Abstract: Two constructions of unit-memory binary convolutional
codes from linear block codes over the finite semi-local ring F2r +vF2r , where v2 = v, are presented. In both cases, if the linear block code is systematic, then the resulting convolutional encoder
is systematic, minimal, basic and non-catastrophic. The Hamming
free distance of the convolutional code is bounded below by the
minimum Hamming distance of the block code. New examples of
binary convolutional codes that meet the Heller upper bound for
systematic codes are given.
Abstract: The objective of the present paper is a numerical
analysis of the flow forces acting on spool surfaces of a pressure
regulated valve. The transient, compressible and turbulent flow
structures inside the valve are simulated using ANSYS FLUENT
coupled with a special UDF. Here, valve inlet pressure is varied in a
stepwise manner. For every value of inlet pressure, transient analysis
leads to a quasi-static flow through the valve. Spool forces are
calculated based on different pressures at inlet. From this information
of spool forces, pressure characteristic of the passive control circuit
has been derived.
Abstract: This paper will provide the kinematic and dynamic
analysis of a lower limb exoskeleton. The forward and inverse
kinematics of proposed exoskeleton is performed using Denevit and
Hartenberg method. The torques required for the actuators will be
calculated using Lagrangian formulation technique. This research can
be used to design the control of the proposed exoskeleton.
Abstract: In this paper, a residue number arithmetic is used in
direct sequence spread spectrum system, this system is evaluated and
the bit error probability of this system is compared to that of non
residue number system. The effect of channel bandwidth, PN
sequences, multipath effect and modulation scheme are studied. A
Matlab program is developed to measure the signal-to-noise ratio
(SNR), and the bit error probability for the various schemes.
Abstract: Reduction of Single Input Single Output (SISO) continuous systems into Reduced Order Model (ROM), using a conventional and an evolutionary technique is presented in this paper. In the conventional technique, the mixed advantages of Mihailov stability criterion and continued fraction expansions (CFE) technique is employed where the reduced denominator polynomial is derived using Mihailov stability criterion and the numerator is obtained by matching the quotients of the Cauer second form of Continued fraction expansions. In the evolutionary technique method Particle Swarm Optimization (PSO) is employed to reduce the higher order model. PSO method is based on the minimization of the Integral Squared Error (ISE) between the transient responses of original higher order model and the reduced order model pertaining to a unit step input. Both the methods are illustrated through numerical example.
Abstract: Fractional Fourier Transform is a powerful tool,
which is a generalization of the classical Fourier Transform. This
paper provides a mathematical relation relating the span in Fractional
Fourier domain with the amplitude and phase functions of the signal,
which is further used to study the variation of quality factor with
different values of the transform order. It is seen that with the
increase in the number of transients in the signal, the deviation of
average Fractional Fourier span from the frequency bandwidth
increases. Also, with the increase in the transient nature of the signal,
the optimum value of transform order can be estimated based on the
quality factor variation, and this value is found to be very close to
that for which one can obtain the most compact representation. With
the entire mathematical analysis and experimentation, we consolidate
the fact that Fractional Fourier Transform gives more optimal
representations for a number of transform orders than Fourier
transform.
Abstract: Groundwater is one of the most important water resources in Fars province. Based on this study, 95 percent of the total annual water consumption in Fars is used for agriculture, whereas the percentages for domestic and industrial uses are 4 and 1 percent, respectively. Population growth, urban and industrial growth, and agricultural development in Fars have created a condition of water stress. In this province, farmers and other users are pumping groundwater faster than its natural replenishment rate, causing a continuous drop in groundwater tables and depletion of this resource. In this research variation of groundwater level , their effects and ways to help control groundwater levels in some plains of Fars were evaluated .Excessive exploitation of groundwater in Darab, Jahrom, Estahban, Arsanjan, Khir and Niriz plains of Fars caused the groundwater levels fall too fast or to unacceptable levels. The average drawdown of the water table in Arsanjan, Khir. Estahban and Niriz plain plains were 12,8, 9 and 6 meters during 16,11,11 and 13 years ago respectively. This not only reduces available water resources and well yields but also can saline water intrusion, reductions in river flow and in wetland areas , drying springs, and ground subsidence, considerable increase in pumping costs and a significant decline in crop yields as a result of the increasing salinity. Finally based on situation and condition of the aquifer some suggestions are recommended.
Abstract: The paper deals with determination of electromagnetic
and temperature field distribution of induction heating system used
for pipe brazing. The problem is considered as coupled – time
harmonic electromagnetic and transient thermal field. It has been
solved using finite element method. The detailed maps of
electromagnetic and thermal field distribution have been obtained.
The good understanding of the processes in the considered system
ensures possibilities for control, management and increasing the
efficiency of the welding process.
