Abstract: High Resolution NMR Spectroscopy offers unique screening capabilities for food quality and safety by combining non-targeted and targeted screening in one analysis.
The objective is to demonstrate, that due to its extreme reproducibility NMR can detect smallest changes in concentrations of many components in a mixture, which is best monitored by statistical evaluation however also delivers reliable quantification results.
The methodology typically uses a 400 MHz high resolution instrument under full automation after minimized sample preparation.
For example one fruit juice analysis in a push button operation takes at maximum 15 minutes and delivers a multitude of results, which are automatically summarized in a PDF report.
The method has been proven on fruit juices, where so far unknown frauds could be detected. In addition conventional targeted parameters are obtained in the same analysis. This technology has the advantage that NMR is completely quantitative and concentration calibration only has to be done once for all compounds. Since NMR is so reproducible, it is also transferable between different instruments (with same field strength) and laboratories. Based on strict SOP`s, statistical models developed once can be used on multiple instruments and strategies for compound identification and quantification are applicable as well across labs.
Abstract: Venison is well known as a traditional meat type in Europe and it is lower in calories, cholesterol and fat content than common cuts of beef, pork or lamb. The aim of the current research was to determine content of amino acids (LVS ISO 13903:2005) in different types of marinades marinated venison during storage. Beef as a control was analyzed for comparison of obtained results. The meat (2x3x2cm) pieces were marinated in two different types of marinades: red wine and tomato sauce marinade. The prepared meat samples were stored (marinated) at 4±2ºC temperature for 48±1h. Marinated meat was placed in polypropylene trays, hermetically sealed with high barrier polymer film under modified atmosphere (C02 40%+N2 60%) without and with iron based oxygen scavenger sachets (Mitsubishi Gas Chemical Europe Ageless®), all samples were compared with packed marinated products in air ambiance. Results of current research show that changes of amino acids content in marinated venison mainly depend on packaging conditions.
Abstract: Triticale is a manmade hybrid of wheat and rye that carries the A and B genome of durum wheat and the R genome of rye. In the scientific literature information about in Latvia harvested organic and conventional triticale grain physically-chemical composition was not found in general. Therefore, the main purpose of the current research was to investigate physically-chemical parameters of in Latvia harvested organic and convectional triticale grains. The research was accomplished on in Year 2012 from State Priekuli Plant Breeding Institute (Latvia) harvested organic and conventional triticale grains: “Dinaro”, “9403-97”, “9405-23” and “9402-3”. In the present research significant differences in chemical composition between organic and conventional triticale grains harvested in Latvia was found. It is necessary to mention that higher 1000 grain weight, bulk density and gluten index was obtained for conventional and organic triticale grain variety “9403-97”. However higher falling number, gluten and protein content was obtained for triticale grain variety “9405-23”.
Abstract: The objective of the present study was to determine quality parameters changes of red wine marinade marinated venison during storage. Beef as a control was analysed. Protein, fat, moisture and pH content dynamics as well microbiological quality was analyzed. The meat pieces were marinated in red wine marinade at 4±2ºC temperature for 48±1h. Marinated meat was placed in polypropylene trays, hermetically sealed with high barrier polymer film Multibarrier 60 under modified atmosphere (CO2 40%+N2 60%) without and with oxygen absorber sachets, as a control packaging in air ambiance packed marinated venison and beef was used. Meat samples were analyzed after 0, 4, 7, 11 and 14 days of storage. During the storage of meat, protein and moisture content significantly (p
Abstract: Haemodialysis (HD) is a procedure saving patient lives around the world, unfortunately it brings numerous complications. Oxidative stress is one of the major factors which lead to erythrocytes destruction during extracorporeal circulation. Repeated HD procedures destroy blood elements and the organism is not able to keep up with their production. 30 HD procedures on healthy sheep were performed to evaluate effects of such treatment. Oxidative stress study was performed together with an analysis of basic blood parameters and empirical assessment of dialyzer condition after the procedure. A reversible decline in absolute leukocyte count, during first 30 min of HD, was observed. Blood clots were formed in the area of the blood inlet and outlet of the dialyzer. Our results are consistent with outcomes presented throughout the literature specifically with respect to the effects observed in humans and will provide a basis to evaluate methods for blood protection during haemodialysis.
