Abstract: Concrete is an essential building material which is
widely used in construction industry all over the world due to its
compressible strength. Curing of concrete plays a vital role in
durability and other performance necessities. Improper curing can
affect the concrete performance and durability easily. When areas
like scarcity of water, structures is not accessible by humans external
curing cannot be performed, so we opt for internal curing. Internal
curing (or) self curing plays a major role in developing the concrete
pore structure and microstructure. The concept of internal curing is to
enhance the hydration process to maintain the temperature uniformly.
The evaporation of water in the concrete is reduced by self curing
agent (Super Absorbing Polymer – SAP) there by increasing the
water retention capacity of the concrete. The research work was
carried out to reduce water, which is prime material used for concrete
in the construction industry. Concrete curing plays a major role in
developing hydration process. Concept of self curing will reduce the
evaporation of water from concrete. Self curing will increase water
retention capacity as compared to the conventional concrete. Proper
self curing (or) internal curing increases the strength, durability and
performance of concrete. Super absorbing Polymer (SAP) used as
internal curing agent. In this study 0.2% to 0.4% of SAP was varied
in different grade of high strength concrete. In the experiment
replacement of cement by silica fumes with 5%, 10% and 15% are
studied. It is found that replacement of silica fumes by 10 % gives
more strength and durability when compared to others.
Abstract: In this paper, a modified Wilkinson power divider for
GSM application is presented. The quarter–wavelength microstrip
lines in the conventional Wilkinson power divider (WPD) are
replaced by one-eighth wavelength transmission line. Wilkinson
power divider is designed using λ/4 and λ/8 transmission line. It has
the operating frequency of 915 MHz which is used in the GSM
standard. The proposed Wilkinson Power Divider is designed using
the simulation tool Advanced Design System. The results of λ/8
transmission line are very close to the results of λ/4 transmission line.
The isolation loss of λ/8 transmission line is improved by introducing
a capacitor between the output ports. The proposed Wilkinson power
divider has the best return loss of greater than -10 dB and isolation
loss of -15.25 dB. The λ/8 transmission line Wilkinson power divider
has the reduced size of 53.9 percentages than λ/4 transmission line
WPD. The proposed design has simple structure, better isolation loss
and good insertion loss.
Abstract: In wireless sensor network, sensor node transmits the
sensed data to the sink node in multi-hop communication
periodically. This high traffic induces congestion at the node which is
present one-hop distance to the sink node. The packet transmission
and reception rate of these nodes should be very high, when
compared to other sensor nodes in the network. Therefore, the energy
consumption of that node is very high and this effect is known as the
“funneling effect”. The tree based-data aggregation technique
(TBDA) is used to reduce the energy consumption of the node. The
throughput of the overall performance shows a considerable decrease
in the number of packet transmissions to the sink node. The proposed
scheme, TBDA, avoids the funneling effect and extends the lifetime
of the wireless sensor network. The average case time complexity for
inserting the node in the tree is O(n log n) and for the worst case time
complexity is O(n2).
Abstract: A Reconfigurable Wilkinson power divider is
proposed in this paper. In existing system only a limited number of
bandwidth is used at the output ports, in the proposed Wilkinson
power divider different band of frequencies are obtained by using
PIN diode. By tuning the PIN diode, different frequencies are
achieved. The size of the power divider is reduced for the operating
frequency and increases the fractional bandwidth.
Abstract: The increase in electric power demand in face of
environmental issues has intensified the participation of renewable
energy sources such as photovoltaics, in the energy matrix of various
countries. Due to their operational characteristics, they can generate
time-varying harmonic and inter-harmonic distortions. For this
reason, the application of methods of measurement based on
traditional Fourier analysis, as proposed by IEC 61000-4-7, can
provide inaccurate results. Considering the aspects mentioned herein,
came the idea of the development of this work which aims to present
the results of a comparative evaluation between a methodology
arising from the combination of the Prony method with the Kalman
filter and another method based on the IEC 61000-4-30 and IEC
61000-4-7 standards. Employed in this study were synthetic signals
and data acquired through measurements in a 50kWp photovoltaic
installation.
