Abstract: Power systems are operating under stressed condition
due to continuous increase in demand of load. This can lead to
voltage instability problem when face additional load increase or
contingency. In order to avoid voltage instability suitable size of
reactive power compensation at optimal location in the system is
required which improves the load margin. This work aims at
obtaining optimal size as well as location of compensation in the 39-
bus New England system with the help of Bacteria Foraging and
Genetic algorithms. To reduce the computational time the work
identifies weak candidate buses in the system, and then picks only
two of them to take part in the optimization. The objective function is
based on a recently proposed voltage stability index which takes into
account the weighted average sensitivity index is a simpler and faster
approach than the conventional CPF algorithm. BFOA has been
found to give better results compared to GA.
Abstract: Vertical Handover(VHO) among different
communication technologies ensuring uninterruption and service
continuity is one of the most important performance parameter in
Heterogenous networks environment. In an integrated Universal
Mobile Telecommunicatin System(UMTS) and Wireless Local
Area Network(WLAN), WLAN is given an inherent priority over
UMTS because of its high data rates with low cost. Therefore
mobile users want to be associated with WLAN maximum of the
time while roaming, to enjoy best possible services with low cost.
That encourages reduction of number of VHO. In this work the
reduction of number of VHO with respect to varying number of
WLAN Access Points(APs) in an integrated UMTS and WLAN
network is investigated through simulation to provide best possible
cost effective service to the users. The simulation has been carried
out for an area (7800 × 9006)m2 where COST-231 Hata model
and 3GPP (TR 101 112 V 3.1.0) specified models are used for
WLAN and UMTS path loss models respectively. The handover
decision is triggered based on the received signal level as compared
to the fade margin. Fade margin gives a probabilistic measure of
the reliability of the communication link. A relationship between
number of WLAN APs and the number of VHO is also established
in this work.
Abstract: In this paper, the transient device performance analysis
of n-type Gate Inside JunctionLess Transistor (GI-JLT) has been
evaluated. 3-D Bohm Quantum Potential (BQP) transport device
simulation has been used to evaluate the delay and power dissipation
performance. GI-JLT has a number of desirable device parameters
such as reduced propagation delay, dynamic power dissipation,
power and delay product, intrinsic gate delay and energy delay
product as compared to Gate-all-around transistors GAA-JLT. In
addition to this, various other device performance parameters namely,
on/off current ratio, short channel effects (SCE), transconductance
Generation Factor (TGF) and unity gain cut-off frequency (fT ) and
subthreshold slope (SS) of the GI-JLT and GAA-JLT have been
analyzed and compared. GI-JLT shows better device performance
characteristics than GAA-JLT for low power and high frequency
applications, because of its larger gate electrostatic control on the
device operation.
Abstract: Several of the practical industrial control processes are
multivariable processes. Due to the relation amid the variables
(interaction), delay in the loops, it is very intricate to design a
controller directly for these processes. So first, the interaction of the
variables is analyzed using Relative Normalized Gain Array
(RNGA), which considers the time constant, static gain and delay
time of the processes. Based on the effect of RNGA, relative gain
array (RGA) and NI, the pair (control configuration) of variables to
be controlled by decentralized control is selected. The equivalent
transfer function (ETF) of the process model is estimated as first
order process with delay using the corresponding elements in the
Relative gain array and Relative average residence time array
(RARTA) of the processes. Secondly, a decentralized Proportional-
Integral (PI) controller is designed for each ETF simply using
frequency response specifications. Finally, the performance and
robustness of the algorithm is comparing with existing related
approaches to validate the effectiveness of the projected algorithm.