Abstract: The purpose of the study is to analyze the main tourism attraction in indigenous tribes, as well as for the development of tribal aboriginal tourism brings positive and negative impacts. This study used qualitative research methods, and Lilang, Tbulan, and Hrung three tribes as the object of investigation. The results showed that: 1. Because three tribes geographical proximity, but have their own development characteristics, not conflict situations. 2. Three tribes are located in National Scenic Area and National Forest Recreation Area near, so driven tribal tourism development. 3 In addition Hrung three tribal tribal no major attraction, mainly located in the provision of accommodation; another Lilang and Tbulan tribe has natural resources and cultural resources attraction. 4 in the tourism brings positive and negative impacts, respondents expressed positive than residents of negative impacts. Based on the above findings, this study not only provides advice for tribal tourism operators, but also for future research to provide specific directions.
Abstract: The tribological outcomes of micro dent are found to be outstanding in many engineering and natural surfaces. Ceramic (Al2O3) is considered one of the most potential material to bearing surfaces particularly, artificial hip or knee implant. A well-defined micro dent on alumina oxide interface could further decrease friction and wear rate, thus increase their stability and durability. In this study we fabricated circular micro dent surface profiles (Dia: 400µm, Depth 20µm, P: 1.5mm; Dia: 400µm, Depth 20µm, P: 2mm) on pure Al2O3 (99.6%) substrate by using a micro tool machines. A preliminary tribological experiment was carried out to compare friction coefficient of these fabricated dent surfaces with that of non-textured surfaces. The experiment was carried on well know pin-on-disk specimens while other experimental parameters such as hertz pressure, speed, lubrication, and temperature were maintained to standard of simulated hip joints condition. The experiment results revealed that micro dent surface texture reduced 15%, 8% and 4% friction coefficient under 0.132,0.162, 0.187 GPa contact pressure respectively. Since this is a preliminary tribological study, we will pursue further experiments considering higher ranges of dent profiles and longer run experiments. However, the preliminary results confirmed the suitability of fabricating dent profile to ceramic surfaces by using micro tooling, and also their improved tribological performance in simulated hip joints.
Abstract: The influence of copper and zinc supplements on milk
production performances and health indicators was tested in a 20-
week feeding trial, with 40 Holstein-Friesian lactating cows, devided
in four groups (copper, zinc, copper-zinc and control). Correlations of
the Cu and Zn plasma values with some animal performance criteria
of health (body condition score and somatic cell counts) and
production (milk yield, peak milk yield, fat and crude protein
content) were done. During the 140 days of the experiment, the two
added minerals caused a statistically significant increase (p < 0.05) of
their plasma values after the peak of the cows’ lactations. It was also
observed that subjects that have received copper and zinc
supplements had the lowest number of somatic cell counts in milk.
The Pearson correlation test showed a positive corellation (p = 0.007,
r = + 0.851) between the plasma Zn and the milk production. The
improvement of the nutritional status improved the milk production
performances of the cows as well as their health performances.
Abstract: Provision of optical devices without proper instruction
and training may cause frustration resulting in rejection or incorrect
use of the magnifiers. However training in the use of magnifiers
increases the cost of providing these devices. This study compared
the efficacy of providing instruction alone and instruction plus
training in the use of magnifiers. 24 participants randomly assigned
to two groups. 15 received instruction and training and 9 received
instruction only. Repeated measures of print size and reading speed
were performed at pre, post training and follow up. Print size
decreased in both groups between pre and post training maintained at
follow up. Reading speed increased in both groups over time with the
training group demonstrating more rapid improvement. Whilst
overall outcomes were similar, training decreased the time required
to increase reading speed supporting the use of training for increased
efficiency. A cost effective form of training is suggested.
Abstract: The impacts of near-campus student housing, or offcampus
students accommodation cannot be ignored by the
universities and as well as the community officials. Numerous
scholarly studies, have highlighted the substantial economic impacts
either; direct, indirect or induced, and cumulatively the roles of the
universities have significantly contributed to the local economies.
