Abstract: Nowadays there are several grid connected converter
in the grid system. These grid connected converters are generally the
converters of renewable energy sources, industrial four quadrant
drives and other converters with DC link. These converters are
connected to the grid through a three phase bridge. The standards
prescribe the maximal harmonic emission which could be easily
limited with high switching frequency. The increased switching
losses can be reduced to the half with the utilization of the wellknown
Flat-top modulation. The suggested control method is the
expansion of the Flat-top modulation with which the losses could be
also reduced to the half compared to the Flat-top modulation.
Comparing to traditional control these requirements can be
simultaneously satisfied much better with the DLF (DC Link
Floating) method.
Abstract: A hybrid Photovoltaic/Thermal (PV/T) solar system integrates photovoltaic and solar thermal technologies into one single solar energy device, with dual generation of electricity and heat energy. The aim of the present study is to evaluate the potential for introduction of the PV/T technology into Northern China. For this purpose, outdoor experiments were conducted on a prototype of a PV/T water-heating system. The annual thermal and electrical performances were investigated under the climatic conditions of Beijing. An economic analysis of the system was then carried out, followed by a sensitivity study. The analysis revealed that the hybrid system is not economically attractive with the current market and energy prices. However, considering the continuous commitment of the Chinese government towards policy development in the renewable energy sector, and technological improvements like the increasing cost-effectiveness of PV cells, PV/Thermal technology may become economically viable in the near future.
Abstract: Photovoltaic power generation forecasting is an
important task in renewable energy power system planning and
operating. This paper explores the application of neural networks
(NN) to study the design of photovoltaic power generation
forecasting systems for one week ahead using weather databases
include the global irradiance, and temperature of Ghardaia city
(south of Algeria) using a data acquisition system. Simulations were
run and the results are discussed showing that neural networks
Technique is capable to decrease the photovoltaic power generation
forecasting error.
Abstract: A ten-year grazing study was conducted at the
Agriculture and Agri-Food Canada Brandon Research Centre in
Manitoba to study the effect of alfalfa inclusion and fertilizer (N, P,
K, and S) addition on economics and efficiency of non-renewable
energy use in meadow brome grass-based pasture systems for beef
production. Fertilizing grass-only or alfalfa-grass pastures to full soil
test recommendations improved pasture productivity, but did not
improve profitability compared to unfertilized pastures. Fertilizing
grass-only pastures resulted in the highest net loss of any pasture
management strategy in this study. Adding alfalfa at the time of
seeding, with no added fertilizer, was economically the best pasture
improvement strategy in this study. Because of moisture limitations,
adding commercial fertilizer to full soil test recommendations is
probably not economically justifiable in most years, especially with
the rising cost of fertilizer. Improving grass-only pastures by adding
fertilizer and/or alfalfa required additional non-renewable energy
inputs; however, the additional energy required for unfertilized
alfalfa-grass pastures was minimal compared to the fertilized
pastures. Of the four pasture management strategies, adding alfalfa
to grass pastures without adding fertilizer had the highest efficiency
of energy use. Based on energy use and economic performance, the
unfertilized alfalfa-grass pasture was the most efficient and
sustainable pasture system.
Abstract: The paper presents the potential for RES in Romania
and the results of the Romanian national research project “Romania
contribution to the European targets regarding the development of
renewable energy sources - PROMES". The objective of the project
is the development of energy generation from renewable energy
sources (RES) in Romania by drawing up scenarios and prognosis
harmonized with national and European targets, RES development
effects modeling (environmental, economic, social etc.), research of
the impact of the penetration of RES into the main, implementation
of an advanced software system tool for RES information recording
and communication, experimental research based on demonstrative
applications.
The expected results are briefly presented, as well as the social,
economic and environmental impact.
Abstract: This paper presents the results of the authors in designing, experimenting, assessing and transferring an innovative approach to energy education in secondary schools, aimed to enhance the quality of learning in terms of didactic curricula and pedagogic methods. The training is online delivered to youngsters via e-Books and portals specially designed for this purpose or by learning by doing via interactive games. An online educational methodology is available teachers.
