Abstract: In the present work we developed an image processing
algorithm to measure water droplets characteristics during dropwise
condensation on pillared surfaces. The main problem in this process is
the similarity between shape and size of water droplets and the pillars.
The developed method divides droplets into four main groups based
on their size and applies the corresponding algorithm to segment each
group. These algorithms generate binary images of droplets based
on both their geometrical and intensity properties. The information
related to droplets evolution during time including mean radius and
drops number per unit area are then extracted from the binary images.
The developed image processing algorithm is verified using manual
detection and applied to two different sets of images corresponding
to two kinds of pillared surfaces.
Abstract: Various processes are modelled using a discrete phase,
where particles are seeded from a source. Such particles can represent
liquid water droplets, which are affecting the continuous phase by
exchanging thermal energy, momentum, species etc. Discrete phases
are typically modelled using parcel, which represents a collection of
particles, which share properties such as temperature, velocity etc.
When coupling the phases, the exchange rates are integrated over
the cell, in which the parcel is located. This can cause spikes and
fluctuating exchange rates. This paper presents an alternative method of coupling a discrete
and a continuous plug flow phase. This is done using triangular
parcels, which span between nodes following the dynamics of single
droplets. Thus, the triangular parcels are propagated using the corner
nodes. At each time step, the exchange rates are spatially integrated
over the surface of the triangular parcels, which yields a smooth
continuous exchange rate to the continuous phase. The results shows that the method is more stable, converges
slightly faster and yields smooth exchange rates compared with
the steam tube approach. However, the computational requirements
are about five times greater, so the applicability of the alternative
method should be limited to processes, where the exchange rates are
important. The overall balances of the exchanged properties did not
change significantly using the new approach.
Abstract: Surface topography plays a significant role in the functional performance of engineered parts. It is important to have a control on the surface geometry and understanding on the surface details to get the desired performance. Hence, in the current research contribution, a non-contact micro-texturing technique has been explored and developed. The technique involves ultrasonic excitation of a tool as a prime source of surface texturing for aluminum alloy workpieces. The specimen surface is polished first and is then immersed in a liquid bath containing 10% weight concentration of Ti6Al4V grade 5 spherical powders. A submerged slurry jet is used to recirculate the spherical powders under the ultrasonic horn which is excited at an ultrasonic frequency and amplitude of 40 kHz and 70 µm respectively. The distance between the horn and workpiece surface was remained fixed at 200 µm using a precision control stage. Texturing effects were investigated for different process timings of 1, 3 and 5 s. Thereafter, the specimens were cleaned in an ultrasonic bath for 5 mins to remove loose debris on the surface. The developed surfaces are characterized by optical and contact surface profiler. The optical microscopic images show a texture of circular spots on the workpiece surface indented by titanium spherical balls. Waviness patterns obtained from contact surface profiler supports the texturing effect produced from the proposed technique. Furthermore, water droplet tests were performed to show the efficacy of the proposed technique to develop hydrophilic surfaces and to quantify the texturing effect produced.
Abstract: With the rapid development of national modern industry, people begin to pay attention to environmental pollution and harm caused by industrial dust. Based on above, a numerical study on the dedusting technology of industrial environment was conducted. The dynamic models of multicomponent particles collision and coagulation, breakage and deposition are developed, and the interaction of water droplet and aerosol particle in 2-Dimension flow field was researched by Eulerian-Lagrangian method and Multi-Monte Carlo method. The effects of the droplet scale, movement speed of droplet and the flow field structure on scavenging efficiency were analyzed. The results show that under the certain condition, 30μm of droplet has the best scavenging efficiency. At the initial speed 1m/s of droplets, droplets and aerosol particles have more time to interact, so it has a better scavenging efficiency for the particle.