The issue of the impacts of off-campus student rental housing on
neighbourhoods is one that has been of long-standing but increasing
concern in Malaysia. Statistically, in Malaysia, there was
approximately a total of 1.2 - 1.5 million students in 2009. By the
year 2015, it is expected that 50 per cent of 18 to 30 year olds active
population should gain access to university education, amounting to
120,000 yearly. The objectives of the research are to assess the
impacts off-campus students on the local neighbourhood and
specifically to obtain information on the living and learning
conditions of off-campus students of Universiti Teknologi MARA
Shah Alam, Malaysia. It is also to isolate those factors that may
impede the successful learning so that priority can be given to them
in subsequent policy implementations and actions by government and
the higher education institutions.
Abstract: The goal of this paper is to examine the effects of laser
radiation on the skin wound healing using infrared thermography as
non-invasive method for the monitoring of the skin temperature
changes during laser treatment. Thirty Wistar rats were used in this
study. A skin lesion was performed at the leg on all rats. The animals
were exposed to laser radiation (λ = 670 nm, P = 15 mW, DP = 16.31
mW/cm2) for 600 s. Thermal images of wound were acquired before
and after laser irradiation. The results have demonstrated that the
tissue temperature decreases from 35.5±0.50°C in the first treatment
day to 31.3±0.42°C after the third treatment day. This value is close
to the normal value of the skin temperature and indicates the end of
the skin repair process. In conclusion, the improvements in the
wound healing following exposure to laser radiation have been
revealed by infrared thermography.
Abstract: This study was an investigation on the suitability of Lahar/HDPE composite as a primary material for low-cost smallscale biogas digesters. While sources of raw materials for biogas are abundant in the Philippines, cost of the technology has made the widespread utilization of this resource an indefinite proposition. Aside from capital economics, another problem arises with space requirements of current digester designs. These problems may be simultaneously addressed by fabricating digesters on a smaller, household scale to reach a wider market, and to use materials that may accommodate optimization of overall design and fabrication cost without sacrificing operational efficiency. This study involved actual fabrication of the Lahar/HDPE composite at varying composition and geometry, subsequent mechanical and thermal characterization, and implementation of Statistical Analysis to find intrinsic relationships between variables. From the results, Lahar/HDPE composite was found to be feasible for use as digester material from both mechanical and economic standpoints.
Abstract: According to the increasing utilization in power system, the transmission lines and power plants often operate in stability boundary and system probably lose its stable condition by over loading or occurring disturbance. According to the reasons that are mentioned, the prediction and recognition of voltage instability in power system has particular importance and it makes the network security stronger.This paper, by considering of power system contingencies based on the effects of them on Mega Watt Margin (MWM) and maximum loading point is focused in order to analyse the static voltage stability using continuation power flow method. The study has been carried out on IEEE 14-Bus Test System using Matlab and Psat softwares and results are presented.
Abstract: Microscopic emission and fuel consumption models
have been widely recognized as an effective method to quantify real
traffic emission and energy consumption when they are applied with
microscopic traffic simulation models. This paper presents a
framework for developing the Microscopic Emission (HC, CO, NOx,
and CO2) and Fuel consumption (MEF) models for light-duty
vehicles. The variable of composite acceleration is introduced into
the MEF model with the purpose of capturing the effects of historical
accelerations interacting with current speed on emission and fuel
consumption. The MEF model is calibrated by multivariate
least-squares method for two types of light-duty vehicle using
on-board data collected in Beijing, China by a Portable Emission
Measurement System (PEMS). The instantaneous validation results
shows the MEF model performs better with lower Mean Absolute
Percentage Error (MAPE) compared to other two models. Moreover,
the aggregate validation results tells the MEF model produces
reasonable estimations compared to actual measurements with
prediction errors within 12%, 10%, 19%, and 9% for HC, CO, NOx
emissions and fuel consumption, respectively.
