Fully Printed Strain Gauges: A Comparison of Aerosoljet-Printing and Micropipette-Dispensing

Strain sensors based on a change in resistance are
well established for the measurement of forces, stresses, or material
fatigue. Within the scope of this paper, fully additive manufactured
strain sensors were produced using an ink of silver nanoparticles.
Their behavior was evaluated by periodic tensile tests. Printed
strain sensors exhibit two advantages: Their measuring grid is
adaptable to the use case and they do not need a carrier-foil,
as the measuring structure can be printed directly onto a thin
sprayed varnish layer on the aluminum specimen. In order to
compare quality characteristics, the sensors have been manufactured
using two different technologies, namely aerosoljet-printing and
micropipette-dispensing. Both processes produce structures which
exhibit continuous features (in contrast to what can be achieved with
droplets during inkjet printing). Briefly summarized the results show
that aerosoljet-printing is the preferable technology for specimen with
non-planar surfaces whereas both technologies are suitable for flat
specimen.




References:
[1] A. M. Allanurov and A. Ye. Zdrok and A. G. Loschilov and
N. D. Malyutin Problem of ink evaporation while using plotter systems to
manufacture printed electronic products, Procedia Technology, Vol. 18,
Pages 19–24, Elsevier, 2014.
[2] Norm DIN 50125 Testing of metallic materials - Tensile test pieces,
December 2016, Deutsches Institut fuer Normung e.V., Beuth Verlag.
[3] F. L. Hammond and M. J. Smith and R. J. Wood Estimating surgical
needle deflection with printed strain gauges, Engineering in Medicine and
Biology Society (EMBC), 2014 36th Annual International Conference of
the IEEE, Vol. 54, No. 2, Pages 6931–6936, IEEE, 2014.
[4] O. Kravchuk and M. Reichenberger Properties and long-term behavior
of nanoparticle based inkjet printed strain gauges, Journal of Materials
Science: Materials in Electronics, Vol. 27, No. 10, Pages 10934–10940,
Springer, 2016.
[5] B. J. Larson and S. D. Gillmor and M. G. Lagally Controlled deposition
of picoliter amounts of fluid using an ultrasonically driven micropipette,
Review of Scientific Instruments, Vol. 75, No. 4, Pages 832–836, AIP,
2004.
[6] M. Maiwald and C. Werner and V. Zoellmer and M. Busse INKtelligent
printed strain gauges, Sensors and Actuators A: Physical, Vol. 162, No.
2, Pages 198–201, Elsevier, 2010.
[7] B. Polzinger and J. Keck and V. Matic and W. Eberhardt Inkjet and
Aerosol Jet Printed Sensors on 2D and 3D Substrates, Proceedings of
the AMA Conferences, 2015.
[8] T. Seifert and E. Sowade and F. Roscher and M. Wiemer and Th. Gessner
and R. R. Baumann Additive manufacturing technologies compared:
morphology of deposits of silver ink using inkjet and aerosol jet printing,
Industrial & Engineering Chemistry Research, Vol. 54, No. 2, Pages
769–779, ACS Publications, 2015.
[9] M. Smith and Y. S. Choi and C. Boughey and S. Kar-Narayan Controlling
and assessing the quality of aerosol jet printed features for large area
and flexible electronics, Flexible and Printed Electronics, Vol. 2, No. 1,
IOP Publishing, 2017.
[10] V. Zoellmer, and E. P´al and M. Maiwald and Ch. Werner and
D. Godlinski and D. Lehmhus and I. Wirth and M. Busse Functional
materials for printed sensor structures, Proceedings of the 1st Joint
International Symposium on System-Integrated Intelligence, No. 1, 2012.