Abstract: The aim of this retrospective study was to evaluate the
parameters of dental implants such as patient gender, number of
implant, failed implant before prosthetic restorations and failed
implant after implantation and failed implant after prosthetic
restorations. 135 male and 99 female patients, total 234 implant
patients which have been treated with 450 implant between 2005-
2009 years in GATA Haydarpasa Training Hospital Dental Service.
Twelve implants were failed before prosthetic restorations. Four
implant were failed after fixed prosthetic restorations. Cumulative
survival rate after prostheses were 97.56 % during 6 years period.
Abstract: Nowadays, new home appliances and office appliances
have been developed that communicate with users through the
Internet, for remote monitor and remote control. However, developments
and sales of these new appliances are just started, then,
many products in our houses and offices do not have these useful
functions. In few years, we add these new functions to the outlet,
it means multifunctional electrical power socket plug adapter. The
outlet measure power consumption of connecting appliances, and it
can switch power supply to connecting appliances, too. Using this
outlet, power supply of old appliances can be control and monitor.
And we developed the interface system using web browser to operate
it from users[1]. But, this system need to set up LAN cables between
outlets and so on. It is not convenience that cables around rooms. In
this paper, we develop the system that use wireless mobile ad hoc
network instead of wired LAN to communicate with the outlets.
Abstract: The composite materials were prepared by sawdust, cassava starch and natural rubber latex (NR). The mixtures of 15%w/v gelatinized cassava starch and 15%w/v PVOH were used as the binder of these composite materials. The concentrated rubber latex was added to the mixtures. They were mixed rigorously to the treated sawdust in the ratio of 70:30 until achive uniform dispersion. The batters were subjected to the hot compression moulding at the temperature of 160°C and 3,000 psi pressure for 5 min. The experimental results showed that the mechanical properties of composite materials, which contained the gelatinized cassava starch and PVOH in the ratio of 2:1, 20% NR latex by weight of the dry starch and treated sawdust with 5%NaOH or 1% BPO, were the best. It contributed the maximal compression strength (341.10 + 26.11 N), puncture resistance (8.79 + 0.98 N/mm2) and flexural strength (3.99 + 0.72N/mm2). It is also found that the physicochemical and mechanical properties of composites strongly depends on the interface quality of sawdust, cassava starch and NR latex.
Abstract: The Petri net tool INA is a well known tool by the
Petri net community. However, it lacks a graphical environment to
cerate and analyse INA models. Building a modelling tool for the
design and analysis from scratch (for INA tool for example) is
generally a prohibitive task. Meta-Modelling approach is useful to
deal with such problems since it allows the modelling of the
formalisms themselves. In this paper, we propose an approach based
on the combined use of Meta-modelling and Graph Grammars to
automatically generate a visual modelling tool for INA for analysis
purposes. In our approach, the UML Class diagram formalism is
used to define a meta-model of INA models. The meta-modelling
tool ATOM3 is used to generate a visual modelling tool according to
the proposed INA meta-model. We have also proposed a graph
grammar to automatically generate INA description of the
graphically specified Petri net models. This allows the user to avoid
the errors when this description is done manually. Then the INA tool
is used to perform the simulation and the analysis of the resulted INA
description. Our environment is illustrated through an example.
Abstract: This paper describes part of a project about Learningby-
Modeling (LbM). Studying complex systems is increasingly
important in teaching and learning many science domains. Many
features of complex systems make it difficult for students to develop
deep understanding. Previous research indicates that involvement
with modeling scientific phenomena and complex systems can play a
powerful role in science learning. Some researchers argue with this
view indicating that models and modeling do not contribute to
understanding complexity concepts, since these increases the
cognitive load on students. This study will investigate the effect of
different modes of involvement in exploring scientific phenomena
using computer simulation tools, on students- mental model from the
perspective of structure, behavior and function. Quantitative and
qualitative methods are used to report about 121 freshmen students
that engaged in participatory simulations about complex phenomena,
showing emergent, self-organized and decentralized patterns. Results
show that LbM plays a major role in students' concept formation
about complexity concepts.
