AUSM+ upwind discretisation scheme has been developed to simulate multiphase flow using consistent spatial discretisation schemes and a modified low-Mach number diffusion term. The impact of the selection of an interfacial pressure model has also been investigated. Three representative test cases have been simulated to evaluate the accuracy of the commonly-used stiffenedgas equation of state with respect to the IAPWS-IF97 equation of state for water. The algorithm demonstrates a combination of robustness and accuracy over a range of flow conditions, with the stiffened-gas equation tending to overestimate liquid temperature and density profiles.
Abstract: A social network is a set of people or organization or other social entities connected by some form of relationships. Analysis of social network broadly elaborates visual and mathematical representation of that relationship. Web can also be considered as a social network. This paper presents an innovative approach to analyze a social network using a variant of existing ant colony optimization algorithm called as Clever Ant Colony Metaphor. Experiments are performed and interesting findings and observations have been inferred based on the proposed model.
Abstract: The exhaustive quality control is becoming more and
more important when commercializing competitive products in the
world's globalized market. Taken this affirmation as an undeniable
truth, it becomes critical in certain sector markets that need to offer
the highest restrictions in quality terms. One of these examples is the
percussion cap mass production, a critical element assembled in
firearm ammunition. These elements, built in great quantities at a
very high speed, must achieve a minimum tolerance deviation in
their fabrication, due to their vital importance in firing the piece of
ammunition where they are built in. This paper outlines a machine
vision development for the 100% inspection of percussion caps
obtaining data from 2D and 3D simultaneous images. The acquisition
speed and precision of these images from a metallic reflective piece
as a percussion cap, the accuracy of the measures taken from these
images and the multiple fabrication errors detected make the main
findings of this work.
Abstract: This paper presents a highly efficient algorithm for detecting and tracking humans and objects in video surveillance sequences. Mean shift clustering is applied on backgrounddifferenced image sequences. For efficiency, all calculations are performed on integral images. Novel corresponding exponential integral kernels are introduced to allow the application of nonuniform kernels for clustering, which dramatically increases robustness without giving up the efficiency of the integral data structures. Experimental results demonstrating the power of this approach are presented.
Abstract: Cutting fluids, usually in the form of a liquid, are
applied to the chip formation zone in order to improve the cutting
conditions. Cutting fluid can be expensive and represents a biological
and environmental hazard that requires proper recycling and
disposal, thus adding to the cost of the machining operation. For
these reasons dry cutting or dry machining has become an
increasingly important approach; in dry machining no coolant or
lubricant is used. This paper discussed the effect of the dry cutting on
cutting force and tool life when machining aerospace materials
(Haynes 242) with using two different coated carbide cutting tools
(TiAlN and TiN/MT-TiCN/TiN). Response surface method (RSM)
was used to minimize the number of experiments. ParTiAlN Swarm
Optimisation (PSO) models were developed to optimize the
machining parameters (cutting speed, federate and axial depth) and
obtain the optimum cutting force and tool life. It observed that
carbide cutting tool coated with TiAlN performed better in dry
cutting compared with TiN/MT-TiCN/TiN. On other hand, TiAlN
performed more superior with using of 100 % water soluble coolant.
Due to the high temperature produced by aerospace materials, the
cutting tool still required lubricant to sustain the heat transfer from
the workpiece.
Abstract: One of the most basic functions of control engineers is
tuning of controllers. There are always several process loops in the
plant necessitate of tuning. The auto tuned Proportional Integral
Derivative (PID) Controllers are designed for applications where
large load changes are expected or the need for extreme accuracy and
fast response time exists. The algorithm presented in this paper is
used for the tuning PID controller to obtain its parameters with a
minimum computing complexity. It requires continuous analysis of
variation in few parameters, and let the program to do the plant test
and calculate the controller parameters to adjust and optimize the
variables for the best performance. The algorithm developed needs
less time as compared to a normal step response test for continuous
tuning of the PID through gain scheduling.
Abstract: Existing image-based virtual reality applications
allow users to view image-based 3D virtual environment in a more
interactive manner. User could “walkthrough"; looks left, right, up
and down and even zoom into objects in these virtual worlds of
images. However what the user sees during a “zoom in" is just a
close-up view of the same image which was taken from a distant.
