Abstract: The purpose of this study was to evaluate the tissue
composition and carcass muscularity of 32 legs of Ile de France
lambs fed with diets containing sunflower seeds and vitamin E, with
mean body weight of 15 kg, lodged in individual pens at 15 kg and
slaughtered at 32 kg of body weight. The treatments influenced
(P0,05) by the treatments. The
interaction of the sunflower and vitamin E was positive for bone total
weights and intermuscular fat.
Abstract: An analysis is performed to study the influence of nonuniform double slot suction on a steady laminar boundary layer flow over a rotating sphere when fluid properties such as viscosity and Prandtl number are inverse linear functions of temperature. Nonsimilar solutions have been obtained from the starting point of the streamwise co-ordinate to the exact point of separation. The difficulties arising at the starting point of the streamwise co-ordinate, at the edges of the slot and at the point of separation have been overcome by applying an implicit finite difference scheme in combination with the quasi-linearization technique and an appropriate selection of the finer step sizes along the stream-wise direction. The present investigation shows that the point of ordinary separation can be delayed by nonuniform double slot suction if the mass transfer rate is increased and also if the slots are positioned further downstream. In addition, the investigation reveals that double slot suction is found to be more effective compared to a single slot suction in delaying ordinary separation. As rotation parameter increase the point of separation moves upstream direction.
Abstract: Design and modeling of nonlinear systems require the
knowledge of all inside acting parameters and effects. An empirical
alternative is to identify the system-s transfer function from input and
output data as a black box model. This paper presents a procedure
using least squares algorithm for the identification of a feed drive
system coefficients in time domain using a reduced model based on
windowed input and output data. The command and response of the
axis are first measured in the first 4 ms, and then least squares are
applied to predict the transfer function coefficients for this
displacement segment. From the identified coefficients, the next
command response segments are estimated. The obtained results
reveal a considerable potential of least squares method to identify the
system-s time-based coefficients and predict accurately the command
response as compared to measurements.
Abstract: The study of a real function of two real variables can be supported by visualization using a Computer Algebra System (CAS). One type of constraints of the system is due to the algorithms implemented, yielding continuous approximations of the given function by interpolation. This often masks discontinuities of the function and can provide strange plots, not compatible with the mathematics. In recent years, point based geometry has gained increasing attention as an alternative surface representation, both for efficient rendering and for flexible geometry processing of complex surfaces. In this paper we present different artifacts created by mesh surfaces near discontinuities and propose a point based method that controls and reduces these artifacts. A least squares penalty method for an automatic generation of the mesh that controls the behavior of the chosen function is presented. The special feature of this method is the ability to improve the accuracy of the surface visualization near a set of interior points where the function may be discontinuous. The present method is formulated as a minimax problem and the non uniform mesh is generated using an iterative algorithm. Results show that for large poorly conditioned matrices, the new algorithm gives more accurate results than the classical preconditioned conjugate algorithm.
Abstract: In the present work we report a gram negative
bacterial isolate, from soil of a dye industry, with promising
biorefining and bioremediation potential. This isolate (GBS.5) could
utilize carbazole (nitrogen containing polycyclic aromatic
hydrocarbon) as the sole source of nitrogen and carbon and utilize
almost 98% of 3mM carbazole in 100 hours. The specific activity of
our GBS.5 isolate for carbazole degradation at 30°C and pH 7.0 was
found to be 11.36 μmol/min/g dry cell weight as compared to 10.4
μmol/min/g dry cell weight, the highest reported specific activity till
date. The presence of car genes (the genes involved in
denitrogenation of carbazole) was confirmed through PCR
amplification.
Abstract: In India, the quarrel between the budding human
populace and the planet-s unchanging supply of freshwater and
falling water tables has strained attention the reuse of gray water as
an alternative water resource in rural development. This paper
present the finest design of laboratory scale gray water treatment
plant, which is a combination of natural and physical operations such
as primary settling with cascaded water flow, aeration, agitation and
filtration, hence called as hybrid treatment process. The economical
performance of the plant for treatment of bathrooms, basins and
laundries gray water showed in terms of deduction competency of
water pollutants such as COD (83%), TDS (70%), TSS (83%), total
hardness (50%), oil and grease (97%), anions (46%) and cations
(49%). Hence, this technology could be a good alternative to treat
gray water in residential rural area.
Abstract: The use of renewable energy sources becomes more
necessary and interesting. As wider applications of renewable energy
devices at domestic, commercial and industrial levels has not only
resulted in greater awareness, but also significantly installed
capacities. In addition, biomass principally is in the form of woods,
which is a form of energy by humans for a long time. Gasification is
a process of conversion of solid carbonaceous fuel into combustible
gas by partial combustion. Many gasifier models have various
operating conditions; the parameters kept in each model are different.