Abstract: Inspired by the Formula-1 competition, IMechE
(Institute of Mechanical Engineers) and Formula SAE (Society of
Mechanical Engineers) organize annual competitions for University
and College students worldwide to compete with a single-seat racecar
they have designed and built. Design of the chassis or the frame is a
key component of the competition because the weight and stiffness
properties are directly related with the performance of the car and the
safety of the driver. In addition, a reduced weight of the chassis has
direct influence on the design of other components in the car. Among
others, it improves the power to weight ratio and the aerodynamic
performance. As the power output of the engine or the battery
installed in the car is limited to 80 kW, increasing the power to
weight ratio demands reduction of the weight of the chassis, which
represents the major part of the weight of the car. In order to reduce
the weight of the car, ION Racing team from University of
Stavanger, Norway, opted for a monocoque design. To ensure
fulfilment of the competition requirements of the chassis, the
monocoque design should provide sufficient torsional stiffness and
absorb the impact energy in case of possible collision. The study reported in this article is based on the requirements for
Formula Student competition. As part of this study, diverse
mechanical tests were conducted to determine the mechanical
properties and performances of the monocoque design. Upon a
comprehensive theoretical study of the mechanical properties of
sandwich composite materials and the requirements of monocoque
design in the competition rules, diverse tests were conducted
including 3-point bending test, perimeter shear test and test for
absorbed energy. The test panels were homemade and prepared with
equivalent size of the side impact zone of the monocoque, i.e. 275
mm x 500 mm, so that the obtained results from the tests can be
representative. Different layups of the test panels with identical core
material and the same number of layers of carbon fibre were tested
and compared. Influence of the core material thickness was also
studied. Furthermore, analytical calculations and numerical analysis
were conducted to check compliance to the stated rules for Structural
Equivalency with steel grade SAE/AISI 1010. The test results were
also compared with calculated results with respect to bending and
torsional stiffness, energy absorption, buckling, etc. The obtained results demonstrate that the material composition
and strength of the composite material selected for the monocoque
design has equivalent structural properties as a welded frame and thus
comply with the competition requirements. The developed analytical
calculation algorithms and relations will be useful for future
monocoque designs with different lay-ups and compositions.
Abstract: The main purpose of this study is to assess the
sediment quality and potential ecological risk in marine sediments in
Gymea Bay located in south Sydney, Australia. A total of 32 surface
sediment samples were collected from the bay. Current track
trajectories and velocities have also been measured in the bay. The
resultant trace elements were compared with the adverse biological
effect values Effect Range Low (ERL) and Effect Range Median
(ERM) classifications. The results indicate that the average values of
chromium, arsenic, copper, zinc, and lead in surface sediments all
reveal low pollution levels and are below ERL and ERM values. The
highest concentrations of trace elements were found close to
discharge points and in the inner bay, and were linked with high
percentages of clay minerals, pyrite and organic matter, which can
play a significant role in trapping and accumulating these elements.
The lowest concentrations of trace elements were found to be on the
shoreline of the bay, which contained high percentages of sand
fractions. It is postulated that the fine particles and trace elements are
disturbed by currents and tides, then transported and deposited in
deeper areas. The current track velocities recorded in Gymea Bay had
the capability to transport fine particles and trace element pollution
within the bay. As a result, hydrodynamic measurements were able to
provide useful information and to help explain the distribution of
sedimentary particles and geochemical properties. This may lead to
knowledge transfer to other bay systems, including those in remote
areas. These activities can be conducted at a low cost, and are
therefore also transferrable to developing countries. The advent of
portable instruments to measure trace elements in the field has also
contributed to the development of these lower cost and easily applied
methodologies available for use in remote locations and low-cost
economies.