Abstract: An adaptive dynamic cerebellar model articulation
controller (DCMAC) neural network used for solving the prediction
and identification problem is proposed in this paper. The proposed
DCMAC has superior capability to the conventional cerebellar model
articulation controller (CMAC) neural network in efficient learning
mechanism, guaranteed system stability and dynamic response. The
recurrent network is embedded in the DCMAC by adding feedback
connections in the association memory space so that the DCMAC
captures the dynamic response, where the feedback units act as
memory elements. The dynamic gradient descent method is adopted to
adjust DCMAC parameters on-line. Moreover, the analytical method
based on a Lyapunov function is proposed to determine the
learning-rates of DCMAC so that the variable optimal learning-rates
are derived to achieve most rapid convergence of identifying error.
Finally, the adaptive DCMAC is applied in two computer simulations.
Simulation results show that accurate identifying response and
superior dynamic performance can be obtained because of the
powerful on-line learning capability of the proposed DCMAC.
Abstract: Reliable water level forecasts are particularly
important for warning against dangerous flood and inundation. The
current study aims at investigating the suitability of the adaptive
network based fuzzy inference system for continuous water level
modeling. A hybrid learning algorithm, which combines the least
square method and the back propagation algorithm, is used to
identify the parameters of the network. For this study, water levels
data are available for a hydrological year of 2002 with a sampling
interval of 1-hour. The number of antecedent water level that should
be included in the input variables is determined by two statistical
methods, i.e. autocorrelation function and partial autocorrelation
function between the variables. Forecasting was done for 1-hour until
12-hour ahead in order to compare the models generalization at
higher horizons. The results demonstrate that the adaptive networkbased
fuzzy inference system model can be applied successfully and
provide high accuracy and reliability for river water level estimation.
In general, the adaptive network-based fuzzy inference system
provides accurate and reliable water level prediction for 1-hour ahead
where the MAPE=1.15% and correlation=0.98 was achieved. Up to
12-hour ahead prediction, the model still shows relatively good
performance where the error of prediction resulted was less than
9.65%. The information gathered from the preliminary results
provide a useful guidance or reference for flood early warning
system design in which the magnitude and the timing of a potential
extreme flood are indicated.
Abstract: MM-Path, an acronym for Method/Message Path, describes the dynamic interactions between methods in object-oriented systems. This paper discusses the classifications of MM-Path, based on the characteristics of object-oriented software. We categorize it according to the generation reasons, the effect scope and the composition of MM-Path. A formalized representation of MM-Path is also proposed, which has considered the influence of state on response method sequences of messages. .Moreover, an automatic MM-Path generation approach based on UML Statechart diagram has been presented, and the difficulties in identifying and generating MM-Path can be solved. . As a result, it provides a solid foundation for further research on test cases generation based on MM-Path.
Abstract: A vertical SOI-based MOSFET with trench body
structure operated as 1T DRAM cell at various temperatures has been
studied and investigated. Different operation temperatures are
assigned for the device for its performance comparison, thus the
thermal stability is carefully evaluated for the future memory device
applications. Based on the simulation, the vertical SOI-based
MOSFET with trench body structure demonstrates the electrical
characteristics properly and possess conspicuous kink effect at
various operation temperatures. Transient characteristics were also
performed to prove that its programming window values and
retention time behaviors are acceptable when the new 1T DRAM cell
is operated at high operation temperature.
Abstract: Automotive suspension system is important part of car
comfort and safety. In this article automotive active suspension with
linear motor as actuator is designed using H-infinity control. This
paper is focused on comparison of different controller designed for
quart, half or full-car model (and always used for “full" car). Special
attention is placed on energy demand of the whole system. Each
controller configuration is simulated and then verified on the
hydraulic quarter car test bed.
Abstract: With a rapid growth in 3D graphics technology over the last few years, people are desired to see more flexible reacting motions of a biped in animations. In particular, it is impossible to anticipate all reacting motions of a biped while facing a perturbation. In this paper, we propose a three-level tracking method for animating a 3D humanoid character. First, we take the laws of physics into account to attach physical attributes, such as mass, gravity, friction, collision, contact, and torque, to bones and joints of a character. The next step is to employ PD controller to follow a reference motion as closely as possible. Once the character cannot tolerate a strong perturbation to prevent itself from falling down, we are capable of tracking a desirable falling-down action to avoid any falling condition inaccuracy. From the experimental results, we demonstrate the effectiveness and flexibility of the proposed method in comparison with conventional data-driven approaches.