This study applied experimental data, which has three inputs, which
are; biomass consumption, temperature at combustion zone and ash
discharge rate. One output is gas flow rate. For this paper, neural
network was used to identify the gasifier system suitable for the
experimental data. In the result,neural networkis usable to attain the
answer.
Abstract: Biometric techniques are gaining importance for
personal authentication and identification as compared to the
traditional authentication methods. Biometric templates are
vulnerable to variety of attacks due to their inherent nature. When a
person-s biometric is compromised his identity is lost. In contrast to
password, biometric is not revocable. Therefore, providing security
to the stored biometric template is very crucial. Crypto biometric
systems are authentication systems, which blends the idea of
cryptography and biometrics. Fuzzy vault is a proven crypto
biometric construct which is used to secure the biometric templates.
However fuzzy vault suffer from certain limitations like nonrevocability,
cross matching. Security of the fuzzy vault is affected
by the non-uniform nature of the biometric data. Fuzzy vault when
hardened with password overcomes these limitations. Password
provides an additional layer of security and enhances user privacy.
Retina has certain advantages over other biometric traits. Retinal
scans are used in high-end security applications like access control to
areas or rooms in military installations, power plants, and other high
risk security areas. This work applies the idea of fuzzy vault for
retinal biometric template. Multimodal biometric system
performance is well compared to single modal biometric systems.
The proposed multi modal biometric fuzzy vault includes combined
feature points from retina and fingerprint. The combined vault is
hardened with user password for achieving high level of security.
The security of the combined vault is measured using min-entropy.
The proposed password hardened multi biometric fuzzy vault is
robust towards stored biometric template attacks.
Abstract: In this paper, a particle swarm optimization (PSO)
algorithm is proposed to solve machine loading problem in flexible
manufacturing system (FMS), with bicriterion objectives of
minimizing system unbalance and maximizing system throughput in
the occurrence of technological constraints such as available
machining time and tool slots. A mathematical model is used to
select machines, assign operations and the required tools. The
performance of the PSO is tested by using 10 sample dataset and the
results are compared with the heuristics reported in the literature. The
results support that the proposed PSO is comparable with the
algorithms reported in the literature.
Abstract: The wind resource in the Italian site of Lendinara
(RO) is analyzed through a systematic anemometric campaign
performed on the top of the bell tower, at an altitude of over 100 m
above the ground. Both the average wind speed and the Weibull
distribution are computed. The resulting average wind velocity is in
accordance with the numerical predictions of the Italian Wind Atlas,
confirming the accuracy of the extrapolation of wind data adopted for
the evaluation of wind potential at higher altitudes with respect to the
commonly placed measurement stations.
Abstract: This paper proposes a technique to block adult images displayed in websites. The filter is designed so as to perform even in exceptional cases such as, where face detection is not possible or improper face visibility. This is achieved by using an alternative phase to extract the MFC (Most Frequent Color) from the Human Body regions estimated using a biometric of anthropometric distances between fixed rigidly connected body locations. The logical results generated can be protected from overriding by a firewall or intrusion, by encrypting the result in a SSH data packet.
Abstract: Thermoelastic temperature, displacement, and
stress in heat transfer during laser surface hardening are solved
in Eulerian formulation. In Eulerian formulations the heat flux
is fixed in space and the workpiece is moved through a control
volume. In the case of uniform velocity and uniform heat flux
distribution, the Eulerian formulations leads to a steady-state
problem, while the Lagrangian formulations remains transient.
In Eulerian formulations the reduction to a steady-state
problem increases the computational efficiency. In this study
also an analytical solution is developed for an uncoupled
transient heat conduction equation in which a plane slab is
heated by a laser beam. The thermal result of the numerical
model is compared with the result of this analytical model.
Comparing the results shows numerical solution for uncoupled
equations are in good agreement with the analytical solution.
Abstract: Design for Disassembly (DfD) aims to reuse the
structural components instead of demolition followed by recycling of
the demolition debris. This concept preserves the invested embodied
energy of materials, thus reducing inputs of new embodied energy
during materials reprocessing or remanufacturing. Both analytical and
experimental research on a proposed DfD beam-column connection
for use in residential apartments is currently investigated at the
National University of Singapore in collaboration with the Housing
and Development Board of Singapore. The present study reports on
the results of a numerical analysis of the proposed connection utilizing
finite element analysis. The numerical model was calibrated and
validated by comparison against experimental results. Results of a
parametric study will also be presented and discussed.