Abstract: Optimization of cutting parameters important in precision machining in regards to efficiency and surface integrity of the machined part. Usually productivity and precision in machining is limited by the forces emanating from the cutting process. Due to the inherent varying nature of the workpiece in terms of geometry and material composition, the peak cutting forces vary from point to point during machining process. In order to increase productivity without compromising on machining accuracy, it is important to control these cutting forces. In this paper a fuzzy logic control algorithm is developed that can be applied in the control of peak cutting forces in milling of spherical surfaces using ball end mills. The controller can adaptively vary the feedrate to maintain allowable cutting force on the tool. This control algorithm is implemented in a computer numerical control (CNC) machine. It has been demonstrated that the controller can provide stable machining and improve the performance of the CNC milling process by varying feedrate.
Abstract: The main objective of the paper has been represented
by the identification of the changes that occurred in the competitive
environment and their impact on the strategic marketing management
of companies in B2B market. At Romania-s level there has not yet
been done a similar research that studies change management in
crises on business to business field. In order to answer to the paper-s
objectives, a qualitative marketing research (in-depth structured
interview) was conducted, within the top management of 27
companies in Romanian business to business field. The main results
of the research highlight the necessity of a management of change, as
a result of the crises, as follows: changes in the corporate objectives
(from development objectives to maintaining objectives), changes
market segmentation and in competitive advantages, changes at the
level of market strategies and of the marketing mix.
Abstract: UK breweries generate extensive by products in the
form of spent grain, slurry and yeast. Much of the spent grain is
produced by large breweries and processed in bulk for animal feed.
Spent brewery grains contain up to 20% protein dry weight and up to
60% fiber and are useful additions to animal feed. Bulk processing is
economic and allows spent grain to be sold so providing an income
to the brewery. A proportion of spent grain, however, is produced by
small local breweries and is more variably distributed to farms or
other users using intermittent collection methods. Such use is much
less economic and may incur losses if not carefully assessed for
transport costs. This study reports an economic returns of using wet
brewery spent grain (WBSG) in animal feed using the Co-product
Optimizer Decision Evaluator model (Cattle CODE) developed by
the University of Nebraska to predict performance and economic
returns when byproducts are fed to finishing cattle. The results
indicated that distance from brewery to farm had a significantly
greater effect on the economics of use of small brewery spent grain
and that alternative uses than cattle feed may be important to
develop.
Abstract: The Yasuj city stream named the Beshar supply
water for different usages such as aquaculture farms , drinking,
agricultural and industrial usages. Fish processing plants
,Agricultural farms, waste water of industrial zones and hospitals
waste water which they are generate by human activity produce a
considerable volume of effluent and when they are released in to the
stream they can effect on the water quality and down stream aquatic
systems. This study was conducted to evaluate the effects of outflow
effluent from different human activity and point and non point
pollution sources on the water quality and health of the Beshar
river next to Yasuj. Yasuj is the biggest and most important city in
the Kohkiloye and Boyerahmad province . The Beshar River is one
of the most important aquatic ecosystems in the upstream of the
Karun watershed in south of Iran which is affected by point and non
point pollutant sources . This study was done in order to evaluate the
effects of human activities on the water quality and health of the
Beshar river. This river is approximately 190 km in length and
situated at the geographical positions of 51° 20' to 51° 48' E and 30°
18' to 30° 52' N it is one of the most important aquatic ecosystems of
Kohkiloye and Boyerahmad province in south-west Iran. In this
research project, five study stations were selected to examine water
pollution in the Beshar River systems. Human activity is now one of
the most important factors affecting on hydrology and water quality
of the Beshar river. Humans use large amounts of resources to sustain
various standards of living, although measures of sustainability are
highly variable depending on how sustainability is defined. The
Beshar river ecosystems are particularly sensitive and vulnerable to
human activities. The water samples were analyzed, then some
important water quality parameters such as pH, dissolve oxygen
(DO), Biochemical Oxygen Demand (BOD5), Chemical Oxygen
Demand (COD), Total Suspended Solids (TDS),Turbidity,
Temperature, Nitrates (NO3) and Phosphates (PO4) were estimated
at the two stations. The results show a downward trend in the water
quality at the down stream of the city. The amounts of
BOD5,COD,TSS,T,Turbidity, NO3 and PO4 in the down stream
stations were considerably more than the station 1. By contrast the
amounts of DO in the down stream stations were less than to the
station 1. However when effluent discharge consequence of human
activities are released into the Beshar river near the city, the quality
of river are decreases and the environmental problems of the river
during the next years are predicted to rise.
