Abstract: The traditional second order statistics approach of using only the hermitian covariance for non circular signals, does not take advantage of the information contained in the complementary covariance of these signals. Radar systems often use non circular signals such as Binary Phase Shift Keying (BPSK) signals. Their noncicular property can be exploited together with the dual centrosymmetry of the bistatic MIMO radar system to improve angle estimation performance. We construct an augmented matrix from the received data vectors using both the positive definite hermitian covariance matrix and the complementary covariance matrix. The Unitary ESPRIT technique is then applied to the signal subspace of the augmented covariance matrix for automatically paired Direction-of-arrival (DOA) and Direction-of-Departure (DOD) angle estimates. The number of targets that can be detected is twice that obtainable with the conventional ESPRIT approach. Simulation results show the effectiveness of this method in terms of increase in resolution and the number of targets that can be detected.
Abstract: A vertical SOI-based MOSFET with trench body
structure operated as 1T DRAM cell at various temperatures has been
studied and investigated. Different operation temperatures are
assigned for the device for its performance comparison, thus the
thermal stability is carefully evaluated for the future memory device
applications. Based on the simulation, the vertical SOI-based
MOSFET with trench body structure demonstrates the electrical
characteristics properly and possess conspicuous kink effect at
various operation temperatures. Transient characteristics were also
performed to prove that its programming window values and
retention time behaviors are acceptable when the new 1T DRAM cell
is operated at high operation temperature.
Abstract: Headphones and earphones have many extremely small
holes or narrow slits; they use sound-absorbing or porous material (i.e.,
dampers) to suppress vibratory system resonance. The air viscosity in
these acoustic paths greatly affects the acoustic properties. Simulation
analyses such as the finite element method (FEM) therefore require
knowledge of the material properties of sound-absorbing or porous
materials, such as the characteristic impedance and propagation
constant. The transfer function method using acoustic tubes is a widely
known measuring method, but there is no literature on taking
measurements up to the audible range. To measure the acoustic
properties at high-range frequencies, the acoustic tubes that form the
measuring device need to be narrowed, and the distance between the
two microphones needs to be reduced. However, when the tubes are
narrowed, the characteristic impedance drops below the air impedance.
In this study, we considered the effect of air viscosity in an acoustical
tube, introduced a theoretical formula for this effect in the form of
complex density and complex sonic velocity, and verified the
theoretical formula. We also conducted an experiment and observed
the effect from air viscosity in the actual measurements.
Abstract: Detection and classification of power quality (PQ)
disturbances is an important consideration to electrical utilities and
many industrial customers so that diagnosis and mitigation of such
disturbance can be implemented quickly. S-transform algorithm and
continuous wavelet transforms (CWT) are time-frequency
algorithms, and both of them are powerful in detection and
classification of PQ disturbances. This paper presents detection and
classification of PQ disturbances using S-transform and CWT
algorithms. The results of detection and classification, provides that
S-transform is more accurate in detection and classification for most
PQ disturbance than CWT algorithm, where as CWT algorithm more
powerful in detection in some disturbances like notching
Abstract: This paper presents the hardware design of a unified
architecture to compute the 4x4, 8x8 and 16x16 efficient twodimensional
(2-D) transform for the HEVC standard. This
architecture is based on fast integer transform algorithms. It is
designed only with adders and shifts in order to reduce the hardware
cost significantly. The goal is to ensure the maximum circuit reuse
during the computing while saving 40% for the number of operations.
The architecture is developed using FIFOs to compute the second
dimension. The proposed hardware was implemented in VHDL. The
VHDL RTL code works at 240 MHZ in an Altera Stratix III FPGA.
The number of cycles in this architecture varies from 33 in 4-point-
2D-DCT to 172 when the 16-point-2D-DCT is computed. Results
show frequency improvements reaching 96% when compared to an
architecture described as the direct transcription of the algorithm.
Abstract: This paper shows how we can integrate
communication modeling into the design modeling at early stages of
the design flow. We consider effect of incorporating noise such as
impulsive noise on system stability. We show that with change of the
system model and investigate the system performance under the
different communication effects. We modeled a unmanned aerial
vehicle (UAV) as a demonstration using SystemC methodology.
Moreover the system is modeled by joining the capabilities of UML
and SystemC to operate at system level.
Abstract: This paper presents the modeling and simulation of a hybrid proton exchange membrane fuel cell (PEMFC) with an energy storage system for use in a stand-alone distributed generation (DG) system. The simulation model consists of fuel cell DG, lead-acid battery, maximum power point tracking and power conditioning unit which is modeled in the MATLAB/Simulink platform. Poor loadfollowing characteristics and slow response to rapid load changes are some of the weaknesses of PEMFC because of the gas processing reaction and the fuel cell dynamics. To address the load-tracking issues in PEMFC, a hybrid PEMFC and battery storage system is considered and modelled. The model utilizes PEMFC as the main energy source whereas the battery functions as energy storage to compensate for the limitations of PEMFC.Simulation results are given to show the overall system performance under light and heavyloading conditions.
