Abstract: Reinforced Concrete (RC) deep beams are special structural elements because of their geometry and behavior under loads. For example, assumption of strain- stress distribution is not linear in the cross section. These types of beams may have simple supports or fixed supports. A lot of research works have been conducted on simply supported deep beams, but little study has been done in the fixed-end RC deep beams behavior. Recently, using of fixed-ended deep beams has been widely increased in structures. In this study, the behavior of fixed-ended deep beams is investigated, and the important parameters in capacity of this type of beams are mentioned.
Abstract: The tall windmill towers are designed as monopole tower or lattice tower. In the present research, a 125-meter high hybrid tower which is a combination of lattice and monopole type is proposed. The response of hybrid tower is compared with conventional monopole tower. The towers were analyzed in finite element method software considering nonlinear seismic time history load. The synthetic seismic time history for different soil is derived using the SeismoARTIF software. From the present research, it is concluded that, in the hybrid tower, we are not getting resonance condition. The base shear is less in hybrid tower compared to monopole tower for different soil conditions.
Abstract: Modal analysis of a FGM plate containing the ceramic phase of Al2O3 and metal phase of stainless steel 304 was performed using ABAQUS, with the assumptions that the material has an elastic mechanical behavior and its Young modulus and density are varying in thickness direction. For this purpose, a subroutine was written in FOTRAN and linked with ABAQUS. First, a simulation was performed in accordance to other researcher’s model, and then after comparing the obtained results, the accuracy of the present study was verified. The obtained results for natural frequency and mode shapes indicate good performance of user-written subroutine as well as FEM model used in present study. After verification of obtained results, the effect of clamping condition and the material type (i.e. the parameter n) was investigated. In this respect, finite element analysis was carried out in fully clamped condition for different values of n. The results indicate that the natural frequency decreases with increase of n, since with increase of n, the amount of ceramic phase in FGM plate decreases, while the amount of metal phase increases, leading to decrease of the plate stiffness and hence, natural frequency, as the Young modulus of Al2O3 is equal to 380 GPa and the Young modulus of stainless steel 304 is equal to 207 GPa.
Abstract: Handwriting is essential to academic success; however, the current literature is limited in the identification of pre-handwriting skills. The purpose of this study was to identify the pre-handwriting skills, which occupational therapy practitioners deem important to handwriting success, as well as those which aid in intervention planning. The online survey instrument consisted of 33 questions that assessed various skills related to the development of handwriting, as well as captured demographic information. Both occupational therapists and occupational therapy assistants were included in the survey study. The survey found that the respondents were in agreement that purposeful scribbling, the ability of a child to copy (vertical/horizontal lines, circle, squares, and triangles), imitating an oblique cross, cognitive skills (attention, praxis, self-regulation, sequencing), grasp patterns, hand dominance, in hand manipulation skills (shift, translation, rotation), bilateral integration, stabilization of paper, crossing midline, and visual perception were important indicators of handwriting readiness. The results of the survey support existing research regarding the skills necessary for the successful development of handwriting in children.
Abstract: The 3D body movement signals captured during
human-human conversation include clues not only to the content of
people’s communication but also to their culture and personality.
This paper is concerned with automatic extraction of this information
from body movement signals. For the purpose of this research, we
collected a novel corpus from 27 subjects, arranged them into groups
according to their culture. We arranged each group into pairs and
each pair communicated with each other about different topics.
A state-of-art recognition system is applied to the problems of
person, culture, and topic recognition. We borrowed modeling,
classification, and normalization techniques from speech recognition.
We used Gaussian Mixture Modeling (GMM) as the main technique
for building our three systems, obtaining 77.78%, 55.47%, and
39.06% from the person, culture, and topic recognition systems
respectively. In addition, we combined the above GMM systems with
Support Vector Machines (SVM) to obtain 85.42%, 62.50%, and
40.63% accuracy for person, culture, and topic recognition
respectively.
Although direct comparison among these three recognition
systems is difficult, it seems that our person recognition system
performs best for both GMM and GMM-SVM, suggesting that intersubject
differences (i.e. subject’s personality traits) are a major
source of variation. When removing these traits from culture and
topic recognition systems using the Nuisance Attribute Projection
(NAP) and the Intersession Variability Compensation (ISVC)
techniques, we obtained 73.44% and 46.09% accuracy from culture
and topic recognition systems respectively.
Abstract: The aluminum impregnated catalysts of Al-alumina (Al-Al2O3), Al-montmorillonite (Al-Mmn) and Al-activated charcoal (Al-AC) of various percent loadings were prepared by wet impregnation method and characterized by SEM, XRD and N2 adsorption/desorption (BET). The catalytic properties were investigated in the degradation of waste polystyrene (WPS). The results of catalytic degradation of Al metal, 20% Al-Al2O3, 5% Al-Mmn and 20% Al-AC were compared with each other for optimum conditions. Among the catalyst used 20% Al-Al2O3 was found the most effective catalyst. The BET surface area of 20% Al-Al2O3 determined was 70.2 m2/g. The SEM data revealed the catalyst with porous structure throughout the frame work with small nanosized crystallites. The yield of liquid products with 20% Al-Al2O3 (91.53 ± 2.27 wt%) was the same as compared to Al metal (91.20 ± 0.35 wt%) but the selectivity of hydrocarbons and yield of styrene monomer (56.32 wt%) was higher with 20% Al-Al2O3 catalyst.
Abstract: Recognizing behavioral patterns of financial markets
is essential for traders. Japanese candlestick chart is a common tool to
visualize and analyze such patterns in an economic time series. Since
the world was introduced to Japanese candlestick charting, traders
saw how combining this tool with intelligent technical approaches
creates a powerful formula for the savvy investors.
This paper propose a generalization to box counting method of
Grassberger-Procaccia, which is based on computing the correlation
dimension of Japanese candlesticks instead commonly used 'close'
points. The results of this method applied on several foreign
exchange rates vs. IRR (Iranian Rial). Satisfactorily show lower
chaotic dimension of Japanese candlesticks series than regular
Grassberger-Procaccia method applied merely on close points of
these same candles. This means there is some valuable information
inside candlesticks.
Abstract: In this article, by using fuzzy AHP and TOPSIS
technique we propose a new method for project selection problem.
After reviewing four common methods of comparing alternatives
investment (net present value, rate of return, benefit cost analysis
and payback period) we use them as criteria in AHP tree. In this
methodology by utilizing improved Analytical Hierarchy Process
by Fuzzy set theory, first we try to calculate weight of each
criterion. Then by implementing TOPSIS algorithm, assessment of
projects has been done. Obtained results have been tested in a
numerical example.