Abstract: A transient three-dimensional computational fluid dynamics (CFD) model is developed to determine the velocity and temperature distribution in different positions cold room during pre-cooling of dates. The turbulence model used is the k-ω Shear Stress Transport (SST) with the standard wall function, the air. The numerical results obtained show that cooling rate is not uniform inside the room; the product at the medium of room has a slower cooling rate. This cooling heterogeneity has a large effect on the energy consumption during cold storage.
Abstract: The heat flow in weldment changes its nature from 2D to 3D with the increase in plate thickness. For welding of thicker plates the heat loss in thickness direction increases the cooling rate of plate. Since the cooling rate changes, the various bead parameters like bead penetration, bead height and bead width also got affected by it. The present study incorporates the effect of variable plate thickness on penetration and bead width. The penetration reduces with increase in plate thickness due to heat loss in thickness direction for same heat input, while bead width increases for thicker plate due to faster cooling.
Abstract: In this current contribution, authors are dedicated to
investigate influence of the crystal lamellae orientation on
electromechanical behaviors of relaxor ferroelectric Poly
(vinylidene fluoride –trifluoroethylene -chlorotrifluoroethylene)
(P(VDF-TrFE-CTFE)) films by control of polymer microstructure,
aiming to picture the full map of structure-property relationship. In
order to define their crystal orientation films, terpolymer films were
fabricated by solution-casting, stretching and hot-pressing process.
Differential scanning calorimetry, impedance analyzer, and tensile
strength techniques were employed to characterize crystallographic
parameters, dielectric permittivity, and elastic Young’s modulus
respectively. In addition, large electrical induced out-of-plane
electrostrictive strain was obtained by cantilever beam mode.
Consequently, as-casted pristine films exhibited surprisingly high
electrostrictive strain 0.1774% due to considerably small value of
elastic Young’s modulus although relatively low dielectric
permittivity. Such reasons contributed to large mechanical elastic
energy density. Instead, due to 2 folds increase of elastic Young’s
modulus and less than 50% augmentation of dielectric constant, fullycrystallized
film showed weak electrostrictive behavior and
mechanical energy density as well. And subjected to mechanical
stretching process, Film C exhibited stronger dielectric constant and
out-performed electrostrictive strain over Film B because edge-on
crystal lamellae orientation induced by uniaxially mechanical stretch.
Hot-press films were compared in term of cooling rate. Rather large
electrostrictive strain of 0.2788% for hot-pressed Film D in
quenching process was observed although its dielectric permittivity
equivalent to that of pristine as-casted Film A, showing highest
mechanical elastic energy density value of 359.5 J/m3. In hot-press
cooling process, dielectric permittivity of Film E saw values at 48.8
concomitant with ca.100% increase of Young’s modulus. Films with
intermediate mechanical energy density were obtained.
Abstract: In this research article a comprehensive investigation
has been carried out to determine the effect of thermal cycle on
temperature dependent process parameters developed during gas
tungsten arc (GTA) welding of high carbon (AISI 1090) steel butt
joints. An experiment based thermal analysis has been performed to
obtain the thermal history. We have focused on different
thermophysical properties such as thermal conductivity, heat transfer
coefficient and cooling rate. Angular torch model has been utilized to
find out the surface heat flux and its variation along the fusion zone as
well as along the longitudinal direction from fusion boundary. After
welding and formation of weld pool, heat transfer coefficient varies
rapidly in the vicinity of molten weld bead and heat affected zone. To
evaluate the heat transfer coefficient near the fusion line and near the
rear end of the plate (low temperature region), established correlation
has been implemented and has been compared with empirical
correlation which is noted as coupled convective and radiation heat
transfer coefficient. Change in thermal conductivity has been
visualized by analytical model of moving point heat source. Rate of
cooling has been estimated by using 2-dimensional mathematical
expression of cooling rate and it has shown good agreement with
experimental temperature cycle. Thermophysical properties have been
varied randomly within 0 -10s time span.