Abstract: The propagation of microwave is affected by rain and dust particles causing signal attenuation and de-polarization. Computations of these effects require knowledge of the propagation characteristics of microwave and millimeter wave energy in the climate conditions of the studied region. This paper presents effect of wind and humidity on wireless communication such as microwave links in the North West region of Libya (Al-Khoms). The experimental procedure is done on three selected antennae towers (Nagaza station, Al-Khoms center station, Al-Khoms gateway station) for determining the attenuation loss per unit length and cross-polarization discrimination (XPD) change. Dust particles are collected along the region of the study, to measure the particle size distribution (PSD), calculate the concentration, and chemically analyze the contents, then the dielectric constant can be calculated. The results show that humidity and dust, antenna height and the visibility affect both attenuation and phase shift; in which, a few considerations must be taken into account in the communication power budget.
Abstract: Local generated and distributed system for thermal and electrical energy is sighted in the near future to reduce transmission losses instead of the centralized system. Distributed Energy Resources (DER) is designed at different sizes (small and medium) and it is incorporated in energy distribution between the hubs. The energy generated from each technology at each hub should meet the local energy demands. Economic and environmental enhancement can be achieved when there are interaction and energy exchange between the hubs. Network energy system and CO2 optimization between different six hubs presented Canadian community level are investigated in this study. Three different scenarios of technology systems are studied to meet both thermal and electrical demand loads for the six hubs. The conventional system is used as the first technology system and a reference case study. The conventional system includes boiler to provide the thermal energy, but the electrical energy is imported from the utility grid. The second technology system includes combined heat and power (CHP) system to meet the thermal demand loads and part of the electrical demand load. The third scenario has integration systems of CHP and Organic Rankine Cycle (ORC) where the thermal waste energy from the CHP system is used by ORC to generate electricity. General Algebraic Modeling System (GAMS) is used to model DER system optimization based on energy economics and CO2 emission analyses. The results are compared with the conventional energy system. The results show that scenarios 2 and 3 provide an annual total cost saving of 21.3% and 32.3 %, respectively compared to the conventional system (scenario 1). Additionally, Scenario 3 (CHP & ORC systems) provides 32.5% saving in CO2 emission compared to conventional system subsequent case 2 (CHP system) with a value of 9.3%.
Abstract: In this paper, CYME Distribution software has been used to assess the impacts of solar Photovoltaic (PV) distributed generation (DG) plant on the Electricity Company of Ghana (ECG) 33 kV sub-transmission network at different PV penetration levels. As ECG begins to encourage DG PV interconnections within its network, there has been the need to assess the impacts on the sub-transmission losses and voltage contribution. In Tema, a city in Accra - Ghana, ECG has a 33 kV sub-transmission network made up of 20 No. 33 kV buses that was modeled. Three different locations were chosen: The source bus, a bus along the sub-transmission radial network and a bus at the tail end to determine the optimal location for DG PV interconnection. The optimal location was determined based on sub-transmission technical losses and voltage impact. PV capacities at different penetration levels were modeled at each location and simulations performed to determine the optimal PV penetration level. Interconnection at a bus along (or in the middle of) the sub-transmission network offered the highest benefits at an optimal PV penetration level of 80%. At that location, the maximum voltage improvement of 0.789% on the neighboring 33 kV buses and maximum loss reduction of 6.033% over the base case scenario were recorded. Hence, the optimal location for DG PV integration within the 33 kV sub-transmission utility network is at a bus along the sub-transmission radial network.
