Abstract: Recently increasing oil production from petroleum reservoirs is one of the most important issues in the global energy sector. So, in this paper, the recovery of oil by the waterflooding technique from petroleum reservoir are considered. To investigate the aforementioned phenomena, the relative permeability of two immiscible fluids in sand is measured in the laboratory based on the steady-state method. Two sorts of oils, kerosene and heavy oil, and water are pumped simultaneously into a vertical sand column with different pumping ratio. From the change in fractional discharge measured at the outlet, a method for determining the relative permeability is developed focusing on the displacement mechanism in sand. Then, displacement mechanism of two immiscible fluids in the sand is investigated under the Buckley-Leveret frontal displacement theory and laboratory experiment. Two sorts of experiments, one is the displacement of pore water by oil, the other is the displacement of pore oil by water, are carried out. It is revealed that the relative permeability curves display tolerably different shape owing to the properties of oils, and produce different amount of residual oils and irreducible water saturation.
Abstract: Flaring emissions during abnormal operating conditions such as plant start-ups, shut-downs, and upsets in chemical process industries (CPI) are usually significant. Flare minimization can help to save raw material and energy for CPI plants, and to improve local environmental sustainability. In this paper, a systematic methodology based on plant-wide dynamic simulation is presented for CPI plant flare minimizations under abnormal operating conditions. Since off-specification emission sources are inevitable during abnormal operating conditions, to significantly reduce flaring emission in a CPI plant, they must be either recycled to the upstream process for online reuse, or stored somewhere temporarily for future reprocessing, when the CPI plant manufacturing returns to stable operation. Thus, the off-spec products could be reused instead of being flared. This can be achieved through the identification of viable design and operational strategies during normal and abnormal operations through plant-wide dynamic scheduling, simulation, and optimization. The proposed study includes three stages of simulation works: (i) developing and validating a steady-state model of a CPI plant; (ii) transiting the obtained steady-state plant model to the dynamic modeling environment; and refining and validating the plant dynamic model; and (iii) developing flare minimization strategies for abnormal operating conditions of a CPI plant via a validated plant-wide dynamic model. This cost-effective methodology has two main merits: (i) employing large-scale dynamic modeling and simulations for industrial flare minimization, which involves various unit models for modeling hundreds of CPI plant facilities; (ii) dealing with critical abnormal operating conditions of CPI plants such as plant start-up and shut-down. Two virtual case studies on flare minimizations for start-up operation (over 50% of emission savings) and shut-down operation (over 70% of emission savings) of an ethylene plant have been employed to demonstrate the efficacy of the proposed study.
Abstract: The amount of the electrical power required by refrigeration systems is relevant worldwide. It is evaluated in the order of 15% of the total electricity production taking refrigeration and air-conditioning into consideration. For this reason, in the last years several energy saving techniques have been proposed to reduce the power demand of such plants. The paper deals with the development of an innovative internal recovery system for cryogenic cooling plants. Such a system consists in a Compressor-Expander Group (CEG) designed on the basis of the automotive turbocharging technology. In particular, the paper is focused on the design of the expander, the critical component of the CEG system. Due to the low volumetric flow entering the expander and the high expansion ratio, a commercial turbocharger expander wheel was strongly modified. It was equipped with a transonic nozzle, designed to have a radially inflow full admission. To verify the performance of such a machine and suggest improvements, two different set of nozzles have been designed and modelled by means of the commercial Ansys-CFX software. steady-state 3D CFD simulations of the second-generation prototype are presented and compared with the initial ones.