Abstract: The rapidly increasing costs of power line extensions
and fossil fuel, combined with the desire to reduce carbon dioxide
emissions pushed the development of hybrid power system suited for
remote locations, the purpose in mind being that of autonomous local
power systems. The paper presents the suggested solution for a “high
penetration" hybrid power system, it being determined by the
location of the settlement and its “zero policy" on carbon dioxide
emissions. The paper focuses on the technical solution and the power
flow management algorithm of the system, taking into consideration
local conditions of development.
Abstract: Renewable energy sources have gained ultimate urgency due to the need of the preservation of the environment for a sustainable development. Pyrolysis is an ultimate promising process in the recycling and acquisition of precious chemicals from wastes. Here, the co-pyrolysis of hazelnut shell with ultra-high molecular weight polyethylene was carried out catalytically and noncatalytically at 500 and 650 ºC. Potassium dichromate was added in certain amounts to act as a catalyst. The liquid, solid and gas products quantities were determined by gravimetry. As a main result, remarkable increases in gasification were observed by using this catalyst for pure components and their blends especially at 650 ºC. The increase in gas product quantity was compensated mainly with the decreases in the solid products and additionally in some cases liquid products quantities. These observations may stem from mainly the activation of carbon-carbon bonds rather than carbon-hydrogen bonds via potassium dichromate. Also, the catalytic effect of potassium dichromate on HS: PEO and HS: UHMWPE co-pyrolysis was compared.
Abstract: The increased use of biodiesel implies variations on both greenhouse gases and air pollutant emissions. Some studies point out that the use of biodiesel blends on diesel can help in controlling air pollution and promote a reduction of CO2 emissions. Reductions on PM, SO2, VOC and CO emissions are also expected, however NOx emissions may increase, which may potentiate O3 formation. This work aims to assess the impact of the biodiesel use on air quality, through a numerical modeling study, taking the Northern region of Portugal as a case study. The emission scenarios are focused on 2008 (baseline year) and 2020 (target year of Renewable Energy Directive-RED) and on three biodiesel blends (B0, B10 and B20). In a general way the use of biodiesel by 2020 will reduce the CO2 and air pollutants emissions in the Northern Portugal, improving air quality. However it will be in a very small extension.
Abstract: Sustainable energy usage has been recognized as one
of the important measure to increase the competitiveness of the
nation globally. Many strong emphases were given in the Ninth
Malaysia Plan (RMK9) to improve energy efficient especially to
government buildings. With this in view, a project to investigate the
potential of energy saving in selected building in Universiti Tun
Hussein Onn Malaysia (UTHM) was carried out. In this project, a
case study involving electric energy consumption of the academic
staff office building was conducted. The scope of the study include to
identify energy consumption in a selected building, to study energy
saving opportunities, to analyse cost investment in term of economic
and to identify users attitude with respect to energy usage. The
MS1525:2001, Malaysian Standard -Code of practice on energy
efficiency and use of renewable energy for non-residential buildings
was used as reference. Several energy efficient measures were
considered and their merits and priority were compared. Improving
human behavior can reduce energy consumption by 6% while
technical measure can reduce energy consumption by 44%. Two
economic analysis evaluation methods were applied; they are the
payback period method and net present value method.
Abstract: The world's population continues to grow at a quarter of a million people per day, increasing the consumption of energy. This has made the world to face the problem of energy crisis now days. In response to the energy crisis, the principles of renewable energy gained popularity. There are much advancement made in developing the wind and solar energy farms across the world. These energy farms are not enough to meet the energy requirement of world. This has attracted investors to procure new sources of energy to be substituted. Among these sources, extraction of energy from the waves is considered as best option. The world oceans contain enough energy to meet the requirement of world. Significant advancements in design and technology are being made to make waves as a continuous source of energy. One major hurdle in launching wave energy devices in a developing country like Pakistan is the initial cost. A simple, reliable and cost effective wave energy converter (WEC) is required to meet the nation-s energy need. This paper will present a novel design proposed by team SAS for harnessing wave energy. This paper has three major sections. The first section will give a brief and concise view of ocean wave creation, propagation and the energy carried by them. The second section will explain the designing of SAS-2. A gear chain mechanism is used for transferring the energy from the buoy to a rotary generator. The third section will explain the manufacturing of scaled down model for SAS-2 .Many modifications are made in the trouble shooting stage. The design of SAS-2 is simple and very less maintenance is required. SAS-2 is producing electricity at Clifton. The initial cost of SAS-2 is very low. This has proved SAS- 2 as one of the cost effective and reliable source of harnessing wave energy for developing countries.
