Abstract: Expansive soils are often encountered in many parts
of the world, especially in arid and semi-arid fields. Such kind of
soils, generally including active clay minerals in low water content,
enlarge in volume by absorbing the water through the surface and
cause a great harm to the light structures such as channel coating,
roads and airports. The expansive soils were encountered on the path
of Apa-Hotamış conveyance channel belonging to the State
Hydraulic Works in the region of Konya. In the research done in this
area, it is predicted that the soil has a swollen nature and the soil
should be filled with proper granular equipments by digging the
ground to 50-60 cm. In this study, for purpose of helping the other
research to be done in the same area, it is thought that instead of
replacing swollen soil with the granular soil, by stabilizing it with
polypropylene fiber and using it its original place decreases effect of
swelling percent, in this way the cost will be decreased. Therefore,
laboratory tests were conducted to study the effects of polypropylene
fiber on swelling characteristics of expansive soil. Test results
indicated that inclusion of fiber reduced swell percent of expansive
soil. As the fiber content increased, the unconfined compressive
strength was increased. Finally, it can be said that stabilization of
expansive soils with polypropylene fiber is an effective method.
Abstract: Cross-linked konjac glucomannan and kappa
carrageenan film were prepared by chemical crosslinking using
glutaraldehyde (GA) as the crosslinking agent. The effect
crosslinking on the swelling degree was investigated. Konjac
glucomannan and its mixture with kappa carrageenan film was
immersed in GA solution and then thermally cured. The obtained
cross-linked film was washed and soaked in the ethanol to remove
the unreacted GA. The obtained film was air dried at room
temperature to a constant weight. The infrared spectra and the value
of swelling degree of obtained crosslinked film showed that
glucomannan and kappa carrageenan was able to be cross-linked
using glutaraldehyde by film immersion and curing method without
catalyst. The cross-linked films were found to be pH sensitive,
indicating a potential to be used in drug delivery polymer system.
Abstract: Superabsorbent polymers received much attention and
are used in many fields because of their superior characters to
traditional absorbents, e.g., sponge and cotton. So, it is very
important but challenging to prepare highly and fast-swelling
superabsorbents. A reliable, efficient and low-cost technique for
removing heavy metal ions from wastewater is the adsorption using
bio-adsorbents obtained from biological materials, such as
polysaccharides-based hydrogels superabsorbents. In this study, novel multi-functional superabsorbent composites
type semi-interpenetrating polymer networks (Semi-IPNs) were
prepared via graft polymerization of acrylamide onto chitosan
backbone in presence of gelatin, CTS-g-PAAm/Ge, using potassium
persulfate and N,N’-methylene bisacrylamide as initiator and
crosslinker, respectively. These hydrogels were also partially
hydrolyzed to achieve superabsorbents with ampholytic properties
and uppermost swelling capacity. The formation of the grafted
network was evidenced by Fourier Transform Infrared Spectroscopy
(ATR-FTIR) and Thermogravimetric Analysis (TGA). The porous
structures were observed by Scanning Electron Microscope (SEM).
From TGA analysis, it was concluded that the incorporation of the Ge
in the CTS-g-PAAm network has marginally affected its thermal
stability. The effect of gelatin content on the swelling capacities of
these superabsorbent composites was examined in various media
(distilled water, saline and pH-solutions). The water absorbency was
enhanced by adding Ge in the network, where the optimum value was
reached at 2 wt. % of Ge. Their hydrolysis has not only greatly
optimized their absorption capacity but also improved the swelling
kinetic.These materials have also showed reswelling ability. We
believe that these super-absorbing materials would be very effective
for the adsorption of harmful metal ions from wastewater.
Abstract: Cell volume, together with membrane potential and
intracellular hydrogen ion concentration, is an essential biophysical
parameter for normal cellular activity. Cell volumes can be altered by
osmotically active compounds and extracellular tonicity.
In this study, a simple mathematical model of osmotically induced
cell swelling and shrinking is presented. Emphasis is given to water
diffusion across the membrane. The mathematical description of the
cellular behavior consists in a system of coupled ordinary differential
equations. We compare experimental data of cell volume alterations
driven by differences in osmotic pressure with mathematical
simulations under hypotonic and hypertonic conditions. Implications
for a future model are also discussed.
