Abstract: Sedimentation process resulting from soil erosion in
the water basin especially in arid and semi-arid where poor
vegetation cover in the slope of the mountains upstream could
contribute to sediment formation. The consequence of sedimentation
not only makes considerable change in the morphology of the river
and the hydraulic characteristics but would also have a major
challenge for the operation and maintenance of the canal network
which depend on water flow to meet the stakeholder-s requirements.
For this reason mathematical modeling can be used to simulate the
effective factors on scouring, sediment transport and their settling
along the waterways. This is particularly important behind the
reservoirs which enable the operators to estimate the useful life of
these hydraulic structures. The aim of this paper is to simulate the
sedimentation and erosion in the eastern and western water intake
structures of the Dez Diversion weir using GSTARS-3 software. This
is done to estimate the sedimentation and investigate the ways in
which to optimize the process and minimize the operational
problems. Results indicated that the at the furthest point upstream of
the diversion weir, the coarser sediment grains tended to settle. The
reason for this is the construction of the phantom bridge and the
outstanding rocks just upstream of the structure. The construction of
these along the river course has reduced the momentum energy
require to push the sediment loads and make it possible for them to
settle wherever the river regime allows it. Results further indicated a
trend for the sediment size in such a way that as the focus of study
shifts downstream the size of grains get smaller and vice versa. It
was also found that the finding of the GSTARS-3 had a close
proximity with the sets of the observed data. This suggests that the
software is a powerful analytical tool which can be applied in the
river engineering project with a minimum of costs and relatively
accurate results.
Abstract: In this paper the application of rule mining in order to
review the effective factors on supplier selection is reviewed in the
following three sections 1) criteria selecting and information
gathering 2) performing association rule mining 3) validation and
constituting rule base. Afterwards a few of applications of rule base
is explained. Then, a numerical example is presented and analyzed
by Clementine software. Some of extracted rules as well as the
results are presented at the end.
Abstract: In the gas refineries of Iran-s South Pars Gas
Complex, Sulfrex demercaptanization process is used to remove
volatile and corrosive mercaptans from liquefied petroleum gases by
caustic solution. This process consists of two steps. Removing low
molecular weight mercaptans and regeneration exhaust caustic. Some
parameters such as LPG feed temperature, caustic concentration and
feed-s mercaptan in extraction step and sodium mercaptide content in
caustic, catalyst concentration, caustic temperature, air injection rate
in regeneration step are effective factors. In this paper was focused on
temperature factor that play key role in mercaptans extraction and
caustic regeneration. The experimental results demonstrated by
optimization of temperature, sodium mercaptide content in caustic
because of good oxidation minimized and sulfur impurities in
product reduced.
Abstract: Monitored 3-Dimensional (3D) video experience can be utilized as “feedback information” to fine tune the service parameters for providing a better service to the demanding 3D service customers. The 3D video experience which includes both video quality and depth perception is influenced by several contextual and content related factors (e.g., ambient illumination condition, content characteristics, etc) due to the complex nature of the 3D video. Therefore, effective factors on this experience should be utilized while assessing it. In this paper, structural information of the depth map sequences of the 3D video is considered as content related factor effective on the depth perception assessment. Cartoon-like filter is utilized to abstract the significant depth levels in the depth map sequences to determine the structural information. Moreover, subjective experiments are conducted using 3D videos associated with cartoon-like depth map sequences to investigate the effectiveness of ambient illumination condition, which is a contextual factor, on depth perception. Using the knowledge gained through this study, 3D video experience metrics can be developed to deliver better service to the 3D video service users.
