Abstract: F-actin fibrils are the cytoskeleton of osteocytes. They react in a dynamic manner to mechanical loading, and strength and
reposition their efforts to reinforce the cells structure. We hypothesize that f-actin is temporarly disrupted after loading and repolymerizes
in a new orientation to oppose the applied load. In vitro studies are conducted to determine f-actin disruption after varying mechanical stimulus parameters that are known to affect bone
formation. Results indicate that the f-actin cytoskeleton is disrupted in vitro as a function of applied mechanical stimulus parameters and
that the f-actin bundles reassemble after loading induced disruption
within 3 minutes after cessation of loading. The disruption of the factin
cytoskeleton depends on the magnitude of stretch, the numbers
of loading cycles, frequency, the insertion of rest between loading
cycles and extracellular calcium. In vivo studies also demonstrate
disruption of the f-actin cytoskeleton in cells embedded in the bone
matrix immediately after mechanical loading. These studies suggest
that adaptation of the f-actin fiber bundles of the cytoskeleton in
response to applied loads occurs by disruption and subsequent repolymerization.
Abstract: A self-evolution algorithm for optimizing neural networks using a combination of PSO and JPSO is proposed. The algorithm optimizes both the network topology and parameters simultaneously with the aim of achieving desired accuracy with less complicated networks. The performance of the proposed approach is compared with conventional back-propagation networks using several synthetic functions, with better results in the case of the former. The proposed algorithm is also implemented on slope stability problem to estimate the critical factor of safety. Based on the results obtained, the proposed self evolving network produced a better estimate of critical safety factor in comparison to conventional BPN network.
Abstract: Teachers form the backbone of any educational system, hence selecting qualified candidates is very crucial. In Malaysia, the decision making in the selection process involves a few stages: Initial filtering through academic achievement, taking entry examination and going through an interview session. The last stage is the most challenging since it highly depends on human judgment. Therefore, this study sought to identify the selection criteria for teacher candidates that form the basis for an efficient multi-criteria teacher-candidate selection model for that last stage. The relevant criteria were determined from the literature and also based on expert input that is those who were involved in interviewing teacher candidates from a public university offering the formal training program. There are three main competency criteria that were identified which are content of knowledge, communication skills and personality. Further, each main criterion was divided into a few subcriteria. The Analytical Hierarchy Process (AHP) technique was employed to allocate weights for the criteria and later, integrated a Simple Weighted Average (SWA) scoring approach to develop the selection model. Subsequently, a web-based Decision Support System was developed to assist in the process of selecting the qualified teacher candidates. The Teacher-Candidate Selection (TeCaS) system is able to assist the panel of interviewers during the selection process which involves a large amount of complex qualitative judgments.
Abstract: Young people have a high prevalence of mental health
problems, yet tend not to seek help. Trusted adults in young people-s
lives, such as teachers and sports coaches, can make a major positive
contribution to the mental health of young people. Teachers and
sports coaches may be in a position to be effective in supporting
young people-s mental health through promotion, prevention and
early intervention. This study reports findings from interviews with
21 teachers and 13 sports coaches of young people aged 12 to 18 in
Canberra, Australia, regarding their perceptions of the relevance and
effectiveness of their role in supporting young people-s mental
health. Both teachers and coaches perceived having influential but
slightly different roles to play in supporting mental health. There may
be potential to elevate the influence of teachers and coaches as
sources of support for young people and their mental health care.
Abstract: In nature, electromagnetic fields always appear like
atmosphere static electric field, the earth's static magnetic field and
the wide-rang frequency electromagnetic field caused by lightening.
However, besides natural electromagnetic fields (EMF), today human
beings are mostly exposed to artificial electromagnetic fields due to
technology progress and outspread use of electrical devices. To
evaluate nuisance of EMF, it is necessary to know field intensity for
every frequency which appears and compare it with allowed values.
Low frequency EMF-s around transmission and distribution lines are
time-varying quasi-static electromagnetic fields which have
conservative component of low frequency electrical field caused by
charges and eddy component of low frequency magnetic field caused
by currents. Displacement current or field delay are negligible, so
energy flow in quasi-static EMF involves diffusion, analog like heat
transfer. Electrical and magnetic field can be analyzed separately.
This paper analysis the numerical calculations in ELF-400 software
of EMF in distribution substation in shopping center. Analyzing the
results it is possible to specify locations exposed to the fields and
give useful suggestion to eliminate electromagnetic effect or reduce it
on acceptable level within the non-ionizing radiation norms and
norms of protection from EMF.
Abstract: This paper deals with a novel approach of power
transformers diagnostics. This approach identifies the exact location
and the range of a fault in the transformer and helps to reduce
operation costs related to handling of the faulty transformer, its
disassembly and repair. The advantage of the approach is a
possibility to simulate healthy transformer and also all faults, which
can occur in transformer during its operation without its
disassembling, which is very expensive in practice. The approach is
based on creating frequency dependent impedance of the transformer
by sweep frequency response analysis measurements and by 3D FE
parametrical modeling of the fault in the transformer. The parameters
of the 3D FE model are the position and the range of the axial short
circuit. Then, by comparing the frequency dependent impedances of
the parametrical models with the measured ones, the location and the
range of the fault is identified. The approach was tested on a real
transformer and showed high coincidence between the real fault and
the simulated one.
