Abstract: A self-evolution algorithm for optimizing neural networks using a combination of PSO and JPSO is proposed. The algorithm optimizes both the network topology and parameters simultaneously with the aim of achieving desired accuracy with less complicated networks. The performance of the proposed approach is compared with conventional back-propagation networks using several synthetic functions, with better results in the case of the former. The proposed algorithm is also implemented on slope stability problem to estimate the critical factor of safety. Based on the results obtained, the proposed self evolving network produced a better estimate of critical safety factor in comparison to conventional BPN network.
Abstract: In recent years, rehabilitation has been the subject of extensive research due to increased spending on building work and repair of built works. In all cases, it is absolutely essential to carry out methods of strengthening or repair of structural elements, and that following an inspection analysis and methodology of a correct diagnosis. The reinforced concrete columns are important elements in building structures. They support the vertical loads and provide bracing against the horizontal loads. This research about the behavior of reinforced concrete rectangular columns, rehabilitated by concrete liner, confinement FRP fabric, steel liner or cage formed by metal corners. It allows comparing the contributions of different processes used perspective section resistance elements rehabilitated compared to that is not reinforced or repaired. The different results obtained revealed a considerable gain in bearing capacity failure of reinforced sections cladding concrete, metal bracket, steel plates and a slight improvement to the section reinforced with fabric FRP. The use of FRP does not affect the weight of the structures, but the use of different techniques cladding increases the weight of elements rehabilitated and therefore the weight of the building which requires resizing foundations.
Abstract: This paper characterizes the effects of artificial short
term aging in the laboratory on the rheological properties of virgin
80/100 penetration grade asphalt binder. After several years in
service, asphalt mixture started to deteriorate due to aging. Aging is a
complex physico-chemical phenomenon that influences asphalt
binder rheological properties causing a deterioration in asphalt
mixture performance. To ascertain asphalt binder aging effects, the
virgin, artificially aged and extracted asphalt binder were tested via
the Rolling Thin film Oven (RTFO), Dynamic Shear Rheometer
(DSR) and Rotational Viscometer (RV). A comparative study
between laboratory and field aging conditions were also carried out.
The results showed that the specimens conditioned for 85 minutes
inside the RTFO was insufficient to simulate the actual short term
aging caused that took place in the field under Malaysian field
conditions
Abstract: Imperfect knowledge cannot be avoided all the time. Imperfections may have several forms; uncertainties, imprecision and incompleteness. When we look to classification of methods for the management of imperfect knowledge we see fuzzy set-based techniques. The choice of a method to process data is linked to the choice of knowledge representation, which can be numerical, symbolic, logical or semantic and it depends on the nature of the problem to be solved for example decision support, which will be mentioned in our study. Fuzzy Logic is used for its ability to manage imprecise knowledge, but it can take advantage of the ability of neural networks to learn coefficients or functions. Such an association of methods is typical of so-called soft computing. In this study a new method was used for the management of imprecision for collected knowledge which related to economic analysis of construction industry in Turkey. Because of sudden changes occurring in economic factors decrease competition strength of construction companies. The better evaluation of these changes in economical factors in view of construction industry will made positive influence on company-s decisions which are dealing construction.
Abstract: In the present paper, a set of parametric FE stress
analyses is carried out for two-planar welded tubular DKT-joints
under two different axial load cases. Analysis results are used to
present general remarks on the effect of geometrical parameters on
the stress concentration factors (SCFs) at the inner saddle, outer
saddle, toe, and heel positions on the main (outer) brace. Then a new
set of SCF parametric equations is developed through nonlinear
regression analysis for the fatigue design of two-planar DKT-joints.
An assessment study of these equations is conducted against the
experimental data; and the satisfaction of the criteria regarding the
acceptance of parametric equations is checked. Significant effort has
been devoted by researchers to the study of SCFs in various uniplanar
tubular connections. Nevertheless, for multi-planar joints
covering the majority of practical applications, very few
investigations have been reported due to the complexity and high
cost involved.
Abstract: The objective of this work is to present a expertise on
flooding hazard analysis and how to reduce the risk. The analysis
concerns the disaster induced by the flood on November 10/11, 2001
in the Bab El Oued district of the city of Algiers.The study begins by
an expertise of damages in related with the urban environment and
the history of the urban growth of the site. After this phase, the work
is focalized on the identification of the existing correlations between
the development of the town and its vulnerability. The final step
consists to elaborate the interpretations on the interactions between
the urban growth, the sewerage network and the vulnerability of the
urban system.In conclusion, several recommendations are formulated
permitting the mitigation of the risk in the future. The principal
recommendations concern the new urban operations and the existing
urbanized sites.