Abstract: Sound attenuation in absorptive silencers has been analyzed in this paper. The structure of such devices is as follows. When the rigid duct of an expansion chamber has been lined by a packed absorptive material under a perforated membrane, incident sound waves will be dissipated by the absorptive liners. This kind of silencer, usually are applicable for medium to high frequency ranges. Several conditions for different absorptive materials, variety in their thicknesses, and different shapes of the expansion chambers have been studied in this paper. Also, graphs of sound attenuation have been compared between empty expansion chamber and duct of silencer with applying liner. Plane waves have been assumed in inlet and outlet regions of the silencer. Presented results that have been achieved by applying finite element method (FEM), have shown the dependence of the sound attenuation spectrum to flow resistivity and the thicknesses of the absorptive materials, and geometries of the cross section (configuration of the silencer). As flow resistivity and thickness of absorptive materials increase, sound attenuation improves. In this paper, diagrams of the transmission loss (TL) for absorptive silencers in five different cross sections (rectangle, circle, ellipse, square, and rounded rectangle as the main geometry) have been presented. Also, TL graphs for silencers using different absorptive material (glass wool, wood fiber, and kind of spongy materials) as liner with three different thicknesses of 5 mm, 15 mm, and 30 mm for glass wool liner have been exhibited. At first, the effect of substances of the absorptive materials with the specific flow resistivity and densities on the TL spectrum, then the effect of the thicknesses of the glass wool, and at last the efficacy of the shape of the cross section of the silencer have been investigated.
Abstract: In this paper, we demonstrated a 1 × 4 silicon photonic cascaded arrayed waveguide grating, which is fabricated on a SOI wafer with a 220 nm top Si layer and a 2µm buried oxide layer. The measured on-chip transmission loss of this cascaded arrayed waveguide grating is ~ 5.6 dB, including the fiber-to-waveguide coupling loss. The adjacent crosstalk is 33.2 dB. Compared to the normal single silicon photonic arrayed waveguide grating with a crosstalk of ~ 12.5 dB, the crosstalk of this device has been dramatically increased.
Abstract: In this paper, the specific sound Transmission Loss
(TL) of the Laminated Composite Plate (LCP) with different material
properties in each layer is investigated. The numerical method to
obtain the TL of the LCP is proposed by using elastic plate theory. The
transfer matrix approach is novelty presented for computational
efficiency in solving the numerous layers of dynamic stiffness matrix
(D-matrix) of the LCP. Besides the numerical simulations for
calculating the TL of the LCP, the material properties inverse method
is presented for the design of a laminated composite plate analogous to
a metallic plate with a specified TL. As a result, it demonstrates that
the proposed computational algorithm exhibits high efficiency with a
small number of iterations for achieving the goal. This method can be
effectively employed to design and develop tailor-made materials for
various applications.
Abstract: Restructuring of Electricity supply industry introduced many issues such as transmission pricing, transmission loss allocation and congestion management. Many methodologies and algorithms were proposed for addressing these issues. In this paper a power flow tracing based method is proposed which involves Matrices methodology for the transmission usage and loss allocation for generators and demands. This method provides loss allocation in a direct way because all the computation is previously done for usage allocation. The proposed method is simple and easy to implement in a large power system. Further it is less computational because it requires matrix inversion only a single time. After usage and loss allocation cooperative game theory is applied to results for finding efficient economic signals. Nucleolus and Shapely value approach is used for optimal allocation of results. Results are shown for the IEEE 6 bus system and IEEE 14 bus system.
Abstract: Economic Dispatch is one of the most important power system management tools. It is used to allocate an amount of power generation to the generating units to meet the load demand. The Economic Dispatch problem is a large scale nonlinear constrained optimization problem. In general, heuristic optimization techniques are used to solve non-convex Economic Dispatch problem. In this paper, ideas from Reinforcement Learning are proposed to solve the non-convex Economic Dispatch problem. Q-Learning is a reinforcement learning techniques where each generating unit learn the optimal schedule of the generated power that minimizes the generation cost function. The eligibility traces are used to speed up the Q-Learning process. Q-Learning with eligibility traces is used to solve Economic Dispatch problems with valve point loading effect, multiple fuel options, and power transmission losses.
Abstract: One of the major problems in liberalized power
markets is loss allocation. In this paper, a different method for
allocating transmission losses to pool market participants is
proposed. The proposed method is fundamentally based on
decomposition of loss function and current projection concept. The
method has been implemented and tested on several networks and
one sample summarized in the paper. The results show that the
method is comprehensive and fair to allocating the energy losses of a
power market to its participants.