Abstract: An active islanding detection method using disturbance signal injection with intelligent controller is proposed in this study. First, a DC\AC power inverter is emulated in the distributed generator (DG) system to implement the tracking control of active power, reactive power outputs and the islanding detection. The proposed active islanding detection method is based on injecting a disturbance signal into the power inverter system through the d-axis current which leads to a frequency deviation at the terminal of the RLC load when the utility power is disconnected. Moreover, in order to improve the transient and steady-state responses of the active power and reactive power outputs of the power inverter, and to further improve the performance of the islanding detection method, two probabilistic fuzzy neural networks (PFNN) are adopted to replace the traditional proportional-integral (PI) controllers for the tracking control and the islanding detection. Furthermore, the network structure and the online learning algorithm of the PFNN are introduced in detail. Finally, the feasibility and effectiveness of the tracking control and the proposed active islanding detection method are verified with experimental results.
Abstract: In this paper, we present the use of the discriminant analysis to select evolutionary algorithms that better solve instances of the vehicle routing problem with time windows. We use indicators as independent variables to obtain the classification criteria, and the best algorithm from the generic genetic algorithm (GA), random search (RS), steady-state genetic algorithm (SSGA), and sexual genetic algorithm (SXGA) as the dependent variable for the classification. The discriminant classification was trained with classic instances of the vehicle routing problem with time windows obtained from the Solomon benchmark. We obtained a classification of the discriminant analysis of 66.7%.
Abstract: The effectiveness of microchannels in enhancing heat
transfer has been demonstrated in the semiconductor industry. In
order to tap the microscale heat transfer effects into macro
geometries, overcoming the cost and technological constraints,
microscale passages were created in macro geometries machined
using conventional fabrication methods. A cylindrical insert was
placed within a pipe, and geometrical profiles were created on the
outer surface of the insert to enhance heat transfer under steady-state
single-phase liquid flow conditions. However, while heat transfer
coefficient values of above 10 kW/m2·K were achieved, the heat
transfer enhancement was accompanied by undesirable pressure drop
increment. Therefore, this study aims to address the high pressure
drop issue using Constructal theory, a universal design law for both
animate and inanimate systems. Two designs based on Constructal theory were developed to study
the effectiveness of Constructal features in reducing the pressure drop
increment as compared to parallel channels, which are commonly
found in microchannel fabrication. The hydrodynamic and heat
transfer performance for the Tree insert and Constructal fin (Cfin)
insert were studied using experimental methods, and the underlying
mechanisms were substantiated by numerical results. In technical
terms, the objective is to achieve at least comparable increment in
both heat transfer coefficient and pressure drop, if not higher
increment in the former parameter. Results show that the Tree insert improved the heat transfer
performance by more than 16 percent at low flow rates, as compared
to the Tree-parallel insert. However, the heat transfer enhancement
reduced to less than 5 percent at high Reynolds numbers. On the
other hand, the pressure drop increment stayed almost constant at 20
percent. This suggests that the Tree insert has better heat transfer
performance in the low Reynolds number region. More importantly,
the Cfin insert displayed improved heat transfer performance along
with favourable hydrodynamic performance, as compared to Cfinparallel
insert, at all flow rates in this study. At 2 L/min, the
enhancement of heat transfer was more than 30 percent, with 20
percent pressure drop increment, as compared to Cfin-parallel insert.
Furthermore, comparable increment in both heat transfer coefficient
and pressure drop was observed at 8 L/min. In other words, the Cfin
insert successfully achieved the objective of this study. Analysis of the results suggests that bifurcation of flows is
effective in reducing the increment in pressure drop relative to heat
transfer enhancement. Optimising the geometries of the Constructal
fins is therefore the potential future study in achieving a bigger stride
in energy efficiency at much lower costs.
Abstract: This paper discusses the general methods to saturation
in the steady-state, two axis (d & q) frame models of synchronous
machines. In particular, the important role of the magnetic coupling
between the d-q axes (cross-magnetizing phenomenon), is
demonstrated. For that purpose, distinct methods of saturation
modeling of dumper synchronous machine with cross-saturation are
identified, and detailed models synthesis in d-q axes. A number of
models are given in the final developed form. The procedure and the
novel models are verified by a critical application to prove the
validity of the method and the equivalence between all developed
models is reported. Advantages of some of the models over the
existing ones and their applicability are discussed.
