Abstract: This paper presents a novel integrated hybrid
approach for fault diagnosis (FD) of nonlinear systems. Unlike most
FD techniques, the proposed solution simultaneously accomplishes
fault detection, isolation, and identification (FDII) within a unified
diagnostic module. At the core of this solution is a bank of adaptive
neural parameter estimators (NPE) associated with a set of singleparameter
fault models. The NPEs continuously estimate unknown
fault parameters (FP) that are indicators of faults in the system. Two
NPE structures including series-parallel and parallel are developed
with their exclusive set of desirable attributes. The parallel scheme is
extremely robust to measurement noise and possesses a simpler, yet
more solid, fault isolation logic. On the contrary, the series-parallel
scheme displays short FD delays and is robust to closed-loop system
transients due to changes in control commands. Finally, a fault
tolerant observer (FTO) is designed to extend the capability of the
NPEs to systems with partial-state measurement.
Abstract: Flexible AC Transmission Systems (FACTS) is
granting a new group of advanced power electronic devices emerging
for enhancement of the power system performance. Unified Power
Flow Controller (UPFC) is a recent version of FACTS devices for
power system applications. The back-up energy supply system
incorporated with UPFC is providing a complete control of real and
reactive power at the same time and hence is competent to improve
the performance of an electrical power system. In this article, backup
energy supply unit such as superconducting magnetic energy storage
(SMES) is integrated with UPFC. In addition, comparative
exploration of UPFC–battery, UPFC–UC and UPFC–SMES
performance is evaluated through the vibrant simulation by using
MATLAB/Simulink software.
Abstract: In general, codes and regulations consider seismic
loads only for completed structures of the bridges while, evaluation
of incomplete structure of bridges, especially those constructed by
free cantilever method, under these loads is also of great importance.
Hence, this research tried to study the behavior of incomplete
structure of common bridge type (box girder bridge), in construction
phase under vertical seismic loads. Subsequently, the paper provided
suitable guidelines and solutions to resist this destructive
phenomenon. Research results proved that use of preventive methods
can significantly reduce the stresses resulted from vertical seismic
loads in box cross sections to an acceptable range recommended by
design codes.
Abstract: This article focuses on upper-extremity musculoskeletal disorders risk assessment model at workplace. In this model are used risk factors that are responsible for musculoskeletal system damage. Based on statistic calculations the model is able to define what risk of MSD threatens workers who are under risk factors. The model is also able to say how MSD risk would decrease if these risk factors are eliminated.
Abstract: Freshly laid eggs from green turtles, Chelonia mydas,
were randomly collected from Ras Al-Hadd Reserve, Oman.
Eggshells taken from eggs and sand collected from the body chamber
were analyzed for eight heavy metals (Al, Br, Cd, Co, Cu, Fe, S, and
Zn) using inductively coupled plasma mass spectrometry (ICP).
Heavy metal concentrations varied significantly (P
Abstract: Traditional document representation for classification
follows Bag of Words (BoW) approach to represent the term weights.
The conventional method uses the Vector Space Model (VSM) to
exploit the statistical information of terms in the documents and they
fail to address the semantic information as well as order of the terms
present in the documents. Although, the phrase based approach
follows the order of the terms present in the documents rather than
semantics behind the word. Therefore, a semantic concept based
approach is used in this paper for enhancing the semantics by
incorporating the ontology information. In this paper a novel method
is proposed to forecast the intraday stock market price directional
movement based on the sentiments from Twitter and money control
news articles. The stock market forecasting is a very difficult and
highly complicated task because it is affected by many factors such
as economic conditions, political events and investor’s sentiment etc.
The stock market series are generally dynamic, nonparametric, noisy
and chaotic by nature. The sentiment analysis along with wisdom of
crowds can automatically compute the collective intelligence of
future performance in many areas like stock market, box office sales
and election outcomes. The proposed method utilizes collective
sentiments for stock market to predict the stock price directional
movements. The collective sentiments in the above social media have
powerful prediction on the stock price directional movements as
up/down by using Granger Causality test.
Abstract: R.C.C. buildings with dual structural system
consisting of shear walls (or braces) and moment resisting frames
have been widely used to resist lateral forces during earthquakes. The
dual systems are designed to resist the total design lateral force in
proportion to their lateral stiffness. The response of combination of
braces and shear walls has not yet been studied. The combination
may prove to be more effective to resist lateral forces during
earthquakes. This concept has been applied to regular R.C.C.
buildings provided with shear walls, braces and their combinations.
Abstract: Wireless Sensor Networks (WSNs) have wide variety
of applications and provide limitless future potentials. Nodes in
WSNs are prone to failure due to energy depletion, hardware failure,
communication link errors, malicious attacks, and so on. Therefore,
fault tolerance is one of the critical issues in WSNs. We study how
fault tolerance is addressed in different applications of WSNs. Fault
tolerant routing is a critical task for sensor networks operating in
dynamic environments. Many routing, power management, and data
dissemination protocols have been specifically designed for WSNs
where energy awareness is an essential design issue. The focus,
however, has been given to the routing protocols which might differ
depending on the application and network architecture.