Abstract: Many non-conventional adsorbent have been studied
as economic alternative to commercial activated carbon and mostly
agricultural waste have been introduced such as rubber leaf powder
and hazelnut shell. Microwave Incinerated Rice Husk Ash
(MIRHA), produced from the rice husk is one of the low-cost
materials that were used as adsorbent of heavy metal. The aim of
this research was to study the feasibility of using MIRHA500 and
MIRHA800 as adsorbent for the removal of Cu(II) metal ions from
aqueous solutions by the batch studies. The adsorption of Cu(II) into
MIRHA500 and MIRH800 favors Fruendlich isotherm and imply
pseudo – kinetic second order which applied chemisorptions
Abstract: According to the masonry standard the compressive
strength is basically dependent on factors such as the mortar strength
and the relative values of unit and mortar strength. However
interlocking brick has none or less use of mortar. Therefore there is a need to investigate the behavior of masonry walls using interlocking
bricks. In this study a series of tests have been conducted; physical
properties and compressive strength of brick units and masonry walls
were constructed from interlocking bricks and tested under constant
vertical load at different eccentricities. The purpose of the
experimental investigations is to obtain the force displacement curves, analyze the behavior of masonry walls. The results showed
that the brick is categorized as common brick (BS 3921:1985) and severe weathering grade (ASTM C62). The maximum compressive stress of interlocking brick wall is 3.6 N/mm2 and fulfilled the requirement of standard for residential building.
Abstract: In this study, the effect of greywater irrigation on airwater interfacial area is investigated. Several soil column experiments were conducted for different greywater irrigation to develop the pressure-saturation curves. Surface tension was measured for different greywater concentration and fitted for Gibbs adsorption equation. Pressure-saturation curves show that the reduction of capillary rise stops when it reaches its critical micelle concentration (CMC). A simple theory is derived from pressure-saturation curves for calculating air-water interfacial area in porous medium during greywater irrigation by introducing a term 'hydraulic radius' for the pores. This term diminishes any effect of pore shapes on the air-water interfacial area. The air-water interfacial area was calculated using the pressure-saturation curves and found that it decreases with increasing moisture content. But no significant effect was observed on air-water interfacial area for different greywater irrigation. A maximum of 10% variation in interfacial area was observed at the residual saturation zone.
Abstract: In the territories where high-intensity
earthquakes are frequent is paid attention to the solving of the
seismic problems. In the paper are described two
computational model variants based on finite element method
of the construction with different subsoil simulation (rigid or
elastic subsoil) is used. For simulation and calculations
program system based on method final elements ANSYS was
used. Seismic responses calculations of residential building
structure were effected on loading characterized by
accelerogram for comparing with the responses spectra
method.
Abstract: Earth reinforcing techniques have become useful and economical to solve problems related to difficult grounds and provide satisfactory foundation performance. In this context, this paper uses radial basis function neural network (RBFNN) for predicting the bearing pressure of strip footing on reinforced granular bed overlying weak soil. The inputs for the neural network models included plate width, thickness of granular bed and number of layers of reinforcements, settlement ratio, water content, dry density, cohesion and angle of friction. The results indicated that RBFNN model exhibited more than 84 % prediction accuracy, thereby demonstrating its application in a geotechnical problem.
Abstract: Steel made pipelines with different diameters are used
for transmitting oil and gas which in many cases are buried in soil
under the sea bed or immersed in sea water. External corrosion of
pipes is an important form of deterioration due to the aggressive
environment of sea water. Corrosion normally results in pits. Hence,
using the finite element method, namely ABAQUS software, this
paper estimates the amount of pressure capacity reduction of a pipecontaining
a semi-elliptical pitting corrosion and the rate of corrosion
during the pipeline life of 25 years.
Abstract: The Eulerian numerical method is proposed to analyze
the explosion in tunnel. Based on this method, an original software
M-MMIC2D is developed by Cµ program language. With this
software, the explosion problem in the tunnel with three
expansion-chambers is numerically simulated, and the results are
found to be in full agreement with the observed experimental data.
