Abstract: Isobaric and cooling zone of iron ore reactor have been
simulated. In this paper, heat and mass transfer equation are
formulated to perform the temperature and concentration of gas and
solid phase respectively. Temperature profile for isobaric zone is
simulated on the range temperature of 873-1163K while cooling zone
is simulated on the range temperature of 733-1139K. The simulation
results have a good agreement with the plant data. Total carbon
formation in the isobaric zone is only 30% of total carbon contained in
the sponge iron product. The formation of Fe3C in isobaric zone
reduces metallization degree up to 0.58% whereas reduction of
metallization degree in cooling zone up to 1.139%. The decreasing of
sponge iron temperature in the isobaric and cooling zone is around 300
K and 600 K respectively.
Abstract: Large metal and concrete structures suffer by various kinds of deterioration, and accurate prediction of the remaining life is important. This paper informs about two methods for its assessment. One method, suitable for steel bridges and other constructions exposed to fatigue, monitors the loads and damage accumulation using information systems for the operation and the finite element model of the construction. In addition to the operation load, the dead weight of the construction and thermal stresses can be included into the model. The second method is suitable for concrete bridges and other structures, which suffer by carbonatation and other degradation processes, driven by diffusion. The diffusion constant, important for the prediction of future development, can be determined from the depth-profile of pH, obtained by pH measurement at various depths. Comparison with measurements on real objects illustrates the suitability of both methods.
Abstract: Overall cost is a significant consideration in any
decision-making process. Although many studies were carried out on
overall cost in construction, little has treated the uncertainties of real
life cycle development. On the basis of several case studies, a
feedback process was performed on the historical data of studied
buildings. This process enabled to identify some factors causing
uncertainty during the operational period. As a result, the research
proposes a new method for assessing the overall cost during a part of
the building-s life cycle taking account of the building actual value,
its end-of-life value and the influence of the identified life cycle
uncertainty factors. The findings are a step towards a higher level of
reliability in overall cost evaluation taking account of some usually
unexpected uncertainty factors.
Abstract: With the necessity of increased processing capacity with less energy consumption; power aware multiprocessor system has gained more attention in the recent future. One of the additional challenges that is to be solved in a multi-processor system when compared to uni-processor system is job allocation. This paper presents a novel task dependent job allocation algorithm: Energy centric- Allocation (Ec-A) and Rate Monotonic (RM) scheduling to minimize energy consumption in a multiprocessor system. A simulation analysis is carried out to verify the performance increase with reduction in energy consumption and required number of processors in the system.
Abstract: Technology assessment is a vital part of decision process in manufacturing, particularly for decisions on selection of new sustainable manufacturing processes. To assess these processes, a matrix approach is introduced and sustainability assessment models are developed. Case studies show that the matrix-based approach provides a flexible and practical way for sustainability evaluation of new manufacturing technologies such as those used in surface coating. The technology assessment of coating processes reveals that compared with powder coating, the sol-gel coating can deliver better technical, economical and environmental sustainability with respect to the selected sustainability evaluation criteria for a decorative coating application of car wheels.
Abstract: In this paper, a new method of controlling position of AC Servomotor using Field Programmable Gate Array (FPGA). FPGA controller is used to generate direction and the number of pulses required to rotate for a given angle. Pulses are sent as a square wave, the number of pulses determines the angle of rotation and frequency of square wave determines the speed of rotation. The proposed control scheme has been realized using XILINX FPGA SPARTAN XC3S400 and tested using MUMA012PIS model Alternating Current (AC) servomotor. Experimental results show that the position of the AC Servo motor can be controlled effectively. KeywordsAlternating Current (AC), Field Programmable Gate Array (FPGA), Liquid Crystal Display (LCD).
Abstract: Hydrodynamic pressures acting on upstream of concrete dams during an earthquake are an important factor in designing and assessing the safety of these structures in Earthquake regions. Due to inherent complexities, assessing exact hydrodynamic pressure is only feasible for problems with simple geometry. In this research, the governing equation of concrete gravity dam reservoirs with effect of fluid viscosity in frequency domain is solved and then compared with that in which viscosity is assumed zero. The results show that viscosity influences the reservoir-s natural frequency. In excitation frequencies near the reservoir's natural frequencies, hydrodynamic pressure has a considerable difference in compare to the results of non-viscose fluid.
Abstract: A proposed small-signal model parameters for a pseudomorphic high electron mobility transistor (PHEMT) is presented. Both extrinsic and intrinsic circuit elements of a smallsignal model are determined using genetic algorithm (GA) as a stochastic global search and optimization tool. The parameters extraction of the small-signal model is performed on 200-μm gate width AlGaAs/InGaAs PHEMT. The equivalent circuit elements for a proposed 18 elements model are determined directly from the measured S- parameters. The GA is used to extract the parameters of the proposed small-signal model from 0.5 up to 18 GHz.