Abstract: New regulations and standards for noise emission increasingly compel the automotive firms to make some improvements about decreasing the engine noise. Nowadays, the perforated reactive mufflers which have an effective damping capability are specifically used for this purpose. New designs should be analyzed with respect to both acoustics and back pressure. In this study, a reactive perforated muffler is investigated numerically and experimentally. For an acoustical analysis, the transmission loss which is independent of sound source of the present cross flow, the perforated muffler was analyzed by COMSOL. To be able to validate the numerical results, transmission loss was measured experimentally. Back pressure was obtained based on the flow field analysis and was also compared with experimental results. Numerical results have an approximate error of 20% compared to experimental results.
Abstract: Economic Load Dispatch (ELD) is a method of determining
the most efficient, low-cost and reliable operation of a power
system by dispatching available electricity generation resources to
supply load on the system. The primary objective of economic
dispatch is to minimize total cost of generation while honoring
operational constraints of available generation resources. In this paper
an intelligent water drop (IWD) algorithm has been proposed to
solve ELD problem with an objective of minimizing the total cost of
generation. Intelligent water drop algorithm is a swarm-based natureinspired
optimization algorithm, which has been inspired from natural
rivers. A natural river often finds good paths among lots of possible
paths in its ways from source to destination and finally find almost
optimal path to their destination. These ideas are embedded into
the proposed algorithm for solving economic load dispatch problem.
The main advantage of the proposed technique is easy is implement
and capable of finding feasible near global optimal solution with
less computational effort. In order to illustrate the effectiveness of
the proposed method, it has been tested on 6-unit and 20-unit test
systems with incremental fuel cost functions taking into account the
valve point-point loading effects. Numerical results shows that the
proposed method has good convergence property and better in quality
of solution than other algorithms reported in recent literature.
Abstract: In this paper, based on steady-state models of Flexible
AC Transmission System (FACTS) devices, the sizing of static
synchronous series compensator (SSSC) controllers in transmission
network is formed as an optimization problem. The objective of this
problem is to reduce the transmission losses in the network. The
optimization problem is solved using particle swarm optimization
(PSO) technique. The Newton-Raphson load flow algorithm is
modified to consider the insertion of the SSSC devices in the
network. A numerical example, illustrating the effectiveness of the
proposed algorithm, is introduced. In addition, a novel model of a 3-
phase voltage source converter (VSC) that is suitable for series
connected FACTS a controller is introduced. The model is verified
by simulation using Power System Blockset (PSB) and Simulink
software.
Abstract: This paper presents an efficient emission constrained
hydrothermal scheduling algorithm that deals with nonlinear
functions such as the water discharge characteristics, thermal cost,
and transmission loss. It is then incorporated into the hydrothermal
coordination program. The program has been tested on a practical
utility system having 32 thermal and 12 hydro generating units. Test
results show that a slight increase in production cost causes a
substantial reduction in emission.
Abstract: This paper presents a practical scheme that can be used for allocating the transmission loss to generators and loads. In this scheme first the share of a generator or load on the current through a branch is determined using Z-bus modified matrix. Then the current components are decomposed and the branch loss allocation is obtained. A motivation of proposed scheme is to improve the results of Z-bus method and to reach more fair allocation. The proposed scheme has been implemented and tested on several networks. To achieve practical and applicable results, the proposed scheme is simulated and compared on the transmission network (400kv) of Khorasan region in Iran and the 14-bus standard IEEE network. The results show that the proposed scheme is comprehensive and fair to allocating the energy losses of a power market to its participants.