Abstract: Today, incorrect use of lands and land use changes,
excessive grazing, no suitable using of agricultural farms, plowing on
steep slopes, road construct, building construct, mine excavation etc
have been caused increasing of soil erosion and sediment yield. For
erosion and sediment estimation one can use statistical and empirical
methods. This needs to identify land unit map and the map of
effective factors. However, these empirical methods are usually time
consuming and do not give accurate estimation of erosion. In this
study, we applied GIS techniques to estimate erosion and sediment of
Menderjan watershed at upstream Zayandehrud river in center of
Iran. Erosion faces at each land unit were defined on the basis of land
use, geology and land unit map using GIS. The UTM coordinates of
each erosion type that showed more erosion amounts such as rills and
gullies were inserted in GIS using GPS data. The frequency of
erosion indicators at each land unit, land use and their sediment yield
of these indices were calculated. Also using tendency analysis of
sediment yield changes in watershed outlet (Menderjan hydrometric
gauge station), was calculated related parameters and estimation
errors. The results of this study according to implemented watershed
management projects can be used for more rapid and more accurate
estimation of erosion than traditional methods. These results can also
be used for regional erosion assessment and can be used for remote
sensing image processing.
Abstract: The objective of this research is parameters optimized
of the stair shape workpiece which is cut by CNC Wire-Cut EDM
(WEDW). The experiment material is SKD-11 steel of stair-shaped
with variable height workpiece 10, 20, 30 and 40 mm. with the same
10 mm. thickness are cut by Sodick's CNC Wire-Cut EDM model
AD325L.
The experiments are designed by 3k full factorial experimental
design at 3 level 2 factors and 9 experiments with 2 replicate. The
selected two factor are servo voltage (SV) and servo feed rate (SF)
and the response is cutting thickness error. The experiment is divided
in two experiments. The first experiment determines the significant
effective factor at confidential interval 95%. The SV factor is the
significant effective factor from first result. In order to result smallest
cutting thickness error of workpieces is 17 micron with the SV value
is 46 volt. Also show that the lower SV value, the smaller different
thickness error of workpiece. Then the second experiment is done to
reduce different cutting thickness error of workpiece as small as
possible by lower SV. The second experiment result show the
significant effective factor at confidential interval 95% is the SV
factor and the smallest cutting thickness error of workpieces reduce
to 11 micron with the experiment SV value is 36 volt.
Abstract: A passive system "Qanat" is collection of some
underground wells. A mother-well was dug in a place far from the
city where they could reach to the water table maybe 100 meters
underground, they dug other wells to direct water toward the city,
with minimum possible gradient. Using the slope of the earth they
could bring water close to the surface in the city. The source of water
or the appearance of Qanat, land slope and the ownership lines are
the important and effective factors in the formation of routes and the
segment division of lands to the extent that making use of Qanat as
the techniques of extracting underground waters creates a channel of
routes with an organic order and hierarchy coinciding the slope of
land and it also guides the Qanat waters in the tradition texture of salt
desert and border provinces of it. Qanats are excavated in a specified
distinction from each other. The quantity of water provided by
Qanats depends on the kind of land, distance from mountain,
geographical situation of them and the rate of water supply from the
underground land. The rate of underground waters, possibility of
Qanat excavation, number of Qanats and rate of their water supply
from one hand and the quantity of cultivable fertile lands from the
other hand are the important natural factors making the size of cities.
In the same manner the cities with several Qanats have multi central
textures. The location of cities is in direct relation with land quality,
soil fertility and possibility of using underground water by excavating
Qanats. Observing the allowable distance for Qanat watering is a
determining factor for distance between villages and cities.
Topography, land slope, soil quality, watering system, ownership,
kind of cultivation, etc. are the effective factors in directing Qanats
for excavation and guiding water toward the cultivable lands and it
also causes the formation of different textures in land division of
farming provinces. Several divisions such as orderly and wide, inorderly,
thin and long, comb like, etc. are the introduction to organic
order. And at the same time they are complete coincidence with
environmental conditions in the typical development of ecological
architecture and planning in the traditional cities and settlements
order.