Abstract: Since the European renewable energy directives set the
target for 22.1% of electricity generation to be supplied by 2010
[1], there has been increased interest in using green technologies
also within the urban enviroment. The most commonly considered
installations are solar thermal and solar photovoltaics. Nevertheless,
as observed by Bahaj et al. [2], small scale turbines can reduce the
built enviroment related CO2 emissions. Thus, in the last few years,
an increasing number of manufacturers have developed small wind
turbines specifically designed for the built enviroment. The present
work focuses on the integration into architectural systems of such
installations and presents a survey of successful case studies.
Abstract: As wind, solar and other clean and green energy
sources gain popularity worldwide, engineers are seeking ways to
make renewable energy systems more affordable and to integrate
them with existing ac power grids. In the present paper an attempt
has been made for integrating the PV arrays to the smart nano grid
using an artificial intelligent (AI) based solar powered cascade multilevel
inverter. The AI based controller switching scheme has been
used for improving the power quality by reducing the Total Harmonic
Distortion (THD) of the multi-level inverter output voltage.
Abstract: Recently, a growing interest has emerged on the
development of new and efficient energy sources, due to the inevitable extinction of the nonrenewable energy reserves. One of
these alternative sources which has a great potential and sustainability to meet up the energy demand is biomass energy. This
significant energy source can be utilized with various energy
conversion technologies, one of which is biomass gasification in
supercritical water.
Water, being the most important solvent in nature, has very important characteristics as a reaction solvent under supercritical
circumstances. At temperatures above its critical point (374.8oC and
22.1 MPa), water becomes more acidic and its diffusivity increases.
Working with water at high temperatures increases the thermal
reaction rate, which in consequence leads to a better dissolving of the
organic matters and a fast reaction with oxygen. Hence, supercritical water offers a control mechanism depending on solubility, excellent
transport properties based on its high diffusion ability and new reaction possibilities for hydrolysis or oxidation.
In this study the gasification of a real biomass, namely olive mill
wastewater (OMW), in supercritical water is investigated with the
use of Pt/Al2O3 and Ni/Al2O3 catalysts. OMW is a by-product
obtained during olive oil production, which has a complex nature
characterized by a high content of organic compounds and
polyphenols. These properties impose OMW a significant pollution
potential, but at the same time, the high content of organics makes
OMW a desirable biomass candidate for energy production.
All of the catalytic gasification experiments were made with five
different reaction temperatures (400, 450, 500, 550 and 600°C),
under a constant pressure of 25 MPa. For the experiments conducted
with Ni/Al2O3 catalyst, the effect of five reaction times (30, 60, 90,
120 and 150 s) was investigated. However, procuring that similar
gasification efficiencies could be obtained at shorter times, the experiments were made by using different reaction times (10, 15, 20,
25 and 30 s) for the case of Pt/Al2O3 catalyst. Through these experiments, the effects of temperature, time and catalyst type on the
gasification yields and treatment efficiencies were investigated.
Abstract: There is a great deal of interest in constructing Double Skin Facade (DSF) structures which are considered as modern movement in field of Energy Conservation, renewable energies, and Architecture design. This trend provides many conclusive alternatives which are frequently associated with sustainable building. In this paper a building with Double Skin Facade is considered in the semiarid climate of Tehran, Iran, in order to consider the DSF-s performance during hot seasons. Mathematical formulations calculate solar heat gain by the external skin. Moreover, Computational Fluid Dynamics (CFD) simulations were performed on the case study building to enhance effectiveness of the facade. The conclusion divulged difference of gained energy by the cavity and room with and without blind and louvers. Some solutions were introduced to surge the performance of natural ventilation by plunging the cooling loads in summer.