Abstract: Investigations of the unimolecular decomposition of
vinyl ethyl ether (VEE), vinyl propyl ether (VPE) and vinyl butyl
ether (VBE) have shown that activation of the molecule of a ether
results in formation of a cyclic construction - the transition state (TS),
which may lead to the displacement of the thermodynamic
equilibrium towards the reaction products. The TS is obtained by
applying energy minimization relative to the ground state of an ether
under the program MM2 when taking into account the hydrogen bond
formation between a hydrogen atom of alkyl residue and the extreme
atom of carbon of the vinyl group. The dissociation of TS up to the
products is studied by energy minimization procedure using the
mathematical program Gaussian. The obtained calculation data for
VEE testify that the decomposition of this ether may be conditioned
by hydrogen bond formation for two possible versions: when α- or β-
hydrogen atoms of the ethyl group are bound to carbon atom of the
vinyl group. Applying the same calculation methods to other ethers
(VPE and VBE) it is shown that only in the case of hydrogen bonding
between α-hydrogen atom of the alkyl residue and the extreme atom
of carbon of the vinyl group (αH---C) results in decay of theses
ethers.
Abstract: The fundamental aim of extended expansion concept is
to achieve higher work done which in turn leads to higher thermal
efficiency. This concept is compatible with the application of
turbocharger and LHR engine. The Low Heat Rejection engine was
developed by coating the piston crown, cylinder head inside with
valves and cylinder liner with partially stabilized zirconia coating of
0.5 mm thickness. Extended expansion in diesel engines is termed as
Miller cycle in which the expansion ratio is increased by reducing the
compression ratio by modifying the inlet cam for late inlet valve
closing. The specific fuel consumption reduces to an appreciable level
and the thermal efficiency of the extended expansion turbocharged
LHR engine is improved.
In this work, a thermodynamic model was formulated and
developed to simulate the LHR based extended expansion
turbocharged direct injection diesel engine. It includes a gas flow
model, a heat transfer model, and a two zone combustion model. Gas
exchange model is modified by incorporating the Miller cycle, by
delaying inlet valve closing timing which had resulted in considerable
improvement in thermal efficiency of turbocharged LHR engines. The
heat transfer model, calculates the convective and radiative heat
transfer between the gas and wall by taking into account of the
combustion chamber surface temperature swings. Using the two-zone
combustion model, the combustion parameters and the chemical
equilibrium compositions were determined. The chemical equilibrium
compositions were used to calculate the Nitric oxide formation rate by
assuming a modified Zeldovich mechanism. The accuracy of this
model is scrutinized against actual test results from the engine. The
factors which affect thermal efficiency and exhaust emissions were
deduced and their influences were discussed. In the final analysis it is
seen that there is an excellent agreement in all of these evaluations.
Abstract: This paper presents a new heuristic algorithm for the classical symmetric traveling salesman problem (TSP). The idea of the algorithm is to cut a TSP tour into overlapped blocks and then each block is improved separately. It is conjectured that the chance of improving a good solution by moving a node to a position far away from its original one is small. By doing intensive search in each block, it is possible to further improve a TSP tour that cannot be improved by other local search methods. To test the performance of the proposed algorithm, computational experiments are carried out based on benchmark problem instances. The computational results show that algorithm proposed in this paper is efficient for solving the TSPs.
Abstract: Noble metal participation in nanostructured
semiconductor catalysts has drawn much interest because of their
improved properties. Recently, it has been discussed by many
researchers that Ag participation in TiO2, CuO, ZnO semiconductors
showed improved photocatalytic and optical properties. In this
research, Ag/ZnO nanocomposite particles were prepared by
Ultrasonic Spray Pyrolysis(USP) Method. 0.1M silver and zinc
nitrate aqueous solutions were used as precursor solutions. The
Ag:Zn atomic ratio of the solution was selected 1:1. Experiments
were taken place under constant air flow of 400 mL/min at 800°C
furnace temperature. Particles were characterized by X-Ray
Diffraction (XRD), Scanning Electron Microscope (SEM) and
Energy Dispersive Spectroscopy (EDS). The crystallite sizes of Ag
and ZnO in composite particles are 24.6 nm, 19.7 nm respectively.
Although, spherical nanocomposite particles are in a range of 300-
800 nm, these particles are formed by the aggregation of primary
particles which are in a range of 20-60 nm.
Abstract: Efficient luminescence is reported for the first time in Eu2+ activated double Chlorides A2BCl4 (A=Alkali metal, B=Alkaline earth element). A simple wet-chemical preparation is described. Emission intensities are comparable to that of the commercial phosphor. Excitation covers near UV region. These phosphors may be useful for applications like solid state lighting, scintillation detectors and X-ray storage using photo-stimulable phosphors.
