Abstract: Fe-based amorphous feedstock powders are used as the matrix into which various ratios of hard B4C nanoparticles (0, 5, 10, 15, 20 vol.%) as reinforcing agents were prepared using a planetary high-energy mechanical milling. The ball-milled nanocomposite feedstock powders were also sprayed by means of high-velocity oxygen fuel (HVOF) technique. The characteristics of the powder particles and the prepared coating depending on their microstructures and nanohardness were examined in detail using nanoindentation tester. The results showed that the formation of the Fe-based amorphous phase was noticed over the course of high-energy ball milling. It is interesting to note that the nanocomposite coating is divided into two regions, namely, a full amorphous phase region and homogeneous dispersion of B4C nanoparticles with a scale of 10–50 nm in a residual amorphous matrix. As the B4C content increases, the nanohardness of the composite coatings increases, but the fracture toughness begins to decrease at the B4C content higher than 20 vol.%. The optimal mechanical properties are obtained with 15 vol.% B4C due to the suitable content and uniform distribution of nanoparticles. Consequently, the changes in mechanical properties of the coatings were attributed to the changes in the brittle to ductile transition by adding B4C nanoparticles.
Abstract: The reliability of the power grid depends on the successful operation of thousands of protective relays. The failure of one relay to operate as intended may lead the entire power grid to blackout. In fact, major power system failures during transient disturbances may be caused by unnecessary protective relay tripping rather than by the failure of a relay to operate. Adequate relay testing provides a first defense against false trips of the relay and hence improves power grid stability and prevents catastrophic bulk power system failures. The goal of this research project is to design and enhance the relay tester using a technology such as Field Programmable Gate Array (FPGA) card NI 7851. A PC based tester framework has been developed using Simulink power system model for generating signals under different conditions (faults or transient disturbances) and LabVIEW for developing the graphical user interface and configuring the FPGA. Besides, the interface system has been developed for outputting and amplifying the signals without distortion. These signals should be like the generated ones by the real power system and large enough for testing the relay’s functionality. The signals generated that have been displayed on the scope are satisfactory. Furthermore, the proposed testing system can be used for improving the performance of protective relay.
Abstract: The iron content of the ore used is crucial for the productivity and coke consumption rate in blast furnace pig iron production. Therefore, most iron ore deposits are processed in beneficiation plants to increase the iron content and remove impurities. In several comminution stages, the particle size of the ore is reduced to ensure that the iron oxides are physically liberated from the gangue. Subsequently, physical separation processes are applied to concentrate the iron ore. The fine-grained ore concentrates produced need to be transported, stored, and processed. For smooth operation of these processes, the flow properties of the material are crucial. The flowability of powders depends on several properties of the material: grain size, grain size distribution, grain shape, and moisture content of the material. The flowability of powders can be measured using ring shear testers. In this study, the influence of the moisture content on the flowability for the Krivoy Rog magnetite iron ore concentrate was investigated. Dry iron ore concentrate was mixed with varying amounts of water to produce samples with a moisture content in the range of 0.2 to 12.2%. The flowability of the samples was investigated using a Schulze ring shear tester. At all measured values of the normal stress (1.0 kPa – 20 kPa), the flowability decreased significantly from dry ore to a moisture content of approximately 3-5%. At higher moisture contents, the flowability was nearly constant, while at the maximum moisture content the flowability improved for high values of the normal stress only. The results also showed an improving flowability with increasing consolidation stress for all moisture content levels investigated. The wall friction angle of the dust with carbon steel (S235JR), and an ultra-high molecule low-pressure polyethylene (Robalon) was also investigated. The wall friction angle increased significantly from dry ore to a moisture content of approximately 3%. For higher moisture content levels, the wall friction angles were nearly constant. Generally, the wall friction angle was approximately 4° lower at the higher wall normal stress.
Abstract: The impact of boron doping on the internal friction (IF) and shear modulus temperature spectra of Si1-xGex(x≤0,02) monocrsytals has been investigated by reverse torsional pendulum oscillations characteristics testing. At room temperatures, microhardness and indentation modulus of the same specimens have been measured by dynamic ultra microhardness tester. It is shown that boron doping causes two kinds effect: At low boron concentration (~1015 cm-3) significant strengthening is revealed, while at the high boron concentration (~1019 cm-3) strengthening effect and activation characteristics of relaxation origin IF processes are reduced.
Abstract: Hard coatings are widely used in cutting and forming
tool industries. Titanium Nitride (TiN) possesses good hardness,
strength, and corrosion resistance. The coating properties are
influenced by many process parameters. The coatings were deposited
on steel substrate by changing the process parameters such as
substrate temperature, nitrogen flow rate and target power in a D.C
planer magnetron sputtering. The structure of coatings were analysed
using XRD. The hardness of coatings was found using Micro
hardness tester. From the experimental data, a regression model was
developed and the optimum response was determined using Response
Surface Methodology (RSM).
Abstract: The main idea of this work is to investigate the effect
of knitted fabrics characteristics on moisture management properties.
Wetting and transport properties of single jersey, Rib 1&1 and
English Rib fabrics made out of cotton and blended Cotton/Polyester
yarns were studied. The dynamic water sorption of fabrics was
investigated under same isothermal and terrestrial conditions at
20±2°C-65±4% by using the Moisture Management Tester (MMT)
which can be used to quantitatively measure liquid moisture transfer
in one step in a fabric in multidirections: Absorption rate, moisture
absorbing time of the fabric's inner and outer surfaces, one-way
transportation capability, the spreading/drying rate, the speed of
liquid moisture spreading on fabric's inner and outer surfaces are
measured, recorded and discussed. The results show that fabric’s
composition and knit’s structure have a significant influence on those
phenomena.
Abstract: The present work analyses different parameters of end
milling to minimize the surface roughness for AISI D2 steel. D2 Steel
is generally used for stamping or forming dies, punches, forming
rolls, knives, slitters, shear blades, tools, scrap choppers, tyre
shredders etc. Surface roughness is one of the main indices that
determines the quality of machined products and is influenced by
various cutting parameters. In machining operations, achieving
desired surface quality by optimization of machining parameters, is a
challenging job. In case of mating components the surface roughness
become more essential and is influenced by the cutting parameters,
because, these quality structures are highly correlated and are
expected to be influenced directly or indirectly by the direct effect of
process parameters or their interactive effects (i.e. on process
environment). In this work, the effects of selected process parameters
on surface roughness and subsequent setting of parameters with the
levels have been accomplished by Taguchi’s parameter design
approach. The experiments have been performed as per the
combination of levels of different process parameters suggested by
L9 orthogonal array. Experimental investigation of the end milling of
AISI D2 steel with carbide tool by varying feed, speed and depth of
cut and the surface roughness has been measured using surface
roughness tester. Analyses of variance have been performed for mean
and signal-to-noise ratio to estimate the contribution of the different
process parameters on the process.