Abstract: While service quality is acceptably most valued in the tourism industry, the issue of safety and security plays a key role in sustaining the industry success. Such an issue has been part of Thailand-s tourism development and promotion for several years. Evidently, the Tourist Police Department was set up for this purpose. Its main responsibility is to deal with international tourists- safety and confidence in travelling within Thai territory. However, to strengthen the tourism safety of the country, it is important to better understand international tourists- safety concerns about Thailand. This article seeks to compare international tourists- safety needs and Thai tourist polices- perception towards the tourists- safety concern to determine what measure should be taken to assure the tourist of Thailand-s secure environment. Through the employment of quantitative and qualitative methodological approaches, the tourism safety need of international tourists from Europe, North America and Asia was excavated, how Thai tourist polices and local polices perceived the international tourist-s safety concern was investigated, and opinion and experiences about how the police deal with international tourists- problems in eight touristic areas were also explored. A comparative result reveals a certain degrees of differences in international tourists- safety needs and Thai polices- perception towards their needs. The tourism safety prevention and protection measure and practice are also suggested.
Abstract: Hardness of the widely used structural steel is of vital
importance since it may help in the determination of many
mechanical properties of a material under loading situations. In order
to obtain reliable information for design, properties homogeneity
should be validated. In the current study the hardness variation over
the different diameters of the same AISI 4140 bar is investigated.
Measurements were taken on the two faces of the stock at equally
spaced eight sectors and fifteen layers. Statistical and graphical
analysis are performed to asses the distribution of hardness
measurements over the specified area. Hardness measurements
showed some degree of dispersion with about ± 10% of its nominal
value provided by manufacturer. Hardness value is found to have a
slight decrease trend as the diameter is reduced. However, an
opposite behavior is noticed regarding the sequence of the sector
indicating a nonuniform distribution over the same area either on the
same face or considering the corresponding sector on the other face
(cross section) of the same material bar.
Abstract: Censored Production Rule is an extension of standard
production rule, which is concerned with problems of reasoning with
incomplete information, subject to resource constraints and problem
of reasoning efficiently with exceptions. A CPR has a form: IF A
(Condition) THEN B (Action) UNLESS C (Censor), Where C is the
exception condition. Fuzzy CPR are obtained by augmenting
ordinary fuzzy production rule “If X is A then Y is B with an
exception condition and are written in the form “If X is A then Y is B
Unless Z is C. Such rules are employed in situation in which the
fuzzy conditional statement “If X is A then Y is B" holds frequently
and the exception condition “Z is C" holds rarely. Thus “If X is A
then Y is B" part of the fuzzy CPR express important information
while the unless part acts only as a switch that changes the polarity of
“Y is B" to “Y is not B" when the assertion “Z is C" holds. The
proposed approach is an attempt to discover fuzzy censored
production rules from set of discovered fuzzy if then rules in the
form:
A(X)  B(Y) || C(Z).
Abstract: The aim of this study was to compare the effects
of an altitude training camp on heart rate variability and
performance in elite triathletes. Ten athletes completed 20 days of live-high, train-low training at 1650m. Athletes
underwent pre and post 800-m swim time trials at sea-level, and two heart rate variability tests at 1650m on the first and
last day of the training camp. Based on their time trial results,
athletes were divided into responders and non-responders. Relative to the non-responders, the responders sympathetic-toparasympathetic
ratio decreased substantially after 20 days of altitude training (-0.68 ± 1.08 and -1.2 ± 0.96, mean ± 90%
confidence interval for supine and standing respectively). In
addition, sympathetic activity while standing was also
substantially lower post-altitude in the responders compared to the non-responders (-1869 ± 4764 ms2). Results indicate that
responders demonstrated a change to more vagal
predominance compared to non-responders.
Abstract: Battery storage system is emerging as an essential component of hybrid power system based on renewable energy resources such as solar and wind in order to make these sources dispatchable. Accurate modeling of battery storage system is ssential in order to ensure optimal planning of hybrid power systems incorporating battery storage. Majority of the system planning studies involving battery storage assume battery charging efficiency to be constant. However a strong correlation exists between battery charging efficiency and battery state of charge. In this work a Fuzzy logic based model has been presented for determining battery charging efficiency relative to a particular SOC. In order to demonstrate the efficacy of proposed approach, reliability evaluation studies are carried out for a hypothetical autonomous hybrid power system located in Jaisalmer, Rajasthan, India. The impact of considering battery charging efficiency as a function of state of charge is compared against the assumption of fixed battery charging efficiency for three different configurations comprising of wind-storage, solar-storage and wind-solar-storage.
Abstract: The evaluation of unit cell neutronic parameters and
lifetime for some innovant reactors without on sit-refuling will be
held in this work. the behavior of some small and medium reactors
without on site refueling with triso and cermet fuel. For the FBNR
long life except we propose to change the enrichment of the Cermet
MFE to 9%. For the AFPR reactor we can see that the use of the
Cermet MFE can extend the life of this reactor but to maintain the
same life period for AFPR-SC we most use burnup poison to have the
same slope for Kinf (Burnup). PFPWR50 cell behaves almost in
same way using both fuels Cermet and TRISO. So we can conclude
that PFPWR50 reactor, with CERMET Fuel, is kept among the long
cycle reactors and with the new configuration we avoid subcriticality
at the beginning of cycle. The evaluation of unit cell neutronic
parameters reveals a good agreement with the goal of BWR-PB
concept. It is found out that the Triso fuel assembly lifetime can be
extended for a reasonably long period without being refueled,
approximately up to 48GWd/t burnup. Using coated particles fuels
with the Cermet composition can be more extended the fuel assembly
life time, approximately 52 GWd/t.