Abstract: The reduction of water content in crude oil emulsions reduces pipeline corrosion potential and increases the productivity. Chemical emulsification of crude oil emulsions is one of the methods available to reduce the water content. Presence of demulsifier causes the film layer between the crude oil emulsion and water droplets to become unstable leading to the acceleration of water coalescence. This research has been performed to study the improvement performance of a chemical demulsifier by silica nanoparticles. The silica nano-particles have been synthesized by sol-gel technique and precipitation using poly vinyl alcohol (PVA) and poly ethylene glycol (PEG) as surfactants and then nano-particles are added to the demulsifier. The silica nanoparticles were characterized by Particle Size Analyzer (PSA) and SEM. Upon the addition of nanoparticles, bottle tests have been carried out to separate and measure the water content. The results show that silica nano-particles increase the demulsifier efficiency by about 40%.
Abstract: Superhydrophobic surfaces are abundant in nature. Several surfaces such as wings of butterfly, legs of water strider, feet of gecko and the lotus leaf show extreme water repellence behaviour. Self-cleaning, stain-free fabrics, spill-resistant protective wears, drag reduction in micro-fluidic devices etc. are few applications of superhydrophobic surfaces. In order to design robust superhydrophobic surface, it is important to understand the interaction of water with superhydrophobic surface textures. In this work, we report a simple coating method for creating large-scale flexible superhydrophobic paper surface. The surface consists of multiple layers of silanized zirconia microparticles decorated with zirconia nanoparticles. Water contact angle as high as 159±10 and contact angle hysteresis less than 80 was observed. Drop impact studies on superhydrophobic paper surface were carried out by impinging water droplet and capturing its dynamics through high speed imaging. During the drop impact, the Weber number was varied from 20 to 80 by altering the impact velocity of the drop and the parameters such as contact time, normalized spread diameter were obtained. In contrast to earlier literature reports, we observed contact time to be dependent on impact velocity on superhydrophobic surface. Total contact time was split into two components as spread time and recoil time. The recoil time was found to be dependent on the impact velocity while the spread time on the surface did not show much variation with the impact velocity. Further, normalized spreading parameter was found to increase with increase in impact velocity.
Abstract: The use of titanium fluoride and iron fluoride
(TiF3/FeF3) catalysts in combination with polutetrafluoroethylene
(PTFE) in plain zinc- dialkyldithiophosphate (ZDDP) oil is important
for the study of engine tribocomponents and is increasingly a strategy
to improve the formation of tribofilm and provide low friction and
excellent wear protection in reduced phosphorus plain ZDDP oil. The
influence of surface roughness and the concentration of
TiF3/FeF3/PTFE were investigated using bearing steel samples
dipped in lubricant solution at 100°C for two different heating time
durations. This paper addresses the effects of water drop contact
angle using different surface; finishes after treating them with
different lubricant combination. The calculated water drop contact
angles were analyzed using Design of Experiment software (DOE)
and it was determined that a 0.05 μm Ra surface roughness would
provide an excellent TiF3/FeF3/PTFE coating for antiwear resistance
as reflected in the Scanning electron microscopy (SEM) images and
the tribological testing under extreme pressure conditions. Both
friction and wear performance depend greatly on the PTFE/and
catalysts in plain ZDDP oil with 0.05 % phosphorous and on the
surface finish of bearing steel. The friction and wear reducing effects,
which was observed in the tribological tests, indicated a better micro
lubrication effect of the 0.05 μm Ra surface roughness treated at
100°C for 24 hours when compared to the 0.1 μm Ra surface
roughness with the same treatment.
Abstract: Wet scrubbers have found widespread use in cleaning
contaminated gas streams because of their ability to remove
particulates and based on the applications of scrubbing of marine
engine exhaust gases by spraying sea-water. In order to examine the
flow characteristics inside the scrubber, the model is designated with
flow properties of hot air and water sprayer. The flow dynamics of
evaporation of hot air by the injection of water droplets is the key
factor considered in this paper. The flow behavior inside the scrubber
was investigated from the previous works and to sum up the
evaporation rate with respect to the concentration of water droplets are
predicted to bring out the competent modelling. The numerical
analysis using CFD facilitates in understanding the problem better and
empathies the behavior of the model over its entire operating envelope.