Abstract: Now-a-days autonomous mobile robots have found
applications in diverse fields. An autonomous robot system must be
able to behave in an intelligent manner to deal with complex and
changing environment. This work proposes the performance of path
planning and navigation of autonomous mobile robot using
Gravitational Search Algorithm (GSA), Simulated Annealing (SA)
and Particle Swarm optimization (PSO) based intelligent controllers
in an unstructured environment. The approach not only finds a valid
collision free path but also optimal one. The main aim of the work is
to minimize the length of the path and duration of travel from a
starting point to a target while moving in an unknown environment
with obstacles without collision. Finally, a comparison is made
between the three controllers, it is found that the path length and time
duration made by the robot using GSA is better than SA and PSO
based controllers for the same work.
Abstract: This paper proposes a backward/forward sweep
method to analyze the power flow in radial distribution systems. The
distribution system has radial structure and high R/X ratios. So the
newton-raphson and fast decoupled methods are failed with
distribution system. The proposed method presents a load flow study
using backward/forward sweep method, which is one of the most
effective methods for the load-flow analysis of the radial distribution
system. By using this method, power losses for each bus branch and
voltage magnitudes for each bus node are determined. This method
has been tested on IEEE 33-bus radial distribution system and
effective results are obtained using MATLAB.
Abstract: In this paper an isolated wind-diesel hybrid power
system has been considered for reactive power control study having
an induction generator for wind power conversion and synchronous
alternator with automatic voltage regulator (AVR) for diesel unit is
presented. The dynamic voltage stability evaluation is dependent on
small signal analysis considering a Static VAR Compensator (SVC)
and IEEE type -I excitation system. It's shown that the variable
reactive power source like SVC is crucial to meet the varying
demand of reactive power by induction generator and load and to
acquire an excellent voltage regulation of the system with minimum
fluctuations. Integral square error (ISE) criterion can be used to
evaluate the optimum setting of gain parameters. Finally the dynamic
responses of the power systems considered with optimum gain setting
will also be presented.
Abstract: This paper presents a hybrid fuzzy logic control
strategy for a unicycle trajectory following robot on irregular terrains.
In literature, researchers have presented the design of path tracking
controllers of mobile robots on non-frictional surface. In this work,
the robot is simulated to drive on irregular terrains with contrasting
frictional profiles of peat and rough gravel. A hybrid fuzzy logic
controller is utilised to stabilise and drive the robot precisely with the
predefined trajectory and overcome the frictional impact. The
controller gains and scaling factors were optimised using spiral
dynamics optimisation algorithm to minimise the mean square error
of the linear and angular velocities of the unicycle robot. The robot
was simulated on various frictional surfaces and terrains and the
controller was able to stabilise the robot with a superior performance
that is shown via simulation results.
Abstract: Ancillary services are support services which are
essential for humanizing and enhancing the reliability and security of
the electric power system. Reactive power ancillary service is one of
the important ancillary services in a restructured electricity market
which determines the cost of supplying ancillary services and finding
of how this cost would change with respect to operating decisions.
This paper presents a new formation that can be used to minimize the
Independent System Operator (ISO)’s total payment for reactive
power ancillary service. The modified power flow tracing algorithm
estimates the availability of reserve reactive power for ancillary
service. In order to find optimum reactive power dispatch,
Biogeography based optimization method (BPO) is proposed. Market
Reactive Clearing Price (MRCP) is then estimated and it encourages
generator companies (GENCOs) to participate in an ancillary service.
Finally, optimal weighting factor and real time utilization factor of
reactive power give the minimum ISO’s total payment. The
effectiveness of proposed design is verified using IEEE 30 bus
system.
Abstract: Spectrum sensing is the main feature of cognitive
radio technology. Spectrum sensing gives an idea of detecting the
presence of the primary users in a licensed spectrum. In this paper we
compare the theoretical results of detection probability of different
fading environments like Rayleigh, Rician, Nakagami-m fading
channels with the simulation results using energy detection based
spectrum sensing. The numerical results are plotted as Pf Vs Pd for
different SNR values, fading parameters. It is observed that
Nakagami fading channel performance is better than other fading
channels by using energy detection in spectrum sensing. A MATLAB
simulation test bench has been implemented to know the performance
of energy detection in different fading channel environment.
