Two and Three Layer Lamination of Nanofiber

For their exceptional properties nanofibers, respectively, nanofiber layers are achieving an increasingly wider range of uses. Nowadays nanofibers are used mainly in the field of air filtration where they are removing submicron particles, bacteria, and viruses. Their efficiency is not changed in time, and the power consumption is much lower than that of electrically charged filters. Nanofibers are primarily used for converting and storage of energy in both air and liquid filtration, in food and packaging, protecting the environment, but also in health care which is made possible by their newly discovered properties. However, a major problem of the nanofiber layer is practically zero abrasion resistance; it is, therefore, necessary to laminate the nanofiber layer with another suitable material. Unfortunately, lamination of nanofiber layers is a major problem since the nanofiber layer contains small pores through which it is very difficult for adhesion to pass through. Therefore, there is still only a small percentage of products with these unique fibers 5.





References:
[1] TUL: Method of production of nanofibres from the polymer solution by electrostatic spinning and equipment to perform the way CZ Patent 294,274, 2003-2421, 2013.
[2] O. Jirsak, F. Sanetrnik, D. Lukas, V. Kotek, L. Martinova, J. Chaloupek, A Method of Nanofibres Production from a Polymer Solution Using Electrostatic Spinning and a Device for Carrying Out the Method. EP 1673493, 2006.
[3] L. Hes, P. Sluka, Introduction to the comfort of textiles, Technical University of Liberec, 2005.
[4] T. Heinish, V. Bajzik. , R. Knizek, Effect of the process of lamination microporous nanofiber membrane on the evaporative resistance of the two-layer laminate, Advanced Materials Research, 677, 103-108, ISSN: 10226680, 2013.
[5] P. W. Gibson, Factors Influencing Steady-State Heat and Water Vapor Transfer Measurements for Clothing Materials, Textile Research Journal, Vol. 63 no. 12, 749-764, 1993.
[6] P. Gunavathi, Characterization of nanomembrane using nylon/6 and nylon/6 polye (e- caprolactine) blend, Indian Journal of Fibre &Textile Research, 201-306, 2012.
[7] D. Reneker, I. Chun, Nanometre diameter fibres of polymer, produced by electrospinning, Nanotechnology, 7, 215, 1996.
[8] R. Knizek. L. Fridrichova, V. Bajzik, Polyurethane coating on a supporting layer of polymeric nanofibers, Advanced Materials Research, 607, 31-35, ISSN: 10226680, 2013.
[9] J. A. Prince, D. Rana, T. Matsuura, N. Ayyanar, T. S. Shanmugasundaram, G. Singh, Nanofiber based triple layer hydro-philic/-phobic membrane - a solution for pore wetting in membrane distillation, Scientific Reports, 4, 6949, 2014.
[10] C. J. Luo, Simeon D. Stoyanov, E. Stride, E. Pelanb, M. Edirisinghe, Electrospinning versus fibre production methods: from specifics to technological convergence, Chemical Society Reciews, 41, 4708-4735, 2012.
[11] P. Gibson, H. Schreuder-Gibson, D. Rivin, Transport properties of porous membranes based on electrospun nanofibers, Colloids and Surfaces A: Physicochemical and Engineering Aspects, Vol. 187–188, 469–481, 2001.
[12] Hohenstein Institute, Clothing physiological research in the service of wear comfort, H.I. Germany, Editor. 2009.
[13] L. Hes, Fundaments of design of fabrics and garments with demanded thermophysiological comfort, International Round Table, Clothing Comfort – Condition of Life Quality, 2009.
[14] J. E. Ruckman, R. Murray,H. S. Choi, Engineering of clothing systems for improved thermophysiological comfort:The effect of openings. International Journal of Clothing Science and Technology,37-52, 1999.
[15] F. Kar,J. Fan, W. Yu, X. Wan, Effects of thermal and moisture trasnprt properties of T-Shirton wearers comfort sensations. Fibers and and Polymers, Vol. 8, Number 5, 2007.