Abstract: In this paper, a two factor scheme is proposed to
generate cryptographic keys directly from biometric data, which
unlike passwords, are strongly bound to the user. Hash value of the
reference iris code is used as a cryptographic key and its length
depends only on the hash function, being independent of any other
parameter. The entropy of such keys is 94 bits, which is much higher
than any other comparable system. The most important and distinct
feature of this scheme is that it regenerates the reference iris code by
providing a genuine iris sample and the correct user password. Since
iris codes obtained from two images of the same eye are not exactly
the same, error correcting codes (Hadamard code and Reed-Solomon
code) are used to deal with the variability. The scheme proposed here
can be used to provide keys for a cryptographic system and/or for
user authentication. The performance of this system is evaluated on
two publicly available databases for iris biometrics namely CBS and
ICE databases. The operating point of the system (values of False
Acceptance Rate (FAR) and False Rejection Rate (FRR)) can be set
by properly selecting the error correction capacity (ts) of the Reed-
Solomon codes, e.g., on the ICE database, at ts = 15, FAR is 0.096%
and FRR is 0.76%.
Abstract: Video watermarking is usually considered as watermarking of a set of still images. In frame-by-frame watermarking approach, each video frame is seen as a single watermarked image, so collusion attack is more critical in video watermarking. If the same or redundant watermark is used for embedding in every frame of video, the watermark can be estimated and then removed by watermark estimate remodolulation (WER) attack. Also if uncorrelated watermarks are used for every frame, these watermarks can be washed out with frame temporal filtering (FTF). Switching watermark system or so-called SS-N system has better performance against WER and FTF attacks. In this system, for each frame, the watermark is randomly picked up from a finite pool of watermark patterns. At first SS-N system will be surveyed and then a new collusion attack for SS-N system will be proposed using a new algorithm for separating video frame based on watermark pattern. So N sets will be built in which every set contains frames carrying the same watermark. After that, using WER attack in every set, N different watermark patterns will be estimated and removed later.
Abstract: Cheating on standardized tests has been a major
concern as it potentially minimizes measurement precision. One
major way to reduce cheating by collusion is to administer multiple
forms of a test. Even with this approach, potential collusion is still
quite large. A Latin-square treatment structure for distributing
multiple forms is proposed to further reduce the colluding potential.
An index to measure the extent of colluding potential is also
proposed. Finally, with a simple algorithm, the various Latin-squares
were explored to find the best structure to keep the colluding
potential to a minimum.
Abstract: This paper proposes a new algebraic scheme to design a PID controller for higher order linear time invariant continuous systems. Modified PSO (MPSO) based model order formulation techniques have applied to obtain the effective formulated second order system. A controller is tuned to meet the desired performance specification by using pole-zero cancellation method. Proposed PID controller is attached with both higher order system and formulated second order system. The closed loop response is observed for stabilization process and compared with general PSO based formulated second order system. The proposed method is illustrated through numerical example from literature.
Abstract: Because of architectural condition and structure application, sometimes mass source and stiffness source are not coincidence, and the structure is irregular. The structure is also might be asymmetric as an asymmetric bracing in plan which leads to unbalance distribution of stiffness or because of unbalance distribution of the mass. Both condition lead to eccentricity and torsion in the structure. The deficiency of ordinary code to evaluate the performance of steel structures against earthquake has been caused designing based on performance level or capacity spectrum be used. By using the mentioned methods it is possible to design a structure that its behavior against different earthquakes be predictive. In this article 5- story buildings with different percentage of asymmetric which is because of stiffness changes have been designed. The static and dynamic nonlinear analysis under three acceleration recording has been done. Finally performance level of the structure has been evaluated.
Abstract: This study carried out in order to investigate the
effects of salinity on carbon isotope discrimination (Δ) of shoots and
roots of four sugar beet cultivars (cv) including Madison (British
origin) and three Iranian culivars (7233-P12, 7233-P21 and 7233-P29).
Plants were grown in sand culture medium in greenhouse conditions.
Plants irrigated with saline water (tap water as control, 50 mM, 150
mM, 250 mM and 350 mM of NaCl + CaCl2 in 5 to 1 molar ratio)
from 4 leaves stage for 16 weeks. Carbon isotope discrimination
significantly decreased with increasing salinity. Significant
differences of Δ between shoot and root were observed in all cvs and
all levels of salinity. Madison cv showed lower Δ in shoot and root
than other three cvs at all levels of salinity expect control, but cv
7233-P29 had significantly higher Δ values at saline conditions of 150
mM and above. Therefore, Δ might be applicable, as a useful tool, for
study of salinity tolerance of sugar beet genotypes.
Abstract: In this paper, we consider the design of pulse shaping
filter using orthogonal Hermite-Rodriguez basis functions. The pulse
shaping filter design problem has been formulated and solved as a
quadratic programming problem with linear inequality constraints.