Abstract: The primary objective of this paper was to construct a
“kinematic parameter-independent modeling of three-axis machine
tools for geometric error measurement" technique. Improving the
accuracy of the geometric error for three-axis machine tools is one of
the machine tools- core techniques. This paper first applied the
traditional method of HTM to deduce the geometric error model for
three-axis machine tools. This geometric error model was related to the
three-axis kinematic parameters where the overall errors was relative
to the machine reference coordinate system. Given that the
measurement of the linear axis in this model should be on the ideal
motion axis, there were practical difficulties. Through a measurement
method consolidating translational errors and rotational errors in the
geometric error model, we simplified the three-axis geometric error
model to a kinematic parameter-independent model. Finally, based on
the new measurement method corresponding to this error model, we
established a truly practical and more accurate error measuring
technique for three-axis machine tools.
Abstract: Unified Modeling language (UML) is one of the
important modeling languages used for the visual representation of
the research problem. In the present paper, UML model is designed
for the Instruction pipeline which is used for the evaluation of the
instructions of software programs. The class and sequence diagrams
are designed & performance is evaluated for instructions of a sample
program through a case study.
Abstract: The purpose of this paper is to present the fuzzy contraction
properties of the Hutchinson-Barnsley operator on the fuzzy
hyperspace with respect to the Hausdorff fuzzy metrics. Also we
discuss about the relationships between the Hausdorff fuzzy metrics
on the fuzzy hyperspaces. Our theorems generalize and extend some
recent results related with Hutchinson-Barnsley operator in the metric
spaces.
Abstract: Adopting the measured constitutive relationship of
stress-strain of river ice, the finite element analysis model of
percussive force of river ice and pier is established, by the explicit
dynamical analysis software package LS-DYNA. Effects of element
types, contact method and arithmetic of ice and pier, coupled modes
between different elements, mesh density of pier, and ice sheet in
contact area on the collision force are studied. Some of measures for
the collision force analysis of river ice and pier are proposed as
follows: bridge girder can adopt beam161 element with 3-node; pier
below the line of 1.30m above ice surface and ice sheet use solid164
element with 8-node; in order to accomplish the connection of
different elements, the rigid body with 0.01-0.05m thickness is defined
between solid164 and beam161; the contact type of ice and pier adopts
AUTOMATIC_SURFACE_TO_SURFACE, using symmetrical
penalty function algorithms; meshing size of pier below the line of
1.30m above ice surface should not less than 0.25×0.25×0.5m3. The
simulation results have the advantage of high precision by making a
comparison between measured and computed data. The research
results can be referred for collision force study between river ice and
pier.
Abstract: Shadows add great amount of realism to a scene and
many algorithms exists to generate shadows. Recently, Shadow
volumes (SVs) have made great achievements to place a valuable
position in the gaming industries. Looking at this, we concentrate on
simple but valuable initial partial steps for further optimization in SV
generation, i.e.; model simplification and silhouette edge detection
and tracking. Shadow volumes (SVs) usually takes time in generating
boundary silhouettes of the object and if the object is complex then
the generation of edges become much harder and slower in process.