Abstract: Anultra-low power capacitor less low-dropout voltage
regulator with improved transient response using gain enhanced feed
forward path compensation is presented in this paper. It is based on a
cascade of a voltage amplifier and a transconductor stage in the feed
forward path with regular error amplifier to form a composite gainenhanced
feed forward stage. It broadens the gain bandwidth and thus
improves the transient response without substantial increase in power
consumption. The proposed LDO, designed for a maximum output
current of 100 mA in UMC 180 nm, requires a quiescent current of
69 )A. An undershot of 153.79mV for a load current changes from
0mA to 100mA and an overshoot of 196.24mV for current change of
100mA to 0mA. The settling time is approximately 1.1 )s for the
output voltage undershooting case. The load regulation is of 2.77
)V/mA at load current of 100mA. Reference voltage is generated by
using an accurate band gap reference circuit of 0.8V.The costly
features of SOC such as total chip area and power consumption is
drastically reduced by the use of only a total compensation
capacitance of 6pF while consuming power consumption of 0.096
mW.
Abstract: Two types of commercial cylindrical lithium ion
batteries (Panasonic 3.4 Ah NCR-18650B and Samsung 2.9 Ah
INR-18650), were investigated experimentally. The capacities of these
samples were individually measured using constant current-constant
voltage (CC-CV) method at different ambient temperatures (-10°C,
0°C, 25°C). Their internal resistance was determined by
electrochemical impedance spectroscopy (EIS) and pulse discharge
methods. The cells with different configurations of parallel connection
NCR-NCR, INR-INR and NCR-INR were charged/discharged at the
aforementioned ambient temperatures. The results showed that the
difference of internal resistance between cells much more evident at
low temperatures. Furthermore, the parallel connection of NCR-NCR
exhibits the most uniform temperature distribution in cells at -10°C,
this feature is quite favorable for the safety of the battery pack.
Abstract: Among all FACTS devices, the unified power flow
controller (UPFC) is considered to be the most versatile device.
This is due to its capability to control all the transmission system
parameters (impedance, voltage magnitude, and phase angle). With
the growing interest in UPFC, the attention to develop a mathematical
model has increased. Several models were introduced for UPFC in
literature for different type of studies in power systems. In this paper
a novel comparison study between two dynamic models of UPFC
with their proposed control strategies.
Abstract: Researches and concerns in power quality gained
significant momentum in the field of power electronics systems over
the last two decades globally. This sudden increase in the number of
concerns over power quality problems is a result of the huge increase
in the use of non-linear loads. In this paper, power quality evaluation
of some distribution networks at Misurata - Libya has been done
using a power quality and energy analyzer (Fluke 437 Series II). The
results of this evaluation are used to minimize the problems of power
quality. The analysis shows the main power quality problems that
exist and the level of awareness of power quality issues with the aim
of generating a start point which can be used as guidelines for
researchers and end users in the field of power systems.
Abstract: Lightning protection systems (LPS) for wind power
generation is becoming an important public issue. A serious damage
of blades, accidents where low-voltage and control circuit
breakdowns are frequently occur in many wind farms. A grounding
system is one of the most important components required for
appropriate LPSs in wind turbines WTs. Proper design of a wind
turbine grounding system is demanding and several factors for the
proper and effective implementation must taken into account. In this
paper proposed procedure of proper design of grounding systems for
a wind turbine was introduced. This procedure depends on measuring
of ground current of simulated wind farm under lightning taking into
consideration the soil ionization. The procedure also includes the
Ground Potential Rise (GPR) and the voltage distributions at ground
surface level and Touch potential. In particular, the contribution of
mitigating techniques, such as rings, rods and the proposed design
were investigated.