Abstract: In this paper variation of spot price and total profits of
the generating companies- through wholesale electricity trading are
discussed with and without Central Generating Stations (CGS) share
and seasonal variations are also considered. It demonstrates how
proper analysis of generators- efficiencies and capabilities, types of
generators owned, fuel costs, transmission losses and settling price
variation using the solutions of Optimal Power Flow (OPF), can
allow companies to maximize overall revenue. It illustrates how
solutions of OPF can be used to maximize companies- revenue under
different scenarios. And is also extended to computation of Available
Transfer Capability (ATC) is very important to the transmission
system security and market forecasting. From these results it is
observed that how crucial it is for companies to plan their daily
operations and is certainly useful in an online environment of
deregulated power system. In this paper above tasks are demonstrated
on 124 bus real-life Indian utility power system of Andhra Pradesh
State Grid and results have been presented and analyzed.
Abstract: The accomplished study is based on the appointment
and identification of ageing effects and according to this absorption
of moisture of aircraft cabin components over the life-cycle. In the
first step of the study ceiling panels from same age and from the
same aircraft cabin have been examined according to weight changes
depending on the position in the aircraft cabin. In the second step of
the study different aged ceiling panels have been examined
concerning deflection, weight changes and the acoustic sound
transmission loss. To prove the assumption of water absorption
within the study and with the theoretical background from literature
and scientific papers, an older test panel was exposed extreme
thermal conditions (humidity and temperature) within a climate
chamber to show that there is a general ingress of water to cabin
components and that this ingress of water leads to the change of
different mechanical properties.
Abstract: The effects of global warming on India vary from the
submergence of low-lying islands and coastal lands to the melting of
glaciers in the Indian Himalayas, threatening the volumetric flow rate
of many of the most important rivers of India and South Asia. In
India, such effects are projected to impact millions of lives. As a
result of ongoing climate change, the climate of India has become
increasingly volatile over the past several decades; this trend is
expected to continue.
Climate change is one of the most important global environmental
challenges, with implications for food production, water supply,
health, energy, etc. Addressing climate change requires a good
scientific understanding as well as coordinated action at national and
global level. The climate change issue is part of the larger challenge
of sustainable development. As a result, climate policies can be more
effective when consistently embedded within broader strategies
designed to make national and regional development paths more
sustainable. The impact of climate variability and change, climate
policy responses, and associated socio-economic development will
affect the ability of countries to achieve sustainable development
goals.
A very well calibrated Soil and Water Assessment Tool (R2 =
0.9968, NSE = 0.91) was exercised over the Khatra sub basin of the
Kangsabati River watershed in Bankura district of West Bengal,
India, in order to evaluate projected parameters for agricultural
activities. Evapotranspiration, Transmission Losses, Potential
Evapotranspiration and Lateral Flow to reach are evaluated from the
years 2041-2050 in order to generate a picture for sustainable
development of the river basin and its inhabitants.
India has a significant stake in scientific advancement as well as
an international understanding to promote mitigation and adaptation.
This requires improved scientific understanding, capacity building,
networking and broad consultation processes. This paper is a
commitment towards the planning, management and development of
the water resources of the Kangsabati River by presenting detailed
future scenarios of the Kangsabati river basin, Khatra sub basin, over
the mentioned time period.
India-s economy and societal infrastructures are finely tuned to the
remarkable stability of the Indian monsoon, with the consequence
that vulnerability to small changes in monsoon rainfall is very high.
In 2002 the monsoon rains failed during July, causing profound loss
of agricultural production with a drop of over 3% in India-s GDP.
Neither the prolonged break in the monsoon nor the seasonal rainfall
deficit was predicted. While the general features of monsoon
variability and change are fairly well-documented, the causal
mechanisms and the role of regional ecosystems in modulating the
changes are still not clear. Current climate models are very poor at
modelling the Asian monsoon: this is a challenging and critical
region where the ocean, atmosphere, land surface and mountains all
interact. The impact of climate change on regional ecosystems is
likewise unknown. The potential for the monsoon to become more
volatile has major implications for India itself and for economies
worldwide. Knowledge of future variability of the monsoon system,
particularly in the context of global climate change, is of great
concern for regional water and food security.
The major findings of this paper were that of all the chosen
projected parameters, transmission losses, soil water content,
potential evapotranspiration, evapotranspiration and lateral flow to
reach, display an increasing trend over the time period of years 2041-
2050.