Abstract: Electro-optical (EO) stabilized platforms have been widely used for surveillance and reconnaissance on various types of vehicles, from surface ships to unmanned air vehicles (UAVs). EO stabilized platforms usually consist of an assembly of structure, bearings, and motors called gimbals in which a gyroscope is installed. EO elements such as a CCD camera and IR camera, are mounted to a gimbal, which has a range of motion in elevation and azimuth and can designate and track a target. In addition, a laser range finder (LRF) can be added to the gimbal in order to acquire the precise slant range from the platform to the target. Recently, a versatile functionality of target localization is needed in order to cooperate with the weapon systems that are mounted on the same platform. The target information, such as its location or velocity, needed to be more accurate. The accuracy of the target information depends on diverse component errors and alignment errors of each component. Specially, the type of moving platform can affect the accuracy of the target information. In the case of flying platforms, or UAVs, the target location error can be increased with altitude so it is important to measure altitude as precisely as possible. In the case of surface ships, target location error can be increased with obliqueness of the elevation angle of the gimbal since the altitude of the EO stabilized platform is supposed to be relatively low. The farther the slant ranges from the surface ship to the target, the more extreme the obliqueness of the elevation angle. This can hamper the precise acquisition of the target information. So far, there have been many studies on EO stabilized platforms of flying vehicles. However, few researchers have focused on ship-borne EO stabilized platforms of the surface ship. In this paper, we deal with a target localization method when an EO stabilized platform is located on the mast of a surface ship. Especially, we need to overcome the limitation caused by the obliqueness of the elevation angle of the gimbal. We introduce a well-known approach for target localization using Unscented Kalman Filter (UKF) and present the problem definition showing the above-mentioned limitation. Finally, we want to show the effectiveness of the approach that will be demonstrated through computer simulations.
Abstract: In this paper, we analyze major components of activity recognition (AR) in wearable device with 9-axis sensors and sensor fusion filters. 9-axis sensors commonly include 3-axis accelerometer, 3-axis gyroscope and 3-axis magnetometer. We chose sensor fusion filters as Kalman filter and Direction Cosine Matrix (DCM) filter. We also construct sensor fusion data from each activity sensor data and perform classification by accuracy of AR using Naïve Bayes and SVM. According to the classification results, we observed that the DCM filter and the specific combination of the sensing axes are more effective for AR in wearable devices while classifying walking, running, ascending and descending.
Abstract: This study examined the influences of including LGBTQ-related content in a multicultural teacher education course on the development of prospective teachers’ social justice identities. Appling a content analysis to 53 reflection texts written by participating prospective teachers in response to the relevant course content, this study deduced the stages of social justice identity development (naïve, acceptance, resistance, redefinition, and internalization) that participants reached during the course. The analysis demonstrated that the participants reached various stages in the social identity development model and none of the participants remained at the naïve stage during/after class. The majority (53%) of the participants reached the internalization stage during the coursework and became conscious about the heterosexual privileges they have had and aware of possible impacts of such privilege on their future LGBTQ students. Also the participants had begun to develop pedagogic action plans and devised applicable teaching strategies for their future students based on the new understanding of heteronormativity. We expect this study will benefit teacher educators and educational administrators who want to address LGBTQ-related issues in their multicultural education programs and/or revisit the goals, directions, and implications of their approach.
Abstract: Adequate sleep affects various parts of one’s overall physical and mental life. As one of the methods in determining the appropriate amount of sleep, this research presents a heart rate based sleep quality index. In order to evaluate sleep quality using the heart rate, sleep data from 280 subjects taken over one month are used. Their sleep data are categorized by a three-part heart rate range. After categorizing, some features are extracted, and the statistical significances are verified for these features. The results show that some features of this sleep quality index model have statistical significance. Thus, this heart rate based sleep quality index may be a useful discriminator of sleep.
Abstract: As Korea government has expanded the budget for the
national research and development business, the need for the
installation of institute taking a role of deliberation, coordination, and
operation of research development business and its budget has been
increased continuously. In response to the demands of the times,
recently, the National Science & Technology Council (NSTC) was
installed. However, to achieve a creative economy more efficiently,
the fundamental introspection on the current state of the national
administration system of science and technology in Korea should be
needed. Accordingly, this study, firstly, analyzes the function and
organizational structure of NSTC in Korea. Then, this study
investigates the current state of the National Science and Technology
Council in main world countries. Lastly, this study derives some
implications based on the comparison analysis of the current state of
the National Science and Technology Council between Korea and
these countries. The present study will help in finding the way for the
advancement of the NSTC in Korea.