Abstract: The purpose of this study is mainly to predict collision
frequency on the horizontal tangents combined with vertical curves
using artificial neural network methods. The proposed ANN models
are compared with existing regression models. First, the variables
that affect collision frequency were investigated. It was found that
only the annual average daily traffic, section length, access density,
the rate of vertical curvature, smaller curve radius before and after
the tangent were statistically significant according to related
combinations. Second, three statistical models (negative binomial,
zero inflated Poisson and zero inflated negative binomial) were
developed using the significant variables for three alignment
combinations. Third, ANN models are developed by applying the
same variables for each combination. The results clearly show that
the ANN models have the lowest mean square error value than those
of the statistical models. Similarly, the AIC values of the ANN
models are smaller to those of the regression models for all the
combinations. Consequently, the ANN models have better statistical
performances than statistical models for estimating collision
frequency. The ANN models presented in this paper are
recommended for evaluating the safety impacts 3D alignment
elements on horizontal tangents.
Abstract: The presented article deals with the description of a
numerical model of a corridor at a Central Interim Spent Fuel Storage
Facility (hereinafter CISFSF). The model takes into account the
effect of air flows on the temperature of stored waste. The
computational model was implemented in the ANSYS/CFX
programming environment in the form of a CFD task solution, which
was compared with an approximate analytical calculation. The article
includes a categorization of the individual alternatives for the
ventilation of such underground systems. The aim was to evaluate a
ventilation system for a CISFSF with regard to its stability and
capacity to provide sufficient ventilation for the removal of heat
produced by stored casks with spent nuclear fuel.
Abstract: In the present article, effect of non-uniform excitation
of reservoir bottom on nonlinear response of concrete gravity dams is
considered. Anisotropic damage mechanics approach is used to model nonlinear behavior of mass concrete in 2D space. The tallest
monolith of Pine Flat dam is selected as a case study. The horizontal
and vertical components of 1967 Koyna earthquake is used to excite
the system. It is found that crest response and stresses within the dam body decrease significantly when the reservoir is excited nonuniformly. In addition, the crack profiles within the dam body and in vicinity of the neck decreases.
Abstract: We study dynamic instability in high-rise steel moment
resisting frames (SMRFs) subjected to synthetic long-period ground
motions caused by hypothetical huge subduction earthquakes. Since
long duration as well as long dominant periods is a characteristic of
long-period ground motions, interstory drifts may enter the negative
postyield stiffness range many times when high-rise buildings are
subjected to long-period ground motions. Through the case studies of
9 high-rise SMRFs designed in accordance with the Japanese design
practice in 1980s, we demonstrate that drifting, or accumulation of
interstory drifts in one direction, occurs at the lower stories of the
SMRFs, if their natural periods are close to the dominant periods of the
long-period ground motions. The drifting led to residual interstory
drift ratio over 0.01, or to collapse if the design base shear was small.
Abstract: In this paper, the modified optimal sliding mode control with a proposed method to design a sliding surface is presented. Because of the inability of the previous approach of the sliding mode method to design a bounded and suitable input, the new variation is proposed in the sliding manifold to obviate problems in a structural system. Although the sliding mode control is a powerful method to reject disturbances and noises, the chattering problem is not good for actuators. To decrease the chattering phenomena, the optimal control is added to the sliding mode control. Not only the proposed method can decline the intense variations in the inputs of the system but also it can produce the efficient responses respect to the sliding mode control and optimal control that are shown by performing some numerical simulations.
Abstract: Demolitions of buildings have created a lot of waste
and one of it is clay bricks. The waste clay bricks were ground to
roughly cement fineness and used to partially replaced cement at
10%, 20% and 30% with w/b ratio of 0.6 and tested at 7, 28, 60, 90
and 120 days. The result shows that the compressive strength of GCB
concrete increases over age however, decreases as the level of
replacements increases. It was also found that 10% replacement of
GCB gave the highest compressive strength, however for optimum
replacement, 30% was chosen as it still attained strength of grade 30
concrete. In terms of durability performances, results show that GCB
replacement up to 30% was found to be efficient in reducing water
absorption as well as water permeability. These studies show that
GCB has the potential to be used as partial cement replacement in
making concrete.
Abstract: Decomposition processes take place in landfill
generate leachates that can be categorized mainly of acetogenic and
methanogenic in nature. BOD:COD ratio computed in this study for a
landfill site over a 3 years duration revealed as a good indicator to
identify acetogenic leachate from methanogenic leachate. Correlation
relationships to predict pollutant level taking into consideration of
climatic condition are derived.