Abstract: The liberalization and privatization processes have
forced public utility companies to face new competitive challenges,
implementing strategies to gain market share and, at the same time,
keep the old customers. To this end, many companies have carried
out mergers, acquisitions and conglomerations in order to diversify
their business. This paper focuses on companies operating in the free
energy market in Italy. In the last decade, this sector has undergone
profound changes that have radically changed the competitive
scenario and have led companies to implement diversification
strategies of the business. Our work aims to evaluate the economic
and financial performances obtained by energy companies, following
the beginning of the liberalization process, verifying the possible
relationship with the implemented diversification strategies.
Abstract: In the national and professional music of oral tradition
of many people in the East there is the metric formula called “ussuli",
that is to say rhythmic constructions of different character and a
composition. Ussuli in translation from Arabic means the law. The
cultural contacts of the ancient and medieval inhabitants of the
Central Asia, India, China, East Turkestan, Iraq, Afghanistan,
Turkey, and Iran have played a certain role in formation of both
musical and dancing heritage of each of these people. During
theatrical shows many dances were performed under the
accompaniment of percussion instruments as nagra, dayulpaz, doll.
The abovementioned tools are used as the obligatory accompanying
tool in an orchestra and at support of dancing acts as the solo tool.
Dynamics of development of a dancing composition, at times
execution of technique of movement depends on various
combinations of ussuli and their receptions of execution.
Abstract: In this paper, we consider components of discrete event imitating model, implementing a simulation model by using JAVA and performing an input analysis of the data and an output analysis of the simulation results. Was lead development of imitating model of mass service system with n (n≥1) devices of service. On the basis of the developed process of a multithreading simulated the distributed processes with presence of synchronization. Was developed the algorithm of event-oriented simulation, was received results of system functioning with n devices of service.
Abstract: In today-s global and competitive market,
manufacturing companies are working hard towards improving their
production system performance. Most companies develop production
systems that can help in cost reduction. Manufacturing systems
consist of different elements including production methods,
machines, processes, control and information systems. Human issues
are an important part of manufacturing systems, yet most companies
do not pay sufficient attention to them. In this paper, a workforce
planning (WP) model is presented. A non-linear programming model
is developed in order to minimize the hiring, firing, training and
overtime costs. The purpose is to determine the number of workers
for each worker type, the number of workers trained, and the number
of overtime hours. Moreover, a decision support system (DSS) based
on the proposed model is introduced using the Excel-Lingo software
interfacing feature. This model will help to improve the interaction
between the workers, managers and the technical systems in
manufacturing.
Abstract: Two short sediment cores collected from mangrove
areas of Manori and Thane creeks along Mumbai coast were analysed
for sediment composition and metals (Fe, Mn, Cu, Pb, Co, Ni, Zn, Cr
and V). The statistical analysis of Pearson correlation matrix proved
that there is a significant relationship between metal concentration
and finer grain size in Manori creek while poor correlation was
observed in Thane creek. Based on the enrichment factor, the present
metal to background metal ratios clearly reflected maximum
enrichment of Cu and Pb in Manori creek and Mn in Thane creek.
Geoaccumulation index calculated indicate that the study area is
unpolluted with respect to Fe, Mn, Co, Ni, Zn and Cr in both the
cores while moderately polluted with Cu and Pb in Manori creek.
Based on contamination degree, both the core sediments were found
to be considerably contaminated with metals.
Abstract: A four-lobe pressure dam bearing which is
produced by cutting two pressure dams on the upper two lobes and
two relief-tracks on the lower two lobes of an ordinary four-lobe
bearing is found to be more stable than a conventional four-lobe
bearing. In this paper a four-lobe pressure dam bearing supporting
rigid and flexible rotors is analytically investigated to determine its
performance when L/D ratio is varied in the range 0.75 to 1.5. The
static and dynamic characteristics are studied at various L/D ratios.
The results show that the stability of a four-lobe pressure dam
bearing increases with decrease in L/D ratios both for rigid as well as
flexible rotors.
Abstract: Deformable active contours are widely used in
computer vision and image processing applications for image
segmentation, especially in biomedical image analysis. The active
contour or “snake" deforms towards a target object by controlling the
internal, image and constraint forces. However, if the contour
initialized with a lesser number of control points, there is a high
probability of surpassing the sharp corners of the object during
deformation of the contour. In this paper, a new technique is
proposed to construct the initial contour by incorporating prior
knowledge of significant corners of the object detected using the
Harris operator. This new reconstructed contour begins to deform, by
attracting the snake towards the targeted object, without missing the
corners. Experimental results with several synthetic images show the
ability of the new technique to deal with sharp corners with a high
accuracy than traditional methods.