Abstract: This paper presents the design and analysis of Liquid
Crystal (LC) based tunable reflectarray antenna with different design
configurations within X-band frequency range. The effect of LC
volume used for unit cell element on frequency tunability and
reflection loss performance has been investigated. Moreover different
slot embedded patch element configurations have been proposed for
LC based tunable reflectarray antenna design with enhanced
performance. The detailed fabrication and measurement procedure
for different LC based unit cells has been presented. The waveguide
scattering parameter measured results demonstrated that by using the
circular slot embedded patch elements, the frequency tunability and
dynamic phase range can be increased from 180MHz to 200MHz and
120° to 124° respectively. Furthermore the circular slot embedded
patch element can be designed at 10GHz resonant frequency with a
patch volume of 2.71mm3 as compared to 3.47mm3 required for
rectangular patch without slot.
Abstract: In order to evaluate the performance of a unified power
flow controller (UPFC), mathematical models for steady state and
dynamic analysis are to be developed. The steady state model is
mainly concerned with the incorporation of the UPFC in load flow
studies. Several load flow models for UPFC have been introduced
in literature, and one of the most reliable models is the decoupled
UPFC model. In spite of UPFC decoupled load flow model simplicity,
it is more robust compared to other UPFC load flow models and it
contains unique capabilities. Some shortcoming such as additional
set of nonlinear equations are to be solved separately after the load
flow solution is obtained. The aim of this study is to investigate the
different control strategies that can be realized in the decoupled load
flow model (individual control and combined control), and the impact
of the location of the UPFC in the network on its control parameters.
Abstract: The high Peak to Average Power Ratio (PAR) in Filter
Bank Multicarrier with Offset Quadrature Amplitude Modulation
(FBMC-OQAM) can significantly reduce power efficiency and
performance. In this paper, we address the problem of PAPR
reduction for FBMC-OQAM systems using Tone Reservation (TR)
technique. Due to the overlapping structure of FBMCOQAM signals,
directly applying TR schemes of OFDM systems to FBMC-OQAM
systems is not effective. We improve the tone reservation (TR)
technique by employing sliding window with Active Constellation
Extension for the PAPR reduction of FBMC-OQAM signals, called
sliding window tone reservation Active Constellation Extension
(SW-TRACE) technique. The proposed SW-TRACE technique uses
the peak reduction tones (PRTs) of several consecutive data
blocks to cancel the peaks of the FBMC-OQAM signal inside a
window, with dynamically extending outer constellation points in
active(data-carrying) channels, within margin-preserving constraints,
in order to minimize the peak magnitude. Analysis and simulation
results compared to the existing Tone Reservation (TR) technique for
FBMC/OQAM system. The proposed method SW-TRACE has better
PAPR performance and lower computational complexity.
Abstract: This paper presents the design and analysis of Liquid
Crystal (LC) based tunable reflectarray antenna with different design
configurations within X-band frequency range. The effect of LC
volume used for unit cell element on frequency tunability and
reflection loss performance has been investigated. Moreover different
slot embedded patch element configurations have been proposed for
LC based tunable reflectarray antenna design with enhanced
performance. The detailed fabrication and measurement procedure
for different LC based unit cells has been presented. The waveguide
scattering parameter measured results demonstrated that by using the
circular slot embedded patch elements, the frequency tunability and
dynamic phase range can be increased from 180MHz to 200MHz and
120° to 124° respectively. Furthermore the circular slot embedded
patch element can be designed at 10GHz resonant frequency with a
patch volume of 2.71mm3 as compared to 3.47mm3 required for
rectangular patch without slot.
Abstract: In this paper an extensive verification of the extraction
method (published earlier) that consistently accounts for self-heating
and Early effect to accurately extract both base and thermal resistance
of bipolar junction transistors is presented. The method verification is
demonstrated on advanced RF SiGe HBTs were the extracted results
for the thermal resistance are compared with those from another
published method that ignores the effect of Early effect on internal
base-emitter voltage and the extracted results of the base resistance
are compared with those determined from noise measurements. A
self-consistency of our method in the extracted base resistance and
thermal resistance using compact model simulation results is also
carried out in order to study the level of accuracy of the method.