Compared with the existing approaches reported in the literature, the
use of Hermite-Rodriguez functions offers an effective alternative to
solve the constrained filter synthesis problem. This is demonstrated
through a numerical example which is concerned with the design of
an equalization filter for a digital transmission channel.
Abstract: Nowadays wireless technology plays an important
role in public and personal communication. However, the growth of
wireless networking has confused the traditional boundaries between
trusted and untrusted networks. Wireless networks are subject to a
variety of threats and attacks at present. An attacker has the ability to
listen to all network traffic which becoming a potential intrusion.
Intrusion of any kind may lead to a chaotic condition. In addition,
improperly configured access points also contribute the risk to
wireless network. To overcome this issue, a security solution that
includes an intrusion detection and prevention system need to be
implemented. In this paper, first the security drawbacks of wireless
network will be analyzed then investigate the characteristics and also
the limitations on current wireless intrusion detection and prevention
system. Finally, the requirement of next wireless intrusion prevention
system will be identified including some key issues which should be
focused on in the future to overcomes those limitations.
Abstract: The optimal bisection width of r-dimensional N×
· · ·× N grid is known to be Nr-1 when N is even, but when
N is odd, only approximate values are available. This paper
shows that the exact bisection width of grid is Nr
-1
N-1 when N is odd.
Abstract: Impinging jets are used in various industrial areas as a cooling and drying technique. The current research is concerned with the means of improving the heat transfer for configurations with a minimum distance of the nozzle to the impingement surface. The impingement heat transfer is described using numerical methods over a wide range of parameters for an array of planar jets. These parameters include varying jet flow speed, width of nozzle, distance of nozzle, angle of the jet flow, velocity and geometry of the impingement surface. Normal pressure and shear stress are computed as additional parameters. Using dimensionless characteristic numbers the parameters and the results are correlated to gain generalized equations. The results demonstrate the effect of the investigated parameters on the flow.
Abstract: Automatic reading of handwritten cheque is a computationally
complex process and it plays an important role in financial
risk management. Machine vision and learning provide a viable
solution to this problem. Research effort has mostly been focused
on recognizing diverse pitches of cheques and demand drafts with an
identical outline. However most of these methods employ templatematching
to localize the pitches and such schemes could potentially
fail when applied to different types of outline maintained by the
bank. In this paper, the so-called outline problem is resolved by
a cheque information tree (CIT), which generalizes the localizing
method to extract active-region-of-entities. In addition, the weight
based density plot (WBDP) is performed to isolate text entities and
read complete pitches. Recognition is based on texture features using
neural classifiers. Legal amount is subsequently recognized by both
texture and perceptual features. A post-processing phase is invoked
to detect the incorrect readings by Type-2 grammar using the Turing
machine. The performance of the proposed system was evaluated
using cheque and demand drafts of 22 different banks. The test data
consists of a collection of 1540 leafs obtained from 10 different
account holders from each bank. Results show that this approach
can easily be deployed without significant design amendments.
Abstract: Thermal load calculations have been performed for
multi-layered walls that are composed of three different parts; a
common (sand and cement) plaster, and two types of locally
produced soft and hard bricks. The masonry construction of these
layered walls was based on concrete-backed stone masonry made of
limestone bricks joined by mortar. These multilayered walls are
forming the outer walls of the building envelope of a typical Libyan
house. Based on the periodic seasonal weather conditions, within the
Libyan cost region during summer and winter, measured thermal
conductivity values were used to implement such seasonal variation
of heat flow and the temperature variations through the walls. The
experimental measured thermal conductivity values were obtained
using the Hot Disk technique. The estimation of the thermal
resistance of the wall layers ( R-values) is based on measurements
and calculations. The numerical calculations were done using a
simplified analytical model that considers two different wall
constructions which are characteristics of such houses. According to
the obtained results, the R-values were quite low and therefore,
several suggestions have been proposed to improve the thermal
loading performance that will lead to a reasonable human comfort
and reduce energy consumption.
Abstract: Analytical seismic response of multi-story building
supported on base isolation system is investigated under real
earthquake motion. The superstructure is idealized as a shear type
flexible building with lateral degree-of-freedom at each floor. The
force-deformation behaviour of the isolation system is modelled by
the bi-linear behaviour which can be effectively used to model all
isolation systems in practice. The governing equations of motion of
the isolated structural system are derived. The response of the system
is obtained numerically by step-by-method under three real recorded
earthquake motions and pulse motions associated in the near-fault
earthquake motion. The variation of the top floor acceleration, interstory
drift, base shear and bearing displacement of the isolated
building is studied under different initial stiffness of the bi-linear
isolation system. It was observed that the high initial stiffness of the
isolation system excites higher modes in base-isolated structure and
generate floor accelerations and story drift. Such behaviour of the
base-isolated building especially supported on sliding type of
isolation systems can be detrimental to sensitive equipment installed
in the building. On the other hand, the bearing displacement and base
shear found to reduce marginally with the increase of the initial
stiffness of the initial stiffness of the isolation system. Further, the
above behaviour of the base-isolated building was observed for
different parameters of the bearing (i.e. post-yield stiffness and
characteristic strength) and earthquake motions (i.e. real time history
as well as pulse type motion).
Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.