Abstract: Multigrade bitumen asphalt is a quality asphalt product that is not utilised in many places globally. Multigrade bitumen is believed to be less sensitive to temperature, which gives it an advantage over conventional binders. Previous testing has shown that asphalt temperature changes greatly with depth, but currently the industry standard is to nominate a single temperature for design. For detailed design of asphalt roads, perhaps asphalt layers should be divided into nominal layer depths and different modulus and fatigue equations/values should be used to reflect the temperatures of each respective layer. A collaboration of previous laboratory testing conducted on multigrade bitumen asphalt beams under a range of temperatures and loading conditions was analysed. The samples tested included 0% or 15% recycled asphalt pavement (RAP) to determine what impact the recycled material has on the fatigue life and stiffness of the pavement. This paper investigated the temperature susceptibility of multigrade bitumen asphalt pavements compared to conventional binders by combining previous testing that included conducting a sweep of fatigue tests, developing complex modulus master curves for each mix and a study on how pavement temperature changes through pavement depth. This investigation found that the final design of the pavement is greatly affected by the nominated pavement temperature and respective material properties. This paper has outlined a potential revision to the current design approach for asphalt pavements and proposes that further investigation is needed into pavement temperature and its incorporation into design.
Abstract: Bitumen is one of the most applicable materials in pavement engineering. It is a binding material with unique viscoelastic properties, especially when it mixes with polymer. In this study, to figure out the viscoelastic behaviour of the polymer modified with bitumen (PMB), a series of dynamic shearing rheological (DSR) tests were conducted. Four percentages of lime (i.e. 1%, 2%, 4% and 5%) were mixed with PMB and tested under four different temperatures including 64ºC, 70ºC, 76ºC and 82ºC. The results indicated that complex shearing modulus (G*) increased by increasing the frequency due to raised resistance against deformation. The phase angle (δ) showed a decreasing trend by incrementing the frequency. The addition of lime percentages increased the complex modulus value and declined phase angle parameter. Increasing the temperature decreased the complex modulus and increased the phase angle until 70ºC. The decreasing trend of rutting factor with increasing temperature revealed that rutting factor improved by the addition of the lime to the PMB.
Abstract: This study investigated the influence of Cloisite-15A nanoclay on the physical, performance, and mechanical properties of bitumen binder. Cloisite-15A was blended in the bitumen in variegated percentages from 1% to 9% with increment of 2%. The blended bitumen was characterized using penetration, softening point, and dynamic viscosity using rotational viscometer, and compared with unmodified bitumen equally penetration grade 60/70. The rheological parameters were investigated using Dynamic Shear Rheometer (DSR), and mechanical properties were investigated by using Marshall Stability test. The results indicated an increase in softening point, dynamic viscosity and decrease in binder penetration. Rheological properties of bitumen increase complex modulus, decrease phase angle and improve rutting resistances as well. There was significant improvement in Marshall Stability, rather marginal improvement in flow value. The best improvement in the modified binder was obtained with 5% Cloisite-15A nanoclay.
Abstract: This paper deals with nonlinear vibration analysis
using finite element method for frame structures consisting of elastic
and viscoelastic damping layers supported by multiple nonlinear
concentrated springs with hysteresis damping. The frame is supported
by four nonlinear concentrated springs near the four corners. The
restoring forces of the springs have cubic non-linearity and linear
component of the nonlinear springs has complex quantity to represent
linear hysteresis damping. The damping layer of the frame structures
has complex modulus of elasticity. Further, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled differential equations using normal coordinate corresponding
to linear natural modes. Comparing shares of strain energy of the
elastic frame, the damping layer and the springs, we evaluate the
influences of the damping couplings on the linear and nonlinear impact
responses. We also investigate influences of damping changed by
stiffness of the elastic frame on the nonlinear coupling in the damped
impact responses.
Abstract: A numerical method is proposed to calculate damping
properties for sound-proof structures involving elastic body,
viscoelastic body, and porous media. For elastic and viscoelastic body
displacement is modeled using conventional finite elements including
complex modulus of elasticity. Both effective density and bulk
modulus have complex quantities to represent damped sound fields in
the porous media. Particle displacement in the porous media is
discretised using finite element method. Displacement vectors as
common unknown variables are solved under coupled condition
between elastic body, viscoelastic body and porous media. Further,
explicit expressions of modal loss factor for the mixed structures are
derived using asymptotic method. Eigenvalue analysis and frequency
responded were calculated for automotive test panel laminated
viscoelastic and porous structures using this technique, the results
almost agreed with the experimental results.
Abstract: The dynamic or complex modulus test is considered
to be a mechanistically based laboratory test to reliably characterize
the strength and load-resistance of Hot-Mix Asphalt (HMA) mixes
used in the construction of roads. The most common observation is
that the data collected from these tests are often noisy and somewhat
non-sinusoidal. This hampers accurate analysis of the data to obtain
engineering insight. The goal of the work presented in this paper is to
develop and compare automated evolutionary computational
techniques to filter test noise in the collection of data for the HMA
complex modulus test. The results showed that the Covariance
Matrix Adaptation-Evolutionary Strategy (CMA-ES) approach is
computationally efficient for filtering data obtained from the HMA
complex modulus test.