Thus, this does not give the user an accurate view of the object from
the actual distance. In this paper, a simple technique for zooming in
an object in a virtual scene is presented. The technique is based on
the 'hotspot' concept in existing application. Instead of navigation
between two different locations, the hotspots are used to focus into
an object in the scene. For each object, several hotspots are created.
A different picture is taken for each hotspot. Each consecutive
hotspot created will take the user closer to the object. This will
provide the user with a correct of view of the object based on his
proximity to the object. Implementation issues and the relevance of
this technique in potential application areas are highlighted.
Abstract: This paper presents work characterizing finite element
performance boundaries within which live, interactive finite element
modeling is feasible on current and emerging systems. These results
are based on wide-ranging tests performed using a prototype finite
element program implemented specifically for this study, thereby enabling
the unified investigation of numerous direct and iterative solver
strategies and implementations in a variety of modeling contexts.
The results are intended to be useful for researchers interested in
interactive analysis by providing baseline performance estimates, to
give guidance in matching solution strategies to problem domains,
and to spur further work addressing the challenge of extending the
present boundaries.
Abstract: This paper presents the application of discrete-time
variable structure control with sliding mode based on the 'reaching
law' method for robust control of a 'simple inverted pendulum on
moving cart' - a standard nonlinear benchmark system. The
controllers designed using the above techniques are completely
insensitive to parametric uncertainty and external disturbance. The
controller design is carried out using pole placement technique to find
state feedback gain matrix , which decides the dynamic behavior
of the system during sliding mode. This is followed by feedback gain
realization using the control law which is synthesized from 'Gao-s
reaching law'. The model of a single inverted pendulum and the
discrete variable structure control controller are developed, simulated
in MATLAB-SIMULINK and results are presented. The response of
this simulation is compared with that of the discrete linear quadratic
regulator (DLQR) and the advantages of sliding mode controller over
DLQR are also presented
Abstract: The experiments were performed in a batch set up
under different concentrations of Cu (II) (0.2 g.l-1 to 0.9 g.l-1), pH (4-
6), temperatures (20oC – 40oC) with varying teak leaves powder (as
biosorbent) dosage of 0.3 g.l-1 to 0.5 g.l-1. The kinetics of interactions
were tested with pseudo first order Lagergran equation and the value
for k1 was found to be 6.909 x 10-3 min-1. The biosorption data gave
a good fit with Langmuir and Fruendlich isotherms and the Langmuir
monolayer capacity (qm) was found to be 166.78 mg. g-1. Similarly
the Freundlich adsorption capacity (Kf) was estimated as 2.49 l g-1.
The mean values of the thermodynamic parameters ΔH, ΔS, and ΔG
were -62.42 KJ. mol-1, -0.219 KJ.mol-1 K-1 and -1.747 KJ.mol-1 at
293 K from a solution containing 0.4 g l-1 of Cu(II) showing the
biosorption to be thermodynamically favourable. These results show
good potentiality of using teak leaves as a biosorbent for the removal
of Cu(II) from aqueous solutions.
Abstract: The authors present an optimization algorithm for order reduction and its application for the determination of the relative mapping errors of linear time invariant dynamic systems by the simplified models. These relative mapping errors are expressed by means of the relative integral square error criterion, which are determined for both unit step and impulse inputs. The reduction algorithm is based on minimization of the integral square error by particle swarm optimization technique pertaining to a unit step input. The algorithm is simple and computer oriented. It is shown that the algorithm has several advantages, e.g. the reduced order models retain the steady-state value and stability of the original system. Two numerical examples are solved to illustrate the superiority of the algorithm over some existing methods.
Abstract: In this article, a single application is suggested to determine the position of vehicles using Geographical Information Systems (GIS) and Geographical Position Systems (GPS). The part of the article material included mapping three dimensional coordinates to two dimensional coordinates using UTM or LAMBERT geographical methods, and the algorithm of conversion of GPS information into GIS maps is studied. Also, suggestions are given in order to implement this system based on web (called web based systems). To apply this system in IRAN, related official in this case are introduced and their duties are explained. Finally, economy analyzed is assisted according to IRAN communicational system.