Abstract: Microcantilevers are the basic MEMS devices, which
can be used as sensors, actuators and electronics can be easily built
into them. The detection principle of microcantilever sensors is based
on the measurement of change in cantilever deflection or change in its
resonance frequency. The objective of this work is to explore the
analogies between mechanical and electrical equivalent of
microcantilever beams. Normally scientists and engineers working in
MEMS use expensive software like CoventorWare, IntelliSuite,
ANSYS/Multiphysics etc. This paper indicates the need of developing
electrical equivalent of the MEMS structure and with that, one can
have a better insight on important parameters, and their interrelation of
the MEMS structure. In this work, considering the mechanical model
of microcantilever, equivalent electrical circuit is drawn and using
force-voltage analogy, it is analyzed with circuit simulation software.
By doing so, one can gain access to powerful set of intellectual tools
that have been developed for understanding electrical circuits Later
the analysis is performed using ANSYS/Multiphysics - software based
on finite element method (FEM). It is observed that both mechanical
and electrical domain results for a rectangular microcantlevers are in
agreement with each other.
Abstract: The research on thermoelectric has been a blooming field of research for the latest decade, owing to large amount of heat source available to be harvested, being eco-friendly and static in operation. This paper provides the performance of thermoelectric generator (TEG) with bulk material of bismuth telluride, Bi2Te3. Later, the performance of the TEGs is evaluated by considering attaching the TEGs on a plastic (polyethylene sheet) in contrast to the common method of attaching the TEGs on the metal surface.
Abstract: The objective of this work is to carryout critical
comparison of different actuation mechanisms like electrostatic,
thermal, piezoelectric, and magnetic with reference to a micro
cantilever. The relevant parameters like force generated,
displacement are compared in actuation methods. With these results,
helps in choosing the best actuation method for a particular
application. In this study, Comsol/Multiphysics software is used.
Modeling and simulation is done by considering the micro cantilever
of same dimensions as an actuator using all the above mentioned
actuation techniques. In addition to their small size, micro actuators
consume very little power and are capable of accurate results. In this
work, a comparison of actuation mechanisms is done to decide the
efficient system in micro domain.
Abstract: Green concrete are generally composed of recycling
materials as hundred or partial percent substitutes for aggregate,
cement, and admixture in concrete. To reduce greenhouse gas
emissions, efforts are needed to develop environmentally friendly
construction materials. Using of fly ash based geopolymer as an
alternative binder can help reduce CO2 emission of concrete. The
binder of geopolymer concrete is different from the ordinary Portland
cement concrete. Geopolymer Concrete specimens were prepared
with different concentration of NaOH solution M10, M14, and, M16
and cured at 60ºC in duration of 24 hours and 8 hours, in addition to
the curing in direct sunlight. Thus, it is necessary to study the effects
of the geopolymer binder on the behavior of concrete. Concrete is
made by using geopolymer technology is environmental friendly and
could be considered as part of the sustainable development. In this
study, the Local Alkaline Activator in Egypt and crashed stone as
coarse aggregate in fly ash based-geopolymer concrete was
investigated. This paper illustrates the development of mechanical
properties. Since the gained compressive strength for geopolymer
concrete at 28 days was in the range of 22.5MPa – 43.9MPa.
Abstract: Local steel slag is produced as a by-product during the
oxidation of steel pellets in an electric arc furnace. Using local steel
slag waste as a hundred substitutes of crashed stone in construction
materials would resolve the environmental problems caused by the
large-scale depletion of the natural sources of crashed stone. This
paper reports the experimental study to investigate the influence of a
hundred replacement of crashed stone as a coarse aggregate with
local steel slag, on the fresh and hardened geopolymer concrete
properties. The investigation includes traditional testing of hardening
concrete, for selected mixes of cement and geopolymer concrete. It
was found that local steel slag as a coarse aggregate enhanced the
slump test of the fresh state of cement and geopolymer concretes.