Abstract: Offshore floating structure under the various environmental conditions maintains a fixed position by mooring system. Environmental conditions, vessel motions and mooring loads are applied to mooring lines as the dynamic tension. Because global responses of mooring system in deep water are specified as wave frequency and low frequency response, they should be calculated from the time-domain analysis due to non-linear dynamic characteristics. To take into account all mooring loads, environmental conditions, added mass and damping terms at each time step, a lot of computation time and capacities are required. Thus, under the premise that reliable fatigue damage could be derived through reasonable analysis method, it is necessary to reduce the analysis cases through the sensitivity studies and appropriate assumptions. In this paper, effects in fatigue are studied for spread mooring system connected with oil FPSO which is positioned in deep water of West Africa offshore. The target FPSO with two Mbbls storage has 16 spread mooring lines (4 bundles x 4 lines). The various sensitivity studies are performed for environmental loads, type of responses, vessel offsets, mooring position, loading conditions and riser behavior. Each parameter applied to the sensitivity studies is investigated from the effects of fatigue damage through fatigue analysis. Based on the sensitivity studies, the following results are presented: Wave loads are more dominant in terms of fatigue than other environment conditions. Wave frequency response causes the higher fatigue damage than low frequency response. The larger vessel offset increases the mean tension and so it results in the increased fatigue damage. The external line of each bundle shows the highest fatigue damage by the governed vessel pitch motion due to swell wave conditions. Among three kinds of loading conditions, ballast condition has the highest fatigue damage due to higher tension. The riser damping occurred by riser behavior tends to reduce the fatigue damage. The various analysis results obtained from these sensitivity studies can be used for a simplified fatigue analysis of spread mooring line as the reference.
Abstract: According to the nature of the university, as a free and responsible academic community, USR is based on a different foundation —academic responsibility, so the Pyramid and the IC Model of CSR could not fully explain the most distinguished feature of USR. This paper sought to put forward a new model— Ferris Wheel Model, to illustrate the nature of USR and the process of achievement. The Ferris Wheel Model of USR shows the university creates a balanced, fairness and neutrality systemic structure to afford social responsibilities; that makes the organization could obtain a synergistic effect to achieve more extensive interests of stakeholders and wider social responsibilities.
Abstract: In this paper, we develop a dynamic modeling of wind farms in the Jeju power system. The dynamic model of wind farms is developed to study their dynamic effects on the Jeju power system. PSS/E is used to develop the dynamic model of a wind farm composed of 1.5-MW doubly fed induction generators. The output of a wind farm is regulated based on pitch angle control, in which the two controllable parameters are speed and power references. The simulation results confirm that the pitch angle is successfully controlled, regardless of the variation in wind speed and output regulation.
Abstract: The purpose of the study is to develop a finite element model based on 3D bone structural images of Micro-CT and to analyze the stress distribution for the osteoporosis mouse femora. In this study, results of finite element analysis show that the early osteoporosis of mouse model decreased a bone density in trabecular region; however, the bone density in cortical region increased.
Abstract: Reinforced concrete (RC) shear wall system of residential buildings is popular in South Korea. RC walls are subjected to axial forces in common and the effect of axial forces on the strength loss of the fire damaged walls has not been investigated. This paper aims at investigating temperature distribution on fire damaged concrete walls having different axial loads. In the experiments, a variable of specimens is axial force ratio. RC walls are fabricated with 150mm of wall thicknesses, 750mm of lengths and 1,300mm of heights having concrete strength of 24MPa. After curing, specimens are heated on one surface with ISO-834 standard time-temperature curve for 2 hours and temperature distributions during the test are measured using thermocouples inside the walls. The experimental results show that the temperature of the RC walls exposed to fire increases as axial force ratio increases. To verify the experiments, finite element (FE) models are generated for coupled temperature-structure analyses. The analytical results of thermal behaviors are in good agreement with the experimental results. The predicted displacement of the walls decreases when the axial force increases.
Abstract: Mineral product, waste concrete (fine aggregates),
waste in the optical field, industry, and construction employ separators
to separate solids and classify them according to their size. Various
sorting machines are used in the industrial field such as those operating
under electrical properties, centrifugal force, wind power, vibration,
and magnetic force. Study on separators has been carried out to
contribute to the environmental industry. In this study, we perform
CFD analysis for understanding the basic mechanism of the separation
of waste concrete (fine aggregate) particles from air with a machine
built with a rotor with blades. In CFD, we first performed
two-dimensional particle tracking for various particle sizes for the
model with 1 degree, 1.5 degree, and 2 degree angle between each
blade to verify the boundary conditions and the method of rotating
domain method to be used in 3D. Then we developed 3D numerical
model with ANSYS CFX to calculate the air flow and track the
particles. We judged the capability of particle separation for given size
by counting the number of particles escaping from the domain toward
the exit among 10 particles issued at the inlet. We confirm that
particles experience stagnant behavior near the exit of the rotating
blades where the centrifugal force acting on the particles is in balance
with the air drag force. It was also found that the minimum particle
size that can be separated by the machine with the rotor is determined
by its capability to stay at the outlet of the rotor channels.