Abstract: This paper describes a new approach which can be
used to interpret the experimental creep deformation data obtained
from miniaturized thin plate bending specimen test to the
corresponding uniaxial data based on an inversed application of the
reference stress method. The geometry of the thin plate is fully
defined by the span of the support, l, the width, b, and the thickness,
d. Firstly, analytical solutions for the steady-state, load-line creep
deformation rate of the thin plates for a Norton’s power law under
plane stress (b→0) and plane strain (b→∞) conditions were obtained,
from which it can be seen that the load-line deformation rate of the
thin plate under plane-stress conditions is much higher than that
under the plane-strain conditions. Since analytical solution is not
available for the plates with random b-values, finite element (FE)
analyses are used to obtain the solutions. Based on the FE results
obtained for various b/l ratios and creep exponent, n, as well as the
analytical solutions under plane stress and plane strain conditions, an
approximate, numerical solutions for the deformation rate are
obtained by curve fitting. Using these solutions, a reference stress
method is utilised to establish the conversion relationships between
the applied load and the equivalent uniaxial stress and between the
creep deformations of thin plate and the equivalent uniaxial creep
strains. Finally, the accuracy of the empirical solution was assessed
by using a set of “theoretical” experimental data.
Abstract: In this work new macroporous Ni electrodes modified
with Au nanoparticles for hydrogen production have been developed.
The supporting macroporous Ni electrodes have been obtained by
means of the electrodeposition at high current densities. Then, the Au
nanoparticles were synthesized and added to the electrode surface.
The electrocatalytic behaviour of the developed electrocatalysts was
studied by means of pseudo-steady-state polarization curves,
electrochemical impedance spectroscopy (EIS) and hydrogen
discharge curves. The size of the Au synthetized nanoparticles shows
a monomodal distribution, with a very sharp band between 10 and 50
nm. The characteristic parameters d10, d50 and d90 were 14, 20 and
31 nm respectively. From Tafel polarization data has been concluded
that the Au nanoparticles improve the catalytic activity of the
developed electrodes towards the HER respect to the macroporous Ni
electrodes. EIS permits to obtain the electrochemically active area by
means of the roughness factor value. All the developed electrodes
show roughness factor values in the same order of magnitude. From
the activation energy results it can be concluded that the Au
nanoparticles improve the intrinsic catalytic activity of the
macroporous Ni electrodes.
Abstract: This paper reports the numerical simulation of doublediffusive
natural convection flows within a horizontal annular filled
with a saturated porous medium. The analysis concerns the influence
of the different parameters governing the problem, namely, the
Rayleigh number Ra, the Lewis number Le and the buoyancy ratio N,
on the heat and mass transfer and on the flow structure, in the case of
a fixed radius ratio R = 2. The numerical model used for the
discretization of the dimensionless equations governing the problem
is based on the finite difference method, using the ADI scheme. The
study is focused on steady-state solutions in the cooperation situation.
Abstract: The building sector is responsible, in many
industrialized countries, for about 40% of the total energy
requirements, so it seems necessary to devote some efforts in this
area in order to achieve a significant reduction of energy
consumption and of greenhouse gases emissions.
The paper presents a study aiming at providing a design
methodology able to identify the best configuration of the system
building/plant, from a technical, economic and environmentally point
of view.
Normally, the classical approach involves a building's energy
loads analysis under steady state conditions, and subsequent selection
of measures aimed at improving the energy performance, based on
previous experience made by architects and engineers in the design
team. Instead, the proposed approach uses a sequence of two wellknown
scientifically validated calculation methods (TRNSYS and
RETScreen), that allow quite a detailed feasibility analysis.
To assess the validity of the calculation model, an existing,
historical building in Central Italy, that will be the object of
restoration and preservative redevelopment, was selected as a casestudy.
The building is made of a basement and three floors, with a
total floor area of about 3,000 square meters.