Nevertheless, the unit weight of concretes was affected. Meanwhile,
the good performance was observed when fly ash used as geopolymer
concrete based.
Abstract: Heat treatable aluminum alloys such as 7075 and
7055, because of high strength and low density, are used widely in
aircraft industry. For best mechanical properties, T6 heat treatment
has recommended for this regards, but this temper treatment is
sensitive to corrosion induced and Stress Corrosion Cracking (SCC)
damage. For improving this property, the over-aging treatment (T7)
applies to this alloy, but it decreases the mechanical properties up to
30 percent. Hence, to increase the mechanical properties, without any
remarkable decrease in SCC resistant, Retrogression and Re-Aging
(RRA) heat treatment is used. This treatment performs in a relatively
short time. In this paper, the RRA heat treatment was applied to 7055
aluminum alloy and then effect of RRA time on the mechanical
properties of 7055 has been investigated. The results show that the
40-minute time is suitable time for retrogression of 7055 aluminum
alloy and ultimate strength increases up to 625MPa.
Abstract: Wireless Sensor Network (WSN) routing is complex
due to its dynamic nature, computational overhead, limited battery
life, non-conventional addressing scheme, self-organization, and
sensor nodes limited transmission range. An energy efficient routing
protocol is a major concern in WSN. LEACH is a hierarchical WSN
routing protocol to increase network life. It performs self-organizing
and re-clustering functions for each round. This study proposes a
better sensor networks cluster head selection for efficient data
aggregation. The algorithm is based on Tabu search.
Abstract: The laser-ultrasonic method is realized for
quantifying the influence of porosity on the local Young’s
modulus of isotropic composite materials. The method is based on
a laser thermooptical method of ultrasound generation combined
with measurement of the phase velocity of longitudinal and shear
acoustic waves in samples. The main advantage of this method
compared with traditional ultrasonic research methods is the
efficient generation of short and powerful probing acoustic pulses
required for reliable testing of ultrasound absorbing and
scattering heterogeneous materials. Using as an example samples
of a metal matrix composite with reinforcing microparticles of
silicon carbide in various concentrations, it is shown that to
provide an effective increase in Young’s modulus with increasing
concentration of microparticles, the porosity of the final sample
should not exceed 2%.
Abstract: The importance of agribusiness development is
proved in accordance with the trends in the agricultural sector of
Georgia. Agribusiness environment and the consequences of the
agricultural reforms are evaluated. The factors hindering the
development of agribusiness are revealed and the ways for
overcoming these problems are suggested. SWOT analysis is done in
order to identify the needs of agribusiness. The needs of agribusiness
development in Georgia are evaluated by priorities: prevention of
diseases and reduction of the harm caused by these diseases,
accessibility of long-term agricultural loans with low interest rates,
improving qualification of farmers, the level of education and usage
of modern technologies, changes in legislation, accessibility to high
quality agricultural machinery, and the development of infrastructure.
Based on the outcomes of the research, agribusiness development
strategies in Georgia are suggested and appropriate priorities of
economic policy are determined. Conclusions are made and based on
these conclusions, some recommendations are suggested.
Abstract: Brain-Computer Interfaces (BCIs) measure brain
signals activity, intentionally and unintentionally induced by users,
and provides a communication channel without depending on the
brain’s normal peripheral nerves and muscles output pathway.
Feature Selection (FS) is a global optimization machine learning
problem that reduces features, removes irrelevant and noisy data
resulting in acceptable recognition accuracy. It is a vital step
affecting pattern recognition system performance. This study presents
a new Binary Particle Swarm Optimization (BPSO) based feature
selection algorithm. Multi-layer Perceptron Neural Network
(MLPNN) classifier with backpropagation training algorithm and
Levenberg-Marquardt training algorithm classify selected features.