Abstract: In this work we investigated the behavior of methane
hydrates dispersed in crude oils from different fields at temperatures
below 0°C. In case of crude oil emulsion the size of water droplets is
in the range of 50e100"m. The size of hydrate particles formed from
droplets is the same. The self-preservation is not expected in this
field. However, the self-preservation of hydrates with the size of
particles 24±18"m (electron microscopy data) in suspensions is
observed. Similar results were obtained for four different kinds of
crude oil and model system such as asphaltenes, resins and wax in ndecane.
This result can allow developing effective methods to prevent
the formation and elimination of gas-hydrate plugs in pipelines under
low temperature conditions (e. g. in Eastern Siberia). There is a
prospective to use experiment results for working out the technology
of associated petroleum gas recovery.
Abstract: Economic Load Dispatch (ELD) is a method of determining
the most efficient, low-cost and reliable operation of a power
system by dispatching available electricity generation resources to
supply load on the system. The primary objective of economic
dispatch is to minimize total cost of generation while honoring
operational constraints of available generation resources. In this paper
an intelligent water drop (IWD) algorithm has been proposed to
solve ELD problem with an objective of minimizing the total cost of
generation. Intelligent water drop algorithm is a swarm-based natureinspired
optimization algorithm, which has been inspired from natural
rivers. A natural river often finds good paths among lots of possible
paths in its ways from source to destination and finally find almost
optimal path to their destination. These ideas are embedded into
the proposed algorithm for solving economic load dispatch problem.
The main advantage of the proposed technique is easy is implement
and capable of finding feasible near global optimal solution with
less computational effort. In order to illustrate the effectiveness of
the proposed method, it has been tested on 6-unit and 20-unit test
systems with incremental fuel cost functions taking into account the
valve point-point loading effects. Numerical results shows that the
proposed method has good convergence property and better in quality
of solution than other algorithms reported in recent literature.
Abstract: This paper investigates the influence of various
parameters on the behaviour of water droplets on polymeric surfaces
under high electric fields. An inclined plane test was carried out to
understand the droplet behaviour in strong electric field. Parameters
such as water droplet conductivity, droplet volume, polymeric
surface roughness and droplet positioning with respect to the
electrodes were studied. The flashover voltage is affected by all
aforementioned parameters. The droplet positioning is in some cases
more vital than the droplet volume. Surface damages were analysed
using Scanning Electron Microscopy (SEM) studies and by Energy
dispersive X-ray Analysis (EDAX). It is observes that magnitude of
discharge have direct influence on amount of surface da
Abstract: In the present work, an attempt has been made to
understand the feasibility of using UHF technique for identification
of any corona discharges/ arcing in insulating material due to water
droplets. The sensors of broadband type are useful for identification
of such discharges. It is realised that arcing initiated by liquid droplet
radiates UHF signals in the entire bandwidth up to 2 GHz. The
frequency content of the UHF signal generated due to corona/arcing
is not much varied in epoxy nanocomposites with different weight
percentage of clay content. The exfoliated/intercalated properties
were analysed through TEM studies. It is realized that corona
initiated discharges are of intermittent process. The hydrophobicity
of the material characterized through contact angle measurement. It
is realized that low Wt % of nanoclay content in epoxy resin reduces
the surface carbonization due to arcing/corona discharges. The results
of the study with gamma irradiated specimen indicates that contact
angle, discharge inception time and evaporation time of the liquid are
much lower than the virgin epoxy nanocomposite material.
Abstract: Two different superhydrophobic surfaces were
elaborated and their oil repellency behavior was evaluated using
several liquid with different surface tension. A silicone rubber/SiO2
nanocomposite coated (A) on aluminum substrate by “spin-coating"
and the sample B was an anodized aluminum surface covered by
Teflon-like coating. A high static contact angle about ∼162° was
measured for two prepared surfaces on which the water droplet rolloff.
Scanning electron microscopy (SEM) showed the presence of
micro/nanostructures for both sample A and B similar to that of lotus
leaf.
However the sample A presented significantly different behaviour
of wettability against the low surface tension liquid. Sample A has
been wetted totally by oil (dodecan) droplet while sample B showed
oleophobic behaviour. Oleophobic property of Teflon like coating
can be contributed to the presence of CF2 and CF3 functional group
which was shown by XPS analysis.