The first step has been the determination of the heating and
cooling energy loads of the building in a dynamic regime by means,
which allows simulating the real energy needs of the building in
function of its use. Traditional methodologies, based as they are on
steady-state conditions, cannot faithfully reproduce the effects of
varying climatic conditions and of inertial properties of the structure.
With this model is possible to obtain quite accurate and reliable
results that allow identifying effective combinations building-HVAC
system.
The second step has consisted of using output data obtained as
input to the calculation model, which enables to compare different
system configurations from the energy, environmental and financial
point of view, with an analysis of investment, and operation and
maintenance costs, so allowing determining the economic benefit of
possible interventions.
The classical methodology often leads to the choice of
conventional plant systems, while our calculation model provides a
financial-economic assessment for innovative energy systems and
low environmental impact.
Computational analysis can help in the design phase, particularly
in the case of complex structures with centralized plant systems, by
comparing the data returned by the calculation model for different
design options.
Abstract: Experimental & numeral study of temperature
distribution during milling process, is important in milling quality
and tools life aspects. In the present study the milling cross-section
temperature is determined by using Artificial Neural Networks
(ANN) according to the temperature of certain points of the work
piece and the point specifications and the milling rotational speed of
the blade. In the present work, at first three-dimensional model of the
work piece is provided and then by using the Computational Heat
Transfer (CHT) simulations, temperature in different nods of the
work piece are specified in steady-state conditions. Results obtained
from CHT are used for training and testing the ANN approach. Using
reverse engineering and setting the desired x, y, z and the milling
rotational speed of the blade as input data to the network, the milling
surface temperature determined by neural network is presented as
output data. The desired points temperature for different milling
blade rotational speed are obtained experimentally and by
extrapolation method for the milling surface temperature is obtained
and a comparison is performed among the soft programming ANN,
CHT results and experimental data and it is observed that ANN soft
programming code can be used more efficiently to determine the
temperature in a milling process.
Abstract: A thermosyphon system is a heat transfer loop which
operates on the basis of gravity and buoyancy forces. It guarantees a
good reliability and low maintenance cost as it does not involve any
mechanical pump. Therefore, it can be used in many industrial
applications such as refrigeration and air conditioning, electronic
cooling, nuclear reactors, geothermal heat extraction, etc. But flow
instabilities and loop configuration are the major problems in this
system. Several previous researchers studied that stabilities can be
suppressed by using nanofluids as loop fluid. In the present study a
rectangular thermosyphon loop with end heat exchangers are
considered for the study. This configuration is more appropriate for
many practical applications such as solar water heater, geothermal
heat extraction, etc. In the present work, steady-state analysis is
carried out on thermosyphon loop with parallel flow coaxial heat
exchangers at heat source and heat sink. In this loop nanofluid is
considered as the loop fluid and water is considered as the external
fluid in both hot and cold heat exchangers. For this analysis onedimensional
homogeneous model is developed. In this model,
conservation equations like conservation of mass, momentum, energy
are discretized using finite difference method. A computer code is
written in MATLAB to simulate the flow in thermosyphon loop. A
comparison in terms of heat transfer is made between water and
nanofluid as working fluids in the loop.
Abstract: Economic Dispatch (ED) is one of the most
challenging problems of power system since it is difficult to determine
the optimum generation scheduling to meet the particular load demand
with the minimum fuel costs while all constraints are satisfied. The
objective of the Economic Dispatch Problems (EDPs) of electric
power generation is to schedule the committed generating units
outputs so as to meet the required load demand at minimum operating
cost while satisfying all units and system equality and inequality
constraints. In this paper, an efficient and practical steady-state genetic
algorithm (SSGAs) has been proposed for solving the economic
dispatch problem. The objective is to minimize the total generation
fuel cost and keep the power flows within the security limits. To
achieve that, the present work is developed to determine the optimal
location and size of capacitors in transmission power system where,
the Participation Factor Algorithm and the Steady State Genetic
Algorithm are proposed to select the best locations for the capacitors
and determine the optimal size for them.