Abstract: This study aims to establish function point process
based on stochastic distribution. In order to demonstrate effectiveness
of the study we present a case study that it applies suggested method
on an automotive electrical and electronics system software
development based on Monte Carlo Simulation. It is expected that the
result of this paper is used as guidance for establishing function point
process in organizations and tools for helping project managers make
decisions correctly.
Abstract: We present probabilistic multinomial Dirichlet
classification model for multidimensional data and Gaussian process
priors. Here, we have considered efficient computational method that
can be used to obtain the approximate posteriors for latent variables
and parameters needed to define the multiclass Gaussian process
classification model. We first investigated the process of inducing a
posterior distribution for various parameters and latent function by
using the variational Bayesian approximations and important sampling
method, and next we derived a predictive distribution of latent
function needed to classify new samples. The proposed model is
applied to classify the synthetic multivariate dataset in order to verify
the performance of our model. Experiment result shows that our model
is more accurate than the other approximation methods.
Abstract: In this paper, we propose the variational EM inference
algorithm for the multi-class Gaussian process classification model
that can be used in the field of human behavior recognition. This
algorithm can drive simultaneously both a posterior distribution of a
latent function and estimators of hyper-parameters in a Gaussian
process classification model with multiclass. Our algorithm is based
on the Laplace approximation (LA) technique and variational EM
framework. This is performed in two steps: called expectation and
maximization steps. First, in the expectation step, using the Bayesian
formula and LA technique, we derive approximately the posterior
distribution of the latent function indicating the possibility that each
observation belongs to a certain class in the Gaussian process
classification model. Second, in the maximization step, using a derived
posterior distribution of latent function, we compute the maximum
likelihood estimator for hyper-parameters of a covariance matrix
necessary to define prior distribution for latent function. These two
steps iteratively repeat until a convergence condition satisfies.
Moreover, we apply the proposed algorithm with human action
classification problem using a public database, namely, the KTH
human action data set. Experimental results reveal that the proposed
algorithm shows good performance on this data set.
Abstract: Graphene, a single-atom sheet, has been considered as
the most promising material for making future nanoelectromechanical
systems as well as purely electrical switching with graphene
transistors. Graphene-based devices have advantages in scaled-up
device fabrication due to the recent progress in large area graphene
growth and lithographic patterning of graphene nanostructures. Here
we investigated its mechanical responses of circular graphene
nanoflake under the nanoindentation using classical molecular
dynamics simulations. A correlation between the load and the
indentation depth was constructed. The nanoindented force in this
work was applied to the center point of the circular graphene nanoflake
and then, the resonance frequency could be tuned by a nanoindented
depth. We found the hardening or the softening of the graphene
nanoflake during its nanoindented-deflections, and such properties
were recognized by the shift of the resonance frequency. The
calculated mechanical parameters in the force-vs-deflection plot were
in good agreement with previous experimental and theoretical works.
This proposed schematics can detect the pressure via the deflection
change or/and the resonance frequency shift, and also have great
potential for versatile applications in nanoelectromechanical systems.
Abstract: Piezoelectric actuator is treated as RC load when it is
modeled electrically. For some piezoelectric actuator applications,
arbitrary voltage is required to actuate. Especially for unidirectional
arbitrary voltage driving like as sine wave, some special inverter with
circuit that can charge and discharge the capacitive energy can be
used. In this case, the difference between power supply level and the
object voltage level for RC load is varied. Because the control gain is
constant, the controlled output is not uniform according to the voltage
difference. In this paper, for charge and discharge circuit for
unidirectional arbitrary voltage driving for piezoelectric actuator, the
controller gain is controlled according to the voltage difference. With
the proposed simple idea, the load voltage can have controlled
smoothly although the voltage difference is varied. The
appropriateness is proved from the simulation of the proposed circuit.
Abstract: When high strength reinforced concrete is exposed to
high temperature due to a fire, deteriorations occur such as loss in
strength and elastic modulus, cracking and spalling of the concrete.