Abstract: This paper presents a new methodology to study power and energy consumption in mechatronic systems early in the development process. This new approach makes use of two modeling languages to represent and simulate embedded control software and electromechanical subsystems in the discrete event and continuous time domain respectively within a single co-model. This co-model enables an accurate representation of power and energy consumption and facilitates the analysis and development of both software and electro-mechanical subsystems in parallel. This makes the engineers aware of energy-wise implications of different design alternatives and enables early trade-off analysis from the beginning of the analysis and design activities.
Abstract: In the hardening energy context, the transport sector
which constitutes a large worldwide energy demand has to be
improving for decrease energy demand and global warming impacts.
In a controversial situation where subsists an increasing demand for
long-distance and high-speed travels, high-speed trains offer many
advantages, as consuming significantly less energy than road or air
transports.
At the project phase of new rail infrastructures, it is nowadays
important to characterize accurately the energy that will be induced
by its operation phase, in addition to other more classical criteria as
construction costs and travel time.
Current literature consumption models used to estimate railways
operation phase are obsolete or not enough accurate for taking into
account the newest train or railways technologies.
In this paper, an updated model of consumption for high-speed is
proposed, based on experimental data obtained from full-scale tests
performed on a new high-speed line. The assessment of the model
is achieved by identifying train parameters and measured power
consumptions for more than one hundred train routes. Perspectives
are then discussed to use this updated model for accurately assess
the energy impact of future railway infrastructures.
Abstract: In contrast to conventional generators, self-excited induction generators are found to be most suitable machines for wind energy conversion in remote and windy areas due to many advantages over grid connected machines. This papers presents a Self-Excited Induction Generator (SEIG) driven by wind turbine and supplying an induction motor which is coupled to a centrifugal pump. A method to describe the steady state performance based on nodal analysis is presented. Therefore the advanced knowledge of the minimum excitation capacitor value is required. The effects of variation of excitation capacitance on system and rotor speed under different loading conditions have been analyzed and considered to optimize induction motor pump performances.
Abstract: Pineapples can be classified using an index with seven
levels of maturity based on the green and yellow color of the skin. As
the pineapple ripens, the skin will change from pale green to a golden
or yellowish color. The issues that occur in agriculture nowadays are
to do with farmers being unable to distinguish between the indexes of
pineapple maturity correctly and effectively. There are several
reasons for why farmers cannot properly follow the guideline provide
by Federal Agriculture Marketing Authority (FAMA) and one of
reason is that due to manual inspection done by experts, there are no
specific and universal guidelines to be adopted by farmers due to the
different points of view of the experts when sorting the pineapples
based on their knowledge and experience. Therefore, an automatic
system will help farmers to identify pineapple maturity effectively
and will become a universal indicator to farmers.
Abstract: Power Factor (PF) is one of the most important parameters in the electrical systems, especially in the water pumping station. The low power factor value of the water pumping stations causes penalty for the electrical bill. There are many methods use for power factor improvement. Each one of them uses a capacitor on the electrical power network. The position of the capacitors is varied depends on many factors such as; voltage level and capacitors rating. Adding capacitors on the motor terminals increase the supply power factor from 0.8 to more than 0.9 but these capacitors cause some problems for the electrical grid network, such as increasing the harmonic contents of the grid line voltage. In this paper the effects of using capacitors in the water pumping stations to improve the power factor value on the harmonic contents of the electrical grid network are studied. One of large water pumping stations in Kafr El-Shikh Governorate in Egypt was used, as a case study. The effect of capacitors on the line voltage harmonic contents is measured. The station uses capacitors to improve the PF values at the 1 lkv grid network. The power supply harmonics values are measured by a power quality analyzer at different loading conditions. The results showed that; the capacitors improved the power factor value of the feeder and its value increased than 0.9. But the THD values are increased by adding these capacitors. The harmonic analysis showed that; the 13th, 17th, and 19th harmonics orders are increased also by adding the capacitors.
Abstract: This paper presents a speed fuzzy sliding mode
controller for a vector controlled induction machine (IM) fed by a
voltage source inverter (PWM).
The sliding mode based fuzzy control method is developed to
achieve fast response, a best disturbance rejection and to maintain a
good decoupling.
The problem with sliding mode control is that there is high
frequency switching around the sliding mode surface. The FSMC is
the combination of the robustness of Sliding Mode Control (SMC)
and the smoothness of Fuzzy Logic (FL). To reduce the torque
fluctuations (chattering), the sign function used in the conventional
SMC is substituted with a fuzzy logic algorithm.
The proposed algorithm was simulated by Matlab/Simulink
software and simulation results show that the performance of the
control scheme is robust and the chattering problem is solved.