Abstract: Kurtbogazi Dam has gained special meaning for Ankara, Turkey for the last decade due to the rapid depletion of nearby resources of drinking water. In this study, the results of the analyses of Kurtbogazi Dam outlet water and the rivers flowing into the Kurtbogazi Dam were discussed for the period of last five years between 2008 and 2012. Some physical and chemical properties (pH, temperature, biochemical oxygen demand (BOD5), nitrate, phosphate and chlorine) of these water resources were evaluated. They were classified according to the Council Directive (75/440/EEC). Moreover, the properties of these surface waters were assessed to determine the quality of water for drinking and irrigation purposes using Piper, US Salinity Laboratory and Wilcox diagrams. The results showed that all the water resources are acceptable level as surface water except for Pazar Stream in terms of ortho-phosphate and BOD5 concentration for 2008.
Abstract: Introduction: The process to build a better safety
culture, methods of error analysis, and preventive measures, starts
with an understanding of the effects when human factors engineering
refer to remote microscopic diagnosis in surgery and specially in
organ transplantation for the remote evaluation of the grafts. It has
been estimated that even in well-organized transplant systems an
average of 8% to 14% of the grafts (G) that arrive at the recipient
hospitals may be considered as diseased, injured, damaged or
improper for transplantation. Digital microscopy adds information on
a microscopic level about the grafts in Organ Transplant (OT), and
may lead to a change in their management. Such a method will
reduce the possibility that a diseased G, will arrive at the recipient
hospital for implantation. Aim: Ergonomics of Digital Microscopy
(DM) based on virtual slides, on Telemedicine Systems (TS) for
Tele-Pathological (TPE) evaluation of the grafts (G) in organ
transplantation (OT). Material and Methods: By experimental
simulation, the ergonomics of DM for microscopic TPE of Renal
Graft (RG), Liver Graft (LG) and Pancreatic Graft (PG) tissues is
analyzed. In fact, this corresponded to the ergonomics of digital
microscopy for TPE in OT by applying Virtual Slide (VS) system for
graft tissue image capture, for remote diagnoses of possible
microscopic inflammatory and/or neoplastic lesions. Experimentation
included: a. Development of an OTE-TS similar Experimental
Telemedicine System (Exp.-TS), b. Simulation of the integration of
TS with the VS based microscopic TPE of RG, LG and PG applying
DM. Simulation of the DM based TPE was performed by 2
specialists on a total of 238 human Renal Graft (RG), 172 Liver Graft
(LG) and 108 Pancreatic Graft (PG) tissues digital microscopic
images for inflammatory and neoplastic lesions on four electronic
spaces of the four used TS. Results: Statistical analysis of specialist‘s
answers about the ability to diagnose accurately the diseased RG, LG
and PG tissues on the electronic space among four TS (A,B,C,D)
showed that DM on TS for TPE in OT is elaborated perfectly on the
ES of a Desktop, followed by the ES of the applied Exp.-TS. Tablet
and Mobile-Phone ES seem significantly risky for the application of
DM in OT (p
Abstract: Hydraulic fracturing is one of the most important
stimulation techniques available to the petroleum engineer to extract
hydrocarbons in tight gas sandstones. It allows more oil and gas
production in tight reservoirs as compared to conventional means.
The main aim of the study is to optimize the hydraulic fracturing as
technique and for this purpose three multi-zones layer formation is
considered and fractured contemporaneously. The three zones are
named as Zone1 (upper zone), Zone2 (middle zone) and Zone3
(lower zone) respectively and they all occur in shale rock. Simulation was performed with Mfrac integrated software which
gives a variety of 3D fracture options. This simulation process
yielded an average fracture efficiency of 93.8%for the three
respective zones and an increase of the average permeability of the
rock system. An average fracture length of 909 ft with net height
(propped height) of 210 ft (average) was achieved. Optimum
fracturing results was also achieved with maximum fracture width of
0.379 inches at an injection rate of 13.01 bpm with 17995 Mscf of
gas production.