Abstract: Solar energy has a major role in renewable energy
resources. Solar Cell as a basement of solar system has attracted lots
of research. To conduct a study about solar energy system, an
authenticated model is required. Diode base PV models are widely
used by researchers. These models are classified based on the number
of diodes used in them. Single and two-diode models are well
studied. Single-diode models may have two, three or four elements.
In this study, these solar cell models are examined and the simulation
results are compared to each other. All PV models are re-designed in
the Matlab/Simulink software and they examined by certain test
conditions and parameters. This paper provides comparative studies
of these models and it tries to compare the simulation results with
manufacturer-s data sheet to investigate model validity and accuracy.
The results show a four- element single-diode model is accurate and
has moderate complexity in contrast to the two-diode model with
higher complexity and accuracy
Abstract: The objective of this research is to study the technical
and economic performance of wind/diesel/battery (W/D/B) system
supplying a remote small gathering of six families using HOMER
software package. The electrical energy is to cater for the basic needs
for which the daily load pattern is estimated. Net Present Cost (NPC)
and Cost of Energy (COE) are used as economic criteria, while the measure of performance is % of power shortage. Technical and
economic parameters are defined to estimate the feasibility of the
system under study. Optimum system configurations are estimated for two sites. Using HOMER software, the simulation results showed that W/D/B systems are economical for the assumed community sites
as the price of generated electricity is about 0.308 $/kWh, without
taking external benefits into considerations. W/D/B systems are more
economical than W/B or diesel alone systems, as the COE is 0.86 $/kWh for W/B and 0.357 $/kWh for diesel alone.
Abstract: The development of renewable energies - particularly energy from wind, water, solar power and biomass - is a central aim of the European Commission's energy policy. There are several reasons for this choice: renewable energies are sustainable, nonpolluting, widely available and clean. Increasing the share of renewable energy in the energy balance enhances sustainability. It also helps to improve the security of energy supply by reducing the Community's growing dependence on imported energy sources.In this paper it was studied the possibility to realize three photovoltaic systems in the Italian Natural Park “Gola della Rossa e di Frasassi". The first photovoltaic system is a grid-connected system for Services and Documentation Center of Castelletta with a nominal power of about 6 kWp. The second photovoltaic system is a grid-connected integrated system on the ticket office-s roof with a nominal power of about 4 kWp. The third project is set up by five grid-connected systems integrated on the roofs of the bungalows in Natural Park-s tourist camping with a nominal power of about 10 kWp. The electricity which is generated by all these plants is purchased according to the Italian program called “Conto Energia". Economical analysis and the amount of the avoided CO2 emissions are elaborated for these photovoltaic systems.
Abstract: Since the 80s huge efforts have been made to utilize
renewable energy sources to generate electric power. This paper
reports some aspects of integration of the distributed generators into
the low voltage distribution networks. An assessment of impact of the
distributed generators on the reliability indices of low voltage
network is performed. Results obtained from case study using low
voltage network, are presented and discussed.
Abstract: The utilization of renewable energy sources in electric
power systems is increasing quickly because of public apprehensions
for unpleasant environmental impacts and increase in the energy
costs involved with the use of conventional energy sources. Despite
the application of these energy sources can considerably diminish the
system fuel costs, they can also have significant influence on the
system reliability. Therefore an appropriate combination of the
system reliability indices level and capital investment costs of system
is vital. This paper presents a hybrid wind/photovoltaic plant, with
the aim of supplying IEEE reliability test system load pattern while
the plant capital investment costs is minimized by applying a hybrid
particle swarm optimization (PSO) / harmony search (HS) approach,
and the system fulfills the appropriate level of reliability.