The challenge gets stiffer when real time shadow generation and
rendering is demanded. We investigated a way to use the real time
silhouette edge detection method, which takes the advantage of
spatial and temporal coherence, and exploit the level-of-details
(LOD) technique for reducing silhouette edges of the model to use
the simplified version of the model for shadow generation speeding
up the running time. These steps highly reduce the execution time of
shadow volume generations in real-time and are easily flexible to any
of the recently proposed SV techniques. Our main focus is to exploit
the LOD and silhouette edge detection technique, adopting them to
further enhance the shadow volume generations for real time
rendering.
Abstract: WOLED is widely used as lighting for high efficacy and little power consumption. In this research, power factor testing between WOLED and fluorescent lamp to see which one is more efficient in consuming energy. Since both lamps use semiconductor components, so calculation of the power factor need to consider the effects of harmonics. Harmonic make bigger losses. The study is conducted by comparing the value of the power factor regardless of harmonics (DPF) and also by included the harmonics (TPF). The average value of DPF of fluorescent is 0.953 while WOLED is 0.972. The average value of TPF of fluorescent is 0.717 whereas WOLED is 0.933. So from the review of power factor WOLED is more energy efficient than fluorescent lamp.
Abstract: A typical definition of the Computer Aided Diagnosis
(CAD), found in literature, can be: A diagnosis made by a radiologist
using the output of a computerized scheme for automated image
analysis as a diagnostic aid. Often it is possible to find the expression
Computer Aided Detection (CAD or CADe): this definition
emphasizes the intent of CAD to support rather than substitute the
human observer in the analysis of radiographic images. In this article
we will illustrate the application of CAD systems and the aim of
these definitions.
Commercially available CAD systems use computerized
algorithms for identifying suspicious regions of interest. In this paper
are described the general CAD systems as an expert system
constituted of the following components: segmentation / detection,
feature extraction, and classification / decision making.
As example, in this work is shown the realization of a Computer-
Aided Detection system that is able to assist the radiologist in
identifying types of mammary tumor lesions. Furthermore this
prototype of station uses a GRID configuration to work on a large
distributed database of digitized mammographic images.
Abstract: Pressures for urban redevelopment are intensifying in
all large cities. A new logic for urban development is required –
green urbanism – that provides a spatial framework for directing
population and investment inwards to brownfields and greyfields
precincts, rather than outwards to the greenfields. This represents
both a major opportunity and a major challenge for city planners in
pluralist liberal democracies. However, plans for more compact
forms of urban redevelopment are stalling in the face of community
resistance. A new paradigm and spatial planning platform is required
that will support timely multi-level and multi-actor stakeholder
engagement, resulting in the emergence of consensus plans for
precinct-level urban regeneration capable of more rapid
implementation. Using Melbourne, Australia as a case study, this
paper addresses two of the urban intervention challenges – where and
how – via the application of a 21st century planning tool ENVISION
created for this purpose.
Abstract: This work examines thermal convection in two porous
layers. Flow in the upper layer is governed by Brinkman-s equations
model and in the lower layer is governed by Darcy-s model.
Legendre polynomials are used to obtain numerical solution when the
lower layer is heated from below.
Abstract: In this work a dual laser triangulation system is presented for fast building of 2.5D textured models of objects within a production line. This scanner is designed to produce data suitable for 3D completeness inspection algorithms. For this purpose two laser projectors have been used in order to considerably reduce the problem of occlusions in the camera movement direction. Results of reconstruction of electronic boards are presented, together with a comparison with a commercial system.
Abstract: The paper presents a method for multivariate time
series forecasting using Independent Component Analysis (ICA), as a preprocessing tool. The idea of this approach is to do the forecasting in the space of independent components (sources), and then to transform back the results to the original time series
space. The forecasting can be done separately and with a different
method for each component, depending on its time structure. The
paper gives also a review of the main algorithms for independent component analysis in the case of instantaneous mixture models, using second and high-order statistics. The method has been applied in simulation to an artificial multivariate time series
with five components, generated from three sources and a mixing matrix, randomly generated.