Abstract: The effect of the inclusion of thyme and rosemary
essential oils into chitosan films, as well as the microbiological and
physical properties when storing chitosan film with and without the
mentioned inclusion was studied. The film forming solution was
prepared by dissolving chitosan (2%, w/v), polysorbate 80 (4% w/w
CH) and glycerol (16% w/w CH) in aqueous lactic acid solutions
(control). The thyme (TEO) and rosemary (REO) essential oils (EOs)
were included 1:1 w/w (EOs:CH) on their combination 50/50
(TEO:REO). The films were stored at temperatures of 5, 20, 33°C
and a relative humidity of 75% during four weeks. The films with
essential oil inclusion did not show an antimicrobial activity against
strains. This behavior could be explained because the chitosan only
inhibits the growth of microorganisms in direct contact with the
active sites. However, the inhibition capacity of TEO was higher than
the REO and a synergic effect between TEO:REO was found for S.
enteritidis strains in the chitosan solution.
Some physical properties were modified by the inclusion of
essential oils. The addition of essential oils does not affect the
mechanical properties (tensile strength, elongation at break, puncture
deformation), the water solubility, the swelling index nor the DSC
behavior. However, the essential oil inclusion can significantly
decrease the thickness, the moisture content, and the L* value of
films whereas the b* value increased due to molecular interactions
between the polymeric matrix, the loosing of the structure, and the
chemical modifications. On the other hand, the temperature and time
of storage changed some physical properties on the chitosan films.
This could have occurred because of chemical changes, such as
swelling in the presence of high humidity air and the reacetylation of
amino groups. In the majority of cases, properties such as moisture
content, tensile strength, elongation at break, puncture deformation,
a*, b*, chrome, 7E increased whereas water resistance, swelling
index, L*, and hue angle decreased.
Abstract: Numerous amounts of metallurgical dusts and sludge containing iron as well as some other valuable elements such as Zn, Pb and C are annually produced in the steelmaking industry. These alternative iron ore resources (fines) with unsatisfying physical and metallurgical properties are difficult to recycle. However, agglomerating these fines to be further used as a feed stock for existing iron and steelmaking processes is practiced successfully at several plants but for limited extent.
In the present study, briquettes of integrated steelmaking industry waste materials (namely, BF-dust and sludge, BOF-dust and sludge) were used as feed stock to produce direct reduced iron (DRI). Physical and metallurgical properties of produced briquettes were investigated by means of TGA/DTA/QMS in combination with XRD. Swelling, softening and melting behavior were also studied using heating microscope.
Abstract: The behavior of model piles embedded in a very high expansive soil was investigated, a specially manufactured saturation-drying tank was used to apply three cycles of wetting and drying to the expansive soil surrounding the model straight shaft and under reamed piles, the relative movement of the piles with respect to the soil surface was recorded with time, also the exerted uplift pressure of the piles due to soil swelling was recorded. The behavior of unloaded straight shaft and under reamed piles was investigated. Two design charts were presented for straight shaft and under reamed piles one for the required pile depth for zero upward movement due to soil swelling, while the other for the required pile depth to exert zero uplift pressure when the soil swells. Under reamed piles showed a decrease in upward movement of 20% to 30%, and an uplift pressure decrease of 10% to 30%.
Abstract: Expansive soils swell when they absorb water and shrink when water evaporates from them. Hence, lightly loaded civil engineering structures founded in these soils are subjected to severe distress. Therefore, there is a need to ameliorate or improve these swelling soils through some innovative methods. This paper discusses chemical stabilisation of expansive soils, a technique in which chemical reagents such as lime and calcium chloride are added to expansive soils to reduce the volumetric changes occurring in expansive soils and to improve their engineering behaviour.
Abstract: The suitability of Newsprint and Kraft papers for the production of cement bonded ceiling board was investigated. Sample boards were produced from newsprint paper (100%), mixture of newsprint and Kraft paper (50:50) and Kraft paper (100%) at 1:1, 2:1 and 3:1 cement/paper mixing ratio respectively with 3% additive concentration of calcium chloride (CaCl2). Density, flexural and thickness swelling properties of the boards were investigated. The effects of paper type and mixing ratio on the physical and mechanical properties were also examined. The bending properties of the board which include Modulus of Elasticity (MOE) and Modulus of Rupture (MOR) increased linearly with increase in density. Modulus of rupture of boards increased as the density and mixing ratio increased. The thickness swelling property for the two paper types decreased as the board density and mixing ratio increased. Boards made from Kraft paper recorded higher strength values than the ones made from recycled newsprint paper while the mixture of kraft and newsprint papers had the best surface finish. The result of the study will help in managing the large quality of waste from paper converting/carton industry and that the ceiling boards produced could be installed with clout nails or used with suspended ceiling fittings.