Abstract: Essential oils have a significant antimicrobial activity.
These oils can successfully replace the antibiotics. So, the
microorganisms show their inefficiencies resistant for the antibiotics.
For this reason, we study the physicochemical analysis and
antimicrobial activity of the essential oil of Daucus carota. The
extraction is done by steam distillation of water which brought us a
very significant return of 4.65%. The analysis of the essential oil is
performed by GC / MS and has allowed us to identify 32 compounds
in the oil of D. carota flowering tops of Bouira. Three of which are in
the majority are the α-Pinene (22.3%), the carotol (21.7%) and the
limonene (15.8%).
Abstract: Nature is the immense gifted source for solving
complex problems. It always helps to find the optimal solution to
solve the problem. Mobile Ad Hoc NETwork (MANET) is a wide
research area of networks which has set of independent nodes. The
characteristics involved in MANET’s are Dynamic, does not depend
on any fixed infrastructure or centralized networks, High mobility.
The Bio-Inspired algorithms are mimics the nature for solving
optimization problems opening a new era in MANET. The typical
Swarm Intelligence (SI) algorithms are Ant Colony Optimization
(ACO), Artificial Bee Colony (ABC), Particle Swarm Optimization
(PSO), Modified Termite Algorithm, Bat Algorithm (BA), Wolf
Search Algorithm (WSA) and so on. This work mainly concentrated
on nature of MANET and behavior of nodes. Also it analyses various
performance metrics such as throughput, QoS and End-to-End delay
etc.
Abstract: Machining of hard materials is a recent technology for
direct production of work-pieces. The primary challenge in
machining these materials is selection of cutting tool inserts which
facilitates an extended tool life and high-precision machining of the
component. These materials are widely for making precision parts for
the aerospace industry. Nickel-based alloys are typically used in
extreme environment applications where a combination of strength,
corrosion resistance and oxidation resistance material characteristics
are required. The present paper reports the theoretical and
experimental investigations carried out to understand the influence of
machining parameters on the response parameters. Considering the
basic machining parameters (speed, feed and depth of cut) a study has
been conducted to observe their influence on material removal rate,
surface roughness, cutting forces and corresponding tool wear.
Experiments are designed and conducted with the help of Central
Composite Rotatable Design technique. The results reveals that for a
given range of process parameters, material removal rate is favorable
for higher depths of cut and low feed rate for cutting forces. Low feed
rates and high values of rotational speeds are suitable for better finish
and higher tool life.
Abstract: The effect of transition metal doping on Pt/Al2O3
catalyst used in propane dehydrogenation reaction at 500°C was
studied. The preparation methods investigated were sequential
impregnation (Pt followed by the 2nd metal or the 2nd metal followed
by Pt) and co-impregnation. The metal contents of these catalysts
were fixed as the weight ratio of Pt per the 2nd metal of around 0.075.
These catalysts were characterized by N2-physisorption, TPR, COchemisorption
and NH3-TPD. It was found that the impregnated 2nd
metal had an effect upon reducibility of Pt due to its interaction with
transition metal-containing structure. This was in agreement with the
CO-chemisorption result that the presence of Pt metal, which is a
result from Pt species reduction, was decreased. The total acidity of
bimetallic catalysts is decreased but the strong acidity is slightly
increased. It was found that the stability of bimetallic catalysts
prepared by co-impregnation and sequential impregnation where the
2nd metal was impregnated before Pt were better than that of
monometallic catalyst (undoped Pt one) due to the forming of Pt sites
located on the transition metal-oxide modified surface. Among all
preparation methods, the sequential impregnation method- having Pt
impregnated before the 2nd metal gave the worst stability because this
catalyst lacked the modified Pt sites and some fraction of Pt sites was
covered by the 2nd metal.
Abstract: Beta-glucosidase, chitinase, leucine-aminopeptidase, acid phosphomonoesterase and acetate-esterase enzyme activities in
the soils under the impact of metallurgical industrial activity in Lori
marz (district) were investigated. The results of the study showed that
the activities of the investigated enzymes in the soils decreased with increasing distance from the Shamlugh copper mine, the Chochkan
tailings storage facility and the ore transportation road. Statistical
analysis revealed that the activities of the enzymes were positively
correlated (significant) to each other according to the observation
sites which indicated that enzyme activities were affected by the
same anthropogenic factor. The investigations showed that the soils
were polluted with heavy metals (Cu, Pb, As, Co, Ni, Zn) due to
copper mining activity in this territory. The results of Pearson
correlation analysis revealed a significant negative correlation
between heavy metal pollution degree (Nemerow integrated pollution
index) and soil enzyme activity. All of this indicated that copper
mining activity in this territory causing the heavy metal pollution of
the soils resulted in the inhabitation of the activities of the enzymes
which are considered as biological catalysts to decompose organic
materials and facilitate the cycling of nutrients.