Abstract: Over half of the total electricity consumption is used in buildings. Air-conditioning and electric lighting are the two main resources of electricity consumption in high rise buildings. One way to reduce electricity consumption would be to limit heat gain into buildings, therefore reduce the demand for air-conditioning during hot summer months especially in hot regions. On the other hand natural daylight can be used to reduce the use of electricity for artificial lighting. In this paper effective factors on minimizing heat gain and achieving required day light were reviewed .As daylight always accompanied by solar heat gain. Also interactions between heat gain and daylight were discussed through previous studies and equations which are related to heat gain and day lighting especially in high rise buildings. As a result importance of building-s form and its component on energy consumption in buildings were clarified.
Abstract: The main objective of seismic rehabilitation in the
foundations is decreasing the range of horizontal and vertical
vibrations and omitting high frequencies contents under the seismic
loading. In this regard, the advantages of micropiles network is
utilized. Reduction in vibration range of foundation can be achieved
by using high dynamic rigidness module such as deep foundations. In
addition, natural frequency of pile and soil system increases in regard
to rising of system rigidness. Accordingly, the main strategy is
decreasing of horizontal and vertical seismic vibrations of the
structure. In this case, considering the impact of foundation, pile and
improved soil foundation is a primary concern. Therefore, in this
paper, effective factors are studied on the seismic rehabilitation of
foundations applying network micropiles in sandy soils with
nonlinear reaction.
Abstract: This paper examines the interplay of policy options
and cost-effective technology in providing sustainable distance
education. A case study has been conducted among the learners and
teachers. The emergence of learning technologies through CD,
internet, and mobile is increasingly adopted by distance institutes for
quick delivery and cost-effective factors. Their sustainability is
conditioned by the structure of learners and well as the teaching
community. The structure of learners in terms of rural and urban
background revealed similarity in adoption and utilization of mobile
learning. In other words, the technology transcended the rural-urban
dichotomy. The teaching community was divided into two groups on
policy issues. This study revealed both cost-effective as well as
sustainability impacts on different learners groups divided by rural
and urban location.
Abstract: In this work, several ASP solutions were flooded into
fractured models initially saturated with heavy oil at a constant flow
rate and different geometrical characteristics of fracture. The ASP
solutions are constituted from 2 polymers i.e. a synthetic polymer,
hydrolyzed polyacrylamide as well as a biopolymer, a surfactant and
2types of alkaline. The results showed that using synthetic
hydrolyzed polyacrylamide polymer increases ultimate oil recovery;
however, type of alkaline does not play a significant rule on oil
recovery. In addition, position of the injection well respect to the
fracture system has remarkable effects on ASP flooding. For instance
increasing angle of fractures with mean flow direction causes more
oil recovery and delays breakthrough time. This work can be
accounted as a comprehensive survey on ASP flooding which
considers most of effective factors in this chemical EOR method.
Abstract: Sediment formation and its transport along the river course is considered as important hydraulic consideration in river engineering. Their impact on the morphology of rivers on one hand and important considerations of which in the design and construction of the hydraulic structures on the other has attracted the attention of experts in arid and semi-arid regions. Under certain conditions where the momentum energy of the flow stream reaches a specific rate, the sediment materials start to be transported with the flow. This can usually be analyzed in two different categories of suspended and bed load materials. Sedimentation phenomenon along the waterways and the conveyance of vast volume of materials into the canal networks can potentially influence water abstraction in the intake structures. This can pose a serious threat to operational sustainability and water delivery performance in the canal networks. The situation is serious where ineffective watershed management (poor vegetation cover in the water basin) is the underlying cause of soil erosion which feeds the materials into the waterways that intern would necessitate comprehensive study. The present paper aims to present an analytical investigation of the sediment process in the waterways on one hand and estimation of the sediment load transport into the lined canals using the SHARC software on the other. For this reason, the paper focuses on the comparative analysis of the hydraulic behaviors of the Sabilli main canal that feeds the pumping station with that of the Western canal in the Greater Dezful region to identify effective factors in sedimentation and ways of mitigating their impact on water abstraction in the canal systems. The method involved use of observational data available in the Dezful Dastmashoon hydrometric station along a 6 km waterway of the Sabilli main canal using the SHARC software to estimate the suspended load concentration and bed load materials. Results showed the transport of a significant volume of sediment loads from the waterways into the canal system which is assumed to have arisen from the absence of stilling basin on one hand and the gravity flow on the other has caused serious challenges. This is contrary to what occurs in the Sabilli canal, where the design feature which incorporates a settling basin just before the pumping station is the major cause of reduced sediment load transport into the canal system.Results showed that modification of the present design features by constructing a settling basin just upstream of the western intake structure can considerably reduce the entry of sediment materials into the canal system. Not only this can result in the sustainability of the hydraulic structures but can also improve operational performance of water conveyance and distribution system, all of which are the pre-requisite to secure reliable and equitable water delivery regime for the command area.