Abstract: There is long history of konjac tubers being used as a cure for certain diseases in China and Japan. Konjac flour is prepared from konjac tubers and it contains high concentration of glucomannan. Konjac Glucomannan (KGM) is dietary fiber and the role of which has been demonstrated in weight reduction, lowering blood cholesterol and sugar level, promoting intestinal activity etc. Konjac glucomanan has a property of swelling by absorbing water, more than a hundred times its own weight. Therefore it helps increasing weight of feces, water content of feces, and promotes satiety feeling. Mode of actions of dietary fibre as laxatives agents includes holding water inside the bowel lumen, inhibition of water absorption in the colon and stimulating colonic motility. Number of fecal pellets did not effected in rats were fed on 300 and 600 mg/kg of konjac flour, as well as constipated control and Dulcolax treatment. Water content, weight of fecal pellets and gastrointestinal transit ratio were higher in rats treated with 600 mg/kg than 300 mg/kg of konjac flour. Rats were administered with Dulcolax showed the highest gastrointestinal transit ratio, followed by 600 mg/kg konjac flour. The lowest feed consumption was noted in 600 mg/kg konjac flour diet group.
Abstract: Chitosan is a derivative of chitin, a compound usually
isolated from the shells of some crustaceans such as crab, lobster and
shrimp. It has biocompatible, biodegradable, and antimicrobial
properties. To use these properties of chitosan in biomedical fields,
chitosan films (1%, 2%, 3% and 4%) were prepared by using l%
lactic acid as solvent. The effects of chitosan films on tensile
strength, elongation at break, degree of swelling, thickness,
morphology, allergic and irritation reactions and antibacterial
property were evaluated. Staphylococcus aureus and Escherichia coli
were used as tested microorganisms. In vivo wound healing activities
of chitosan films were investigated using mice model. As results,
Chitosan films have similar appearance and good swelling properties
and 4% chitosan film showed the better swelling activity and the
greatest elongation ratio than the other chitosan films. They also
showed their good activity of wound healing in mice model.
Moreover, the results showed that the films did not produce any
unwilling symptoms (allergy or irritation). In conclusion, it is evident
that the chitosan film has the potentiality to use as wound healing
biofilms in the biomedical fields.
Abstract: Preparation of hydrogel based on carrageenan
extracted from Kappaphycus alvarezii was conducted with film
immersion in glutaraldehyde solution (GA 4%w/w) for 2min and
then followed by thermal curing at 110°C for 25min. The method of
carrageenan recovery strongly determines the properties of
crosslinked carrageenan. Hydrogel obtained from alkali treated
carrageenan showed higher swelling ability compared to hydrogel
from nonalkali treated carrageenan. Hydrogel from alkali treated
showed the ability of sensitive to pH media.
Abstract: Hypericum perforatum L. is a member of the Hypericaceae (Guttiferae) family and commonly known as St. John’s wort. There is a growing interest in this medicinal plant because of the constituents of this genus. A number of species have been shown to possess various biological activities such as antiviral, wound healing, analgesic, hepatoprotective, antimicrobial and antioxidant activities and also have therapeutic effects on burns, bruises, swelling, anxiety and mild to moderate depression.
In this study, the aerial parts of Hypericum perforatum L. are extracted and the main and effective constituents are determined. The analysis of the extracts was performed by GC-MS and LC-MS. As a next step, it is aimed to investigate the usage of the main constituents of the medicinal plant.
Abstract: the effects of refining and alkaline chemicals on potential of recycling bleached chemical pulp of bagasse were investigated in this study. Recycling was done until three times. Handsheet properties such as, apparent density, light scattering coefficient, tear index, burst index, breaking length, and fold number according to TAPPI standard were measured. Water retention value also was used to considering the treatments during recycling. Refining enhanced the strength of recycled pulp by increasing fiber flexibility and swelling ability, whereas by applying chemical treatment didn't observe any improvement. The morphology of recycled fiber was considered with scanning electron microscopy (SEM).
Abstract: In this article, we synthesize a novel chitosan -based
superabsorbent hydrogel via graft copolymerization of mixtures
acrylic acid (AA) and N-vinyl pyrollidon onto chitosan backbones.
The polymerization reaction was carried out in an aqueous medium
and in the presence of ammonium persulfate (APS) as an initiator and
N,N'-methylene bisacrylamide (MBA) as a crosslinker.The hydrogel
structures were confirmed by FTIR spectroscopy. The swelling
behavior of these absorbent polymers was also investigated in
various salt solutions. Results indicated that the swelling capacity
decreased with an increase in the ionic strength of the swelling
medium. Furthermore, the swelling of superabsorbing hydrogels was
examined in solutions with pH values ranging between 1.0 and 13.0.
It showed a reversible pH-responsive behavior at pHs 2.0 and 8.0.