Abstract: Observations show that power plant efficiency
decreases in hot summer days. Water droplet injection in air
condensers is suggested in order to decrease the inlet air temperature.
Nozzle arrangement, injected water flow rate and droplets diameter
effects on evaporation rate and the resulting air temperature are
investigated using numerical simulation. Decreasing the diameter of
injected droplets and increasing the number of injecting nozzles,
decreases the outlet air temperature. Also a more uniform air
temperature can be obtained using more injecting nozzles. Numerical
results are in good agreement with analytical results.
Abstract: Different numerical methods are employed and developed for simulating interfacial flows. A large range of applications belong to this group, e.g. two-phase flows of air bubbles in water or water drops in air. In such problems surface tension effects often play a dominant role. In this paper, various models of surface tension force for interfacial flows, the CSF, CSS, PCIL and SGIP models have been applied to simulate the motion of small air bubbles in water and the results were compared and reviewed. It has been pointed out that by using SGIP or PCIL models, we are able to simulate bubble rise and obtain results in close agreement with the experimental data.
Abstract: This paper presents the simulation results of electric field and potential distributions along surface of silicone rubber polymer insulators under clean and various contamination conditions with/without water droplets. Straight sheds insulator having leakage distance 290 mm was used in this study. Two type of contaminants, playwood dust and cement dust, have been studied the effect of contamination on the insulator surface. The objective of this work is to comparison the effect of contamination on potential and electric field distributions along the insulator surface when water droplets exist on the insulator surface. Finite element method (FEM) is adopted for this work. The simulation results show that contaminations have no effect on potential distribution along the insulator surface while electric field distributions are obviously depended on contamination conditions.
Abstract: The paper presents a one-dimensional transient
mathematical model of thermal oil-water two-phase emulsion flows
in pipes. The set of the mass, momentum and enthalpy conservation
equations for the continuous fluid and droplet phases are solved. Two
friction correlations for the continuous fluid phase to wall friction are
accounted for in the model and tested. The aerodynamic drag force
between the continuous fluid phase and droplets is modeled, too. The
density and viscosity of both phases are assumed to be constant due
to adiabatic experimental conditions. The proposed mathematical
model is validated on the experimental measurements of oil-water
emulsion flows in horizontal pipe [1,2]. Numerical analysis on
single- and two-phase oil-water flows in a pipe is presented in the
paper. The continuous oil flow having water droplets is simulated.
Predictions, which are performed by using the presented model, show
excellent agreement with the experimental data if the water fraction is
equal or less than 10%. Disagreement between simulations and
measurements is increased if the water fraction is larger than 10%.
Abstract: We developed a method based on quasi-molecular
modelling to simulate the fall of water drops on horizontally smooth
and rough surfaces. Each quasi-molecule was a group of particles
that interacted in a fashion entirely analogous to classical Newtonian
molecular interactions. When a falling water droplet was simulated at
low impact velocity on both smooth and rough surfaces, the droplets
moved periodically (i.e. the droplets moved up and down for a
certain period, finally they stopped moving and reached a steady
state), spreading and recoiling without splash or break-up. Spreading
rates of falling water droplets increased rapidly as time increased
until the spreading rate reached its steady state at time t ~ 0.25 s for
rough surface and t ~ 0.40 s for smooth surface. The droplet height
above both surfaces decreased as time increased, remained constant
after the droplet diameter attained a maximum value and reached its
steady state at time t ~ 0.4 s. However, rough surface had higher
spreading rates of falling water droplets and lower height on the
surface than smooth one.
Abstract: The effects of down slope steepness on soil splash distribution under a water drop impact have been investigated in this study. The equipment used are the burette to simulate a water drop, a splash cup filled with sandy soil which forms the source area and a splash board to collect the ejected particles. The results found in this study have shown that the apparent mass increased with increasing downslope angle following a linear regression equation with high coefficient of determination. In the same way, the radial soil splash distribution over the distance has been analyzed statistically, and an exponential function was the best fit of the relationship for the different slope angles. The curves and the regressions equations validate the well known FSDF and extend the theory of Van Dijk.