Abstract: The high temperature degree and uniform
Temperature Distribution (TD) on surface of cookware which contact
with food are effective factors for improving cookware application.
Additionally, the ability of pan material in retaining the heat and nonreactivity
with foods are other significant properties. It is difficult for
single material to meet a wide variety of demands such as superior
thermal and chemical properties. Multi-Layer Plate (MLP) makes
more regular TD. In this study the main objectives are to find the best
structure (single or multi-layer) and materials to provide maximum
temperature degree and uniform TD up side surface of pan. And also
heat retaining of used metals with goal of improving the thermal
quality of pan to economize the energy. To achieve this aim were
employed Finite Element Method (FEM) for analyzing transient
thermal behavior of applied materials. The analysis has been
extended for different metals, we achieved the best temperature
profile and heat retaining in Copper/ Stainless Steel MLP.
Abstract: The great challenge of the agricultural sector is to
produce more crop from less water, which can be achieved by
increasing crop water productivity. The modernization of the
irrigation systems offers a number of possibilities to expand the
economic productivity of water and improve the virtual water status.
The objective of the present study is to assess the global water
productivity (GWP) within the major irrigation command areas of
I.R. Iran. For this purpose, fourteen irrigation command areas where
located in different areas of Iran were selected. In order to calculate
the global water productivity of irrigation command areas, all data on
the delivered water to cropping pattern, cultivated area, crops water
requirement, and yield production rate during 2002-2006 were
gathered. In each of the command areas it seems that the cultivated
crops have a higher amount of virtual water and thus can be replaced
by crops with less virtual water. This is merely suggested due to crop
water consumption and at the time of replacing crops, economic
value as well as cultural and political factors must be considered. The
results indicated that the lowest GWP belongs to Mahyar and
Borkhar irrigation areas, 0.24 kg m-3, and the highest is that of the
Dez irrigation area, 0.81 kg m-3. The findings demonstrated that
water management in the two irrigation areas is just efficient. The
difference in the GWP of irrigation areas is due to variations in the
cropping pattern, amount of crop productions, in addition to the
effective factors in the water use efficiency in the irrigation areas.
Abstract: Droughts are complex, natural hazards that, to a
varying degree, affect some parts of the world every year. The range
of drought impacts is related to drought occurring in different stages
of the hydrological cycle and usually different types of droughts,
such as meteorological, agricultural, hydrological, and socioeconomical
are distinguished. Streamflow drought was analyzed by
the method of truncation level (at 70% level) on daily discharges
measured in 54 hydrometric stations in southwestern Iran. Frequency
analysis was carried out for annual maximum series (AMS) of
drought deficit volume and duration series. Some factors including
physiographic, climatic, geologic, and vegetation cover were studied
as influential factors in the regional analysis. According to the results
of factor analysis, six most effective factors were identified as area,
rainfall from December to February, the percent of area with
Normalized Difference Vegetation Index (NDVI)