Abstract: The application of stability theory has led to detailed studies of different types of vessels; however, the shortage of information relating to multihull vessels demanded further investigation. This study shows that the position of the hulls has a very influential effect on both the transverse and longitudinal stability of the tricore. HSC stability code is applied for the optimisation of the hull configurations. Such optimization criteria would undoubtedly aid the performance of the vessel for both commercial or leisure purposes
Abstract: Heavy rainfall greatly affects the aerodynamic performance of the aircraft. There are many accidents of aircraft caused by aerodynamic efficiency degradation by heavy rain. In this Paper we have studied the heavy rain effects on the aerodynamic efficiency of NACA 64-210 & NACA 0012 airfoils. For our analysis, CFD method and preprocessing grid generator are used as our main analytical tools, and the simulation of rain is accomplished via two phase flow approach-s Discrete Phase Model (DPM). Raindrops are assumed to be non-interacting, non-deforming, non-evaporating and non-spinning spheres. Both airfoil sections exhibited significant reduction in lift and increase in drag for a given lift condition in simulated rain. The most significant difference between these two airfoils was the sensitivity of the NACA 64-210 to liquid water content (LWC), while NACA 0012 performance losses in the rain environment is not a function of LWC . It is expected that the quantitative information gained in this paper will be useful to the operational airline industry and greater effort such as small scale and full scale flight tests should put in this direction to further improve aviation safety.
Abstract: Mobile Picture Puzzle is a mobile game application where the player use existing images stored in the mobile phone to create a puzzle to be played. This traditional picture puzzle is not so challenging once the player is familiar with the game. The objective of the developed mobile game application is to have a similar mobile game application that can provide the player with more challenging gaming experience. The developed mobile game application is also a mobile picture puzzle game application to create a puzzle to be played but instead of just using existing images that are stored, the personalised capability allows the player to use the built-in camera phone to capture an image and use the newly captured image to create the puzzle. The development of the mobile game application uses Symbian Operating System (OS), Mobile Media API (Application Programming Interface), Record Management System (RMS) storage and TiledLayer class from Game API.
Abstract: Many digital signal processing, techniques have been used to automatically distinguish protein coding regions (exons) from non-coding regions (introns) in DNA sequences. In this work, we have characterized these sequences according to their nonlinear dynamical features such as moment invariants, correlation dimension, and largest Lyapunov exponent estimates. We have applied our model to a number of real sequences encoded into a time series using EIIP sequence indicators. In order to discriminate between coding and non coding DNA regions, the phase space trajectory was first reconstructed for coding and non-coding regions. Nonlinear dynamical features are extracted from those regions and used to investigate a difference between them. Our results indicate that the nonlinear dynamical characteristics have yielded significant differences between coding (CR) and non-coding regions (NCR) in DNA sequences. Finally, the classifier is tested on real genes where coding and non-coding regions are well known.
Abstract: Saturated two-phase fluid flows are often subject to
pressure induced oscillations. Due to compressibility the vapor
bubbles act as a spring with an asymmetric non-linear characteristic.
The volume of the vapor bubbles increases or decreases differently if
the pressure fluctuations are compressing or expanding;
consequently, compressing pressure fluctuations in a two-phase pipe
flow cause less displacement in the direction of the pipe flow than
expanding pressure fluctuations. The displacement depends on the
ratio of liquid to vapor, the ratio of pressure fluctuations over average
pressure and on the exciting frequency of the pressure fluctuations.
In addition, pressure fluctuations in saturated vapor bubbles cause
condensation and evaporation within the bubbles and change
periodically the ratio between liquid to vapor, and influence the
dynamical parameters for the oscillation. The oscillations are
conforming to an isenthalpic process at constant enthalpy with no
heat transfer and no exchange of work.
The paper describes the governing non-linear equation for twophase
fluid oscillations with condensation and evaporation, and
presents steady state approximate solutions for free and for pressure
induced oscillations. Resonance criteria and stability are discussed.
Abstract: Project selection problems on management
information system (MIS) are often considered a multi-criteria
decision-making (MCDM) for a solving method. These problems
contain two aspects, such as interdependencies among criteria and
candidate projects and qualitative and quantitative factors of projects.
However, most existing methods reported in literature consider these
aspects separately even though these two aspects are simultaneously
incorporated. For this reason, we proposed a hybrid method using
analytic network process (ANP) and fuzzy logic in order to represent
both aspects. We then propose a goal programming model to conduct
an optimization for the project selection problems interpreted by a
hybrid concept. Finally, a numerical example is conducted as
verification purposes.