Abstract: In Jordan having deficit atmospheric precipitation, an
increase in water demand occurs during summer months. Jordan can
be regarded with a relatively high potential for wastewater recycling
and reuse. The main purpose of this paper was to investigate the
removal of total suspended solids (TSS) and chemical oxygen
demand (COD) for olive mill wastewater (OMW) by
electrocoagulation (EC) process. In the combination of
electrocoagulation by using coupled iron–aluminum electrodes, the
optimum working pH was found to be around 6. Results indicated
that the electrocoagulation process allowed removal of TSS and COD
of about 82.5% and 47.5%, respectively at 45 mA/cm2 after 70
minutes by using coupled iron–aluminum electrodes. It was
demonstrated that the maximum TSS and COD removals were
obtained at some optimum experimental parameters for current
density, pH, and reaction time.
Abstract: The heavy metal pollution degree in the soils around
the Zangezur copper and molybdenum combine in Syunik Marz,
Armenia was assessed. The results of the study showed that heavy
metal pollution degree in the soils mainly decreased with increasing
distance from the open mine and the ore enrichment combine which
indicated that the open mine and the ore enrichment combine were
the main sources of heavy metal pollution. The only exception was
observed in the northern part of the open mine where pollution
degree in the sites (along the open mine) situated 600 meters far from
the mine was higher than that in the sites located 300 meters far from
the mine. This can be explained by the characteristics of relief and air
currents as well as the weak vegetation cover of these sites and the
characteristics of soil structure. According to geo-accumulation index
(I-geo), contamination factor (Cf), contamination degree (Cd) and
pollution load index (PLI) values, the pollution degree in the soils
around the open mine and the ore enrichment combine was higher
than that in the soils around the tailing dumps which was due to the
proper and accurate operation of the Artsvanik tailing damp and the
recultivation of the Voghji tailing dump.
The high Cu and Mo pollution of the soils was conditioned by the
character of industrial activities, the moving direction of air currents
as well as the physicochemical peculiarities of the soils.
Abstract: Advances in the use of health care technology have
resulted in increased adverse events (AEs) related to the use of
medical devices. The study focused on the existing reporting systems.
This study was conducted in a tertiary care public sector hospital.
Devices included Syringe infusion pumps, Cardiac monitors, Pulse
oximeters, Ventilators and Defibrillators. A total of 211 respondents
were recruited. Interviews were held with 30 key informants. Medical
records were scrutinized. Relevant statistical tests were used.
Resident doctors reported maximum frequency of AEs, followed
by nurses; and least by consultants. A significant association was
found between the cadre of health care personnel and awareness that
the patients and bystanders have a risk of sustaining AE. Awareness
regarding reporting of AEs was low, and it was generally done
verbally. Other critical findings are discussed in the light of the
barriers to reporting, reasons for non-compliance, recording system,
and so on.
Abstract: Semiconductor crystals smaller than about 10 nm,
known as quantum dots, have properties that differ from large
samples, including a band gap that becomes larger for smaller
particles. These properties create several applications for quantum
dots. In this paper new shapes of quantum dot arrays are used to
enhance the photo physical properties of gold nano-particles. This
paper presents a study of the effect of nano-particles shape, array, and
size on their absorption characteristics.
Abstract: This work deals with parameter identification of
permanent magnet motors, a class of ac motor which is particularly
important in industrial automation due to characteristics like
applications high performance, are very attractive for applications
with limited space and reducing the need to eliminate because they
have reduced size and volume and can operate in a wide speed range,
without independent ventilation. By using experimental data and
genetic algorithm we have been able to extract values for both the
motor inductance and the electromechanical coupling constant, which
are then compared to measured and/or expected values.
Abstract: In this paper, the problem of fault detection and
isolation in the attitude control subsystem of spacecraft formation
flying is considered. In order to design the fault detection method, an
extended Kalman filter is utilized which is a nonlinear stochastic state
estimation method. Three fault detection architectures, namely,
centralized, decentralized, and semi-decentralized are designed based
on the extended Kalman filters. Moreover, the residual generation
and threshold selection techniques are proposed for these
architectures.
Abstract: Power systems are operating under stressed condition
due to continuous increase in demand of load. This can lead to
voltage instability problem when face additional load increase or
contingency. In order to avoid voltage instability suitable size of
reactive power compensation at optimal location in the system is
required which improves the load margin. This work aims at
obtaining optimal size as well as location of compensation in the 39-
bus New England system with the help of Bacteria Foraging and
Genetic algorithms. To reduce the computational time the work
identifies weak candidate buses in the system, and then picks only
two of them to take part in the optimization. The objective function is
based on a recently proposed voltage stability index which takes into
account the weighted average sensitivity index is a simpler and faster
approach than the conventional CPF algorithm. BFOA has been
found to give better results compared to GA.