Abstract: This paper proposes a complementary combination scheme of affine projection algorithm (APA) filters with different order of input regressors. A convex combination provides an interesting way to keep the advantage of APA having different order of input regressors. Consequently, a novel APA which has the rapid convergence and the reduced steady-state error is derived. Experimental results show the good properties of the proposed algorithm.
Abstract: This paper presents the use of phasor bond graphs to
obtain the steady-state behavior of a synchronous generator. The
phasor bond graph elements are built using 2D multibonds, which
represent the real and imaginary part of the phasor. The dynamic
bond graph model of a salient-pole synchronous generator is showed,
and verified viz. a sudden short-circuit test. The reduction of the
dynamic model into a phasor representation is described. The
previous test is executed on the phasor bond graph model, and its
steady-state values are compared with the dynamic response. Besides,
the widely used power (torque)-angle curves are obtained by means
of the phasor bond graph model, to test the usefulness of this model.
Abstract: This paper proposes a phasor representation of
electrical networks by using bond graph methodology. A so-called
phasor bond graph is built up by means of two-dimensional bonds,
which represent the complex plane. Impedances or admittances are
used instead of the standard bond graph elements. A procedure to
obtain the steady-state values from a phasor bond graph model is
presented. Besides the presentation of a phasor bond graph library in
SIDOPS code, also an application example is discussed.
Abstract: Anaerobic modeling is a useful tool to describe and
simulate the condition and behaviour of anaerobic treatment units for
better effluent quality and biogas generation. The present
investigation deals with the anaerobic treatment of brewery
wastewater with varying organic loads. The chemical oxygen demand
(COD) and total suspended solids (TSS) of the influent and effluent
of the bioreactor were determined at various retention times to
generate data for kinetic coefficients. The bio-kinetic coefficients in
the modified Stover–Kincannon kinetic and methane generation
models were determined to study the performance of anaerobic
digestion process. At steady-state, the determination of the kinetic
coefficient (K), the endogenous decay coefficient (Kd), the maximum
growth rate of microorganisms (μmax), the growth yield coefficient
(Y), ultimate methane yield (Bo), maximum utilization rate constant
Umax and the saturation constant (KB) in the model were calculated to
be 0.046 g/g COD, 0.083 (d¯¹), 0.117 (d-¹), 0.357 g/g, 0.516 (L
CH4/gCODadded), 18.51 (g/L/day) and 13.64 (g/L/day) respectively.
The outcome of this study will help in simulation of anaerobic model
to predict usable methane and good effluent quality during the
treatment of industrial wastewater. Thus, this will protect the
environment, conserve natural resources, saves time and reduce cost
incur by the industries for the discharge of untreated or partially
treated wastewater. It will also contribute to a sustainable long-term
clean development mechanism for the optimization of the methane
produced from anaerobic degradation of waste in a close system.
Abstract: In this paper, ANN controller for maximum power point tracking of photovoltaic (PV) systems is proposed and PV modeling is discussed. Maximum power point tracking (MPPT) methods are used to maximize the PV array output power by tracking continuously the maximum power point. ANN controller with hill-climbing algorithm offers fast and accurate converging to the maximum operating point during steady-state and varying weather conditions compared to conventional hill-climbing. The proposed algorithm gives a good maximum power operation of the PV system. Simulation results obtained are presented and compared with the conventional hill-climbing algorithm. Simulation results show the effectiveness of the proposed technique.
Abstract: In this paper, steady-state ampacity (current carrying capacity) evaluation of underground power cable system by using analytical and numerical methods for different conditions (depth of cable, spacing between phases, soil thermal resistivity, ambient temperature, wind speed), for two system voltage level were used 132 and 380 kV. The analytical method or traditional method that was used is based on the thermal analysis method developed by Neher-McGrath and further enhanced by International Electrotechnical Commission (IEC) and published in standard IEC 60287. The numerical method that was used is finite element method and it was recourse commercial software based on finite element method.