Therefore, it is important to understand risk of structural safety in
building structures by studying structural behaviors and rehabilitation
of fire damaged high strength concrete structures. This paper aims at
investigating rehabilitation effect on fire damaged high strength
concrete beams using experimental and analytical methods. In the
experiments, flexural specimens with high strength concrete are
exposed to high temperatures according to ISO 834 standard time
temperature curve. From four-point loading test, results show that
maximum loads of the rehabilitated beams are similar to or higher than
those of the non-fire damaged RC beam. In addition, structural
analyses are performed using ABAQUS 6.10-3 with same conditions
as experiments to provide accurate predictions on structural and
mechanical behaviors of rehabilitated RC beams. The parameters are
the fire cover thickness and strengths of repairing mortar. Analytical
results show good rehabilitation effects, when the results predicted
from the rehabilitated models are compared to structural behaviors of
the non-damaged RC beams. In this study, fire damaged high strength concrete beams are
rehabilitated using polymeric cement mortar. The predictions from the
finite element (FE) models show good agreements with the
experimental results and the modeling approaches can be used to
investigate applicability of various rehabilitation methods for further
study.
Abstract: In recent years, fire accidents have been steadily
increased and the amount of property damage caused by the accidents
has gradually raised. Damaging building structure, fire incidents bring
about not only such property damage but also strength degradation and
member deformation. As a result, the building structure undermines its
structural ability. Examining the degradation and the deformation is
very important because reusing the building is more economical than
reconstruction. Therefore, engineers need to investigate the strength
degradation and member deformation well, and make sure that they
apply right rehabilitation methods. This study aims at evaluating
deformation characteristics of fire damaged and rehabilitated normal
strength concrete beams through both experiments and finite element
analyses. For the experiments, control beams, fire damaged beams and
rehabilitated beams are tested to examine deformation characteristics.
Ten test beam specimens with compressive strength of 21MPa are
fabricated and main test variables are selected as cover thickness of
40mm and 50mm and fire exposure time of 1 hour or 2 hours. After
heating, fire damaged beams are air-recurred for 2 months and
rehabilitated beams are repaired with polymeric cement mortar after
being removed the fire damaged concrete cover. All beam specimens
are tested under four points loading. FE analyses are executed to
investigate the effects of main parameters applied to experimental
study. Test results show that both maximum load and stiffness of the
rehabilitated beams are higher than those of the fire damaged beams.
In addition, predicted structural behaviors from the analyses also show
good rehabilitation effect and the predicted load-deflection curves are
similar to the experimental results. For the further, the proposed
analytical method can be used to predict deformation characteristics of
fire damaged and rehabilitated concrete beams without suffering from
time and cost consuming of experimental process.
Abstract: Accurate forecasting of fresh produce demand is one
the challenges faced by Small Medium Enterprise (SME)
wholesalers. This paper is an attempt to understand the cause for the
high level of variability such as weather, holidays etc., in demand of
SME wholesalers. Therefore, understanding the significance of
unidentified factors may improve the forecasting accuracy. This
paper presents the current literature on the factors used to predict
demand and the existing forecasting techniques of short shelf life
products. It then investigates a variety of internal and external
possible factors, some of which is not used by other researchers in the
demand prediction process. The results presented in this paper are
further analysed using a number of techniques to minimize noise in
the data. For the analysis past sales data (January 2009 to May 2014)
from a UK based SME wholesaler is used and the results presented
are limited to product ‘Milk’ focused on café’s in derby. The
correlation analysis is done to check the dependencies of variability
factor on the actual demand. Further PCA analysis is done to
understand the significance of factors identified using correlation.
The PCA results suggest that the cloud cover, weather summary and
temperature are the most significant factors that can be used in
forecasting the demand. The correlation of the above three factors
increased relative to monthly and becomes more stable compared to
the weekly and daily demand.
Abstract: In this study, we demonstrate the production of natural gas hydrates from permeable marine sediments with simultaneous mechanisms for methane recovery and methane-air or methane-air/carbon dioxide replacement. The simultaneous melting happens until the chemical potentials become equal in both phases as natural gas hydrate depletion continues and self-regulated methane-air replacement occurs over an arbitrary point. We observed certain point between dissociation and replacement mechanisms in the natural gas hydrate reservoir, and we call this boundary as critical methane concentration. By the way, when carbon dioxide was added, the process of chemical exchange of methane by air/carbon dioxide was observed in the natural gas hydrate. The suggested process will operate well for most global natural gas hydrate reservoirs, regardless of the operating conditions or geometrical constraints.