Abstract: The purpose of this research is to develop and apply the
RSCMAC to enhance the dynamic accuracy of Global Positioning
System (GPS). GPS devices provide services of accurate positioning,
speed detection and highly precise time standard for over 98% area on
the earth. The overall operation of Global Positioning System includes
24 GPS satellites in space; signal transmission that includes 2
frequency carrier waves (Link 1 and Link 2) and 2 sets random
telegraphic codes (C/A code and P code), on-earth monitoring stations
or client GPS receivers. Only 4 satellites utilization, the client position
and its elevation can be detected rapidly. The more receivable
satellites, the more accurate position can be decoded. Currently, the
standard positioning accuracy of the simplified GPS receiver is greatly
increased, but due to affected by the error of satellite clock, the
troposphere delay and the ionosphere delay, current measurement
accuracy is in the level of 5~15m. In increasing the dynamic GPS
positioning accuracy, most researchers mainly use inertial navigation
system (INS) and installation of other sensors or maps for the
assistance. This research utilizes the RSCMAC advantages of fast
learning, learning convergence assurance, solving capability of
time-related dynamic system problems with the static positioning
calibration structure to improve and increase the GPS dynamic
accuracy. The increasing of GPS dynamic positioning accuracy can be
achieved by using RSCMAC system with GPS receivers collecting
dynamic error data for the error prediction and follows by using the
predicted error to correct the GPS dynamic positioning data. The
ultimate purpose of this research is to improve the dynamic positioning
error of cheap GPS receivers and the economic benefits will be
enhanced while the accuracy is increased.
Abstract: This paper presents modeling and analysis of 12-phase distribution static compensator (DSTATCOM), which is capable of balancing the source currents in spite of unbalanced loading and phase outages. In addition to balance the supply current, the power factor can be set to a desired value. The theory of instantaneous symmetrical components is used to generate the twelve-phase reference currents. These reference currents are then tracked using current controlled voltage source inverter, operated in a hysteresis band control scheme. An ideal compensator in place of physical realization of the compensator is used. The performance of the proposed DTATCOM is validated through MATLAB simulation and detailed simulation results are given.
Abstract: In this paper, the gain spectrum of EDFA has been broadened by implementing HTE configuration for S and C band. On using this configuration an amplification bandwidth of 76nm ranging from 1479nm to 1555nm with a peak gain of 26dB has been obtained.
Abstract: This paper deals with stakeholders’ decisions within energy neutral urban redevelopment processes. The decisions of these stakeholders during the process will make or break energy neutral ambitions. An extensive form of game theory model gave insight in the behavioral differences of stakeholders regarding energy neutral ambitions and the effects of the changing legislation. The results show that new legislation regarding spatial planning slightly influences the behavior of stakeholders. An active behavior of the municipality will still result in the best outcome. Nevertheless, the municipality becomes more powerful when acting passively and can make the use of planning tools to provide governance towards energy neutral urban redevelopment. Moreover, organizational support, recognizing the necessity for energy neutrality, keeping focused and collaboration among stakeholders are crucial elements to achieve the objective of an energy neutral urban (re)development.
Abstract: As known, the guard wires of overhead high voltage
are usually grounded through the grounding systems of support and
of the terminal stations. They do affect the zero sequence impedance
value of the line, Z0, which is generally, calculated assuming that the
wires guard are at ground potential. In this way it is not considered
the effect of the resistances of earth of supports and stations. In this
work is formed a formula for the calculation of Z0 which takes
account of said resistances. Is also proposed a method of calculating
the impedance zero sequence overhead lines in which, in various
sections or spans, the guard wires are connected to the supports, or
isolated from them, or are absent. Parametric analysis is given for
lines 220 kV and 400 kV, which shows the extent of the errors made
with traditional methods of calculation.
Abstract: For the past couple of decades Weak signal detection
is of crucial importance in various engineering and scientific
applications. It finds its application in areas like Wireless
communication, Radars, Aerospace engineering, Control systems and
many of those. Usually weak signal detection requires phase sensitive
detector and demodulation module to detect and analyze the signal.
This article gives you a preamble to intrusion detection system which
can effectively detect a weak signal from a multiplexed signal. By
carefully inspecting and analyzing the respective signal, this
system can successfully indicate any peripheral intrusion. Intrusion
detection system (IDS) is a comprehensive and easy approach
towards detecting and analyzing any signal that is weakened and
garbled due to low signal to noise ratio (SNR). This approach
finds significant importance in applications like peripheral security
systems.
Abstract: Photovoltaic power generation forecasting is an
important task in renewable energy power system planning and
operating. This paper explores the application of neural networks
(NN) to study the design of photovoltaic power generation
forecasting systems for one week ahead using weather databases
include the global irradiance, and temperature of Ghardaia city
(south of Algeria) using a data acquisition system. Simulations were
run and the results are discussed showing that neural networks
Technique is capable to decrease the photovoltaic power generation
forecasting error.