This on-off switching behavior makes the synthesized hydrogels as
an excellent candidate for controlled delivery of bioactive agents.
Abstract: This study investigated the effect of germination on chemical compositions, physio-chemical properties of malted (germinated) red sorghum flours and evaluated characteristics of gluten free breads from sorghum flour. Results showed that germinated sorghum flour had higher amylase activity, swelling power and solubility at 95°C, but lower in the peak, break down, final and set back viscosities than ungerminated sample (p≤0.05). Five gluten free breads made from sorghum flour blends, with different ratios of ungerminated and germinated sorghum flour, were compared for the physical properties with those made from wheat flour. Crumb hardness, cohesiveness, gumminess and chewiness of sorghum breads were found significantly higher than those of wheat bread. With increasing of ungerminated flour proportion, the bread hardness increased while the cohesiveness declined. Sorghum breads appeared red to human eyes with a*values of 10.41-15.77.Their crust and crumb colors differed significantly from those of wheat bread.
Abstract: Desert regions around the Nile valley in Upper Egypt
contain great extent of swelling soil. Many different comment
procedures of treatment of the swelling soils for construction such as
pre-swelling, load balance OR soil replacement. One of the measure
factors which affect the level of the aggressiveness of the swelling
soil is the direction of the infiltration water directions within the
swelling soils. In this paper a physical model was installed to
measure the effect of water on the swelling soil with replacement
using fatty acid distillation residuals (FADR) mixed with sand as
thick sand-FADR mixture to prevent the water pathway arrive to the
swelling soil. Testing program have been conducted on different
artificial samples with different sand to FADR contents ratios (4%,
6%, and 9%) to get the optimum value fulfilling the impermeable
replacement. The tests show that a FADR content of 9% is sufficient
to produce impermeable replacement.
Abstract: Chitosan is an attractive polysaccharide obtained by
deacetylation of an abundant natural biopolymer called chitin. Chitin
and chitosan are excellent materials. To improve the potential of
chitin and chitosan modification is needed. In the present study,
grafting of maleic acid on to chitosan by cerium ammonium nitrate in
acetic acid solution was investigated with use of a microwave and
reflux system. The grafted chitosan was characterized by using a
Fourier-transform infrared spectrometry. The solubility and swelling
behavior of grafted chitosans were determined in acetate buffer (pH
3.6), citrophosphate buffer (pH 5.6 and pH 7.0), and boric buffer (pH
9.2) solutions. The sample obtained by microwave system with use of
a chitosan/maleic anhydride/ceric ammonium nitrate 0.2/3.922/0.99
gram of raw material within 30 minute showed the maximum
swelling ratio (13.6) in boric buffer solution.
Abstract: This research was to evaluate a technical feasibility of
making single-layer experimental particleboard panels from bamboo
waste (Dendrocalamus asper Backer) by converting bamboo into
strips, which are used to make laminated bamboo furniture. Variable
factors were density (600, 700 and 800 kg/m3) and temperature of
condition (25, 40 and 55 °C). The experimental panels were tested for
their physical and mechanical properties including modulus of
elasticity (MOE), modulus of rupture (MOR), internal bonding
strength (IB), screw holding strength (SH) and thickness swelling
values according to the procedures defined by Japanese Industrial
Standard (JIS). The test result of mechanical properties showed that
the MOR, MOE and IB values were not in the set criteria, except the
MOR values at the density of 700 kg/m3 at 25 °C and at the density
of 800 kg/m3 at 25 and 40 °C, the IB values at the density of 600
kg/m3, at 40 °C, and at the density of 800 kg/m3 at 55 °C. The SH
values had the test result according to the set standard, except with
the density of 600 kg/m3, at 40 and 55 °C. Conclusively, a valuable
renewable biomass, bamboo waste could be used to manufacture
boards.
Abstract: In modern agriculture, polymeric hydrogels are
known as a component able to hold an amount of water due to their
3-dimensional network structure and their tendency to absorb water
in humid environments. In addition, these hydrogels are able to
controllably release the fertilisers and pesticides loaded in them.
Therefore, they deliver these materials to the plants' roots and help
them with growing. These hydrogels also reduce the pollution of
underground water sources by preventing the active components
from leaching. In this study, sIPN acrylamide based hydrogels are
synthesised by using acrylamide free radical, potassium acrylate, and
linear polyvinyl alcohol. Ammonium nitrate is loaded in the hydrogel
as the fertiliser. The effect of various amounts of monomers and
linear polymer, measured in molar ratio, on the swelling rate,
equilibrium swelling, and release of ammonium nitrate is studied.