Abstract: Saturated hydraulic conductivity is one of the soil
hydraulic properties which is widely used in environmental studies
especially subsurface ground water. Since, its direct measurement is
time consuming and therefore costly, indirect methods such as
pedotransfer functions have been developed based on multiple linear
regression equations and neural networks model in order to estimate
saturated hydraulic conductivity from readily available soil
properties e.g. sand, silt, and clay contents, bulk density, and organic
matter. The objective of this study was to develop neural networks
(NNs) model to estimate saturated hydraulic conductivity from
available parameters such as sand and clay contents, bulk density,
van Genuchten retention model parameters (i.e. r
θ , α , and n) as well
as effective porosity. We used two methods to calculate effective
porosity: : (1) eff s FC φ =θ -θ , and (2) inf φ =θ -θ eff s , in which s
θ is
saturated water content, FC θ is water content retained at -33 kPa
matric potential, and inf θ is water content at the inflection point.
Total of 311 soil samples from the UNSODA database was divided
into three groups as 187 for the training, 62 for the validation (to
avoid over training), and 62 for the test of NNs model. A commercial
neural network toolbox of MATLAB software with a multi-layer
perceptron model and back propagation algorithm were used for the
training procedure. The statistical parameters such as correlation
coefficient (R2), and mean square error (MSE) were also used to
evaluate the developed NNs model. The best number of neurons in
the middle layer of NNs model for methods (1) and (2) were
calculated 44 and 6, respectively. The R2 and MSE values of the test
phase were determined for method (1), 0.94 and 0.0016, and for
method (2), 0.98 and 0.00065, respectively, which shows that method
(2) estimates saturated hydraulic conductivity better than method (1).
Abstract: Electro Discharge Sawing is a hybrid process
combining the features of SEDM and ECM. Its major characteristic is
extremely fast erosion rate compare to either of the above processes.
This paper brings out its relative feature of SEDM and EDS about
their erosion rates, surface roughness, and morphology of machined
surfaces.
Abstract: In this paper, a nonlinear acoustic echo cancellation
(AEC) system is proposed, whereby 3rd order Volterra filtering is
utilized along with a variable step-size Gauss-Seidel pseudo affine
projection (VSSGS-PAP) algorithm. In particular, the proposed
nonlinear AEC system is developed by considering a double-talk
situation with near-end signal variation. Simulation results
demonstrate that the proposed approach yields better nonlinear AEC
performance than conventional approaches.
Abstract: In the past few years, the use of wireless sensor networks (WSNs) potentially increased in applications such as intrusion detection, forest fire detection, disaster management and battle field. Sensor nodes are generally battery operated low cost devices. The key challenge in the design and operation of WSNs is to prolong the network life time by reducing the energy consumption among sensor nodes. Node clustering is one of the most promising techniques for energy conservation. This paper presents a novel clustering algorithm which maximizes the network lifetime by reducing the number of communication among sensor nodes. This approach also includes new distributed cluster formation technique that enables self-organization of large number of nodes, algorithm for maintaining constant number of clusters by prior selection of cluster head and rotating the role of cluster head to evenly distribute the energy load among all sensor nodes.
Abstract: In this research, a systematic investigation was carried out to determine the optimum conditions of HDS reactor. Moreover, a suitable model was developed for a rigorous RTO (real time optimization) loop of HDS (Hydro desulfurization) process. A systematic experimental series was designed based on CCD (Central Composite design) and carried out in the related pilot plant to tune the develop model. The designed variables in the experiments were Temperature, LHSV and pressure. However, the hydrogen over fresh feed ratio was remained constant. The ranges of these variables were respectively equal to 320-380ºC, 1- 21/hr and 50-55 bar. a power law kinetic model was also developed for our further research in the future .The rate order and activation energy , power of reactant concentration and frequency factor of this model was respectively equal to 1.4, 92.66 kJ/mol and k0=2.7*109 .
Abstract: In this paper we present our results on the performance analysis of a multi-product manufacturing line. We study the influence of external perturbations, intermediate buffer content and the number of manufacturing stages on the production tracking error of each machine in the multi-product line operated under a surplusbased production control policy. Starting by the analysis of a single machine with multiple production stages (one for each product type), we provide bounds on the production error of each stage. Then, we extend our analysis to a line of multi-stage machines, where similarly, bounds on each production tracking error for each product type, as well as buffer content are obtained. Details on performance of the closed-loop flow line model are illustrated in numerical simulations.
Abstract: In this paper, we propose a new class of Volterra series based filters for image enhancement and restoration. Generally the linear filters reduce the noise and cause blurring at the edges. Some nonlinear filters based on median operator or rank operator deal with only impulse noise and fail to cancel the most common Gaussian distributed noise. A class of second order Volterra filters is proposed to optimize the trade-off between noise removal and edge preservation. In this paper, we consider both the Gaussian and mixed Gaussian-impulse noise to test the robustness of the filter. Image enhancement and restoration results using the proposed Volterra filter are found to be superior to those obtained with standard linear and nonlinear filters.