Abstract: Composite steel shear wall is a lateral load resisting system which consists of a steel plate with concrete wall attached to one or both sides to prevent it from elastic buckling. The composite behavior is ensured by utilizing high-strength bolts. This paper investigates the effect of distance between bolts, and for this purpose 14 one-story one-bay specimens with various bolts spacing were modeled by finite element code which is developed by the authors. To verify the model, numerical results were compared with a valid experiment which illustrate proper agreement. Results depict increasing the distance between bolts would improve the seismic ever, this increase must be limited, because of large distances will cause widespread buckling of the steel plate in free subpanels between bolts and would result in no improvement. By comparing the results in elastic region, it was observed initial stiffness is not affected by changing the distance.
Abstract: In this paper, the thermo-electro-structural coupledfield
in a cracked metal plate is studied using the finite element
analysis. From the computational results, the compressive stresses
reveal near the crack tip. This conclusion agrees with the past
reference. Furthermore, the compressive condition can retard and stop
the crack growth during the Joule heating process.
Abstract: The temperature distribution and the heat transfer
rates through a multi-layer door of a furnace were investigated. The
inside of the door was in contact with hot air and the other side of the
door was in contact with room air. Radiation heat transfer from the
walls of the furnace to the door and the door to the surrounding area
was included in the problem. This work is a two dimensional steady
state problem. The Churchill and Chu correlation was used to find
local convection heat transfer coefficients at the surfaces of the
furnace door. The thermophysical properties of air were the functions
of the temperatures. Polynomial curve fitting for the fluid properties
were carried out. Finite difference method was used to discretize for
conduction heat transfer within the furnace door. The Gauss-Seidel
Iteration was employed to compute the temperature distribution in
the door.
The temperature distribution in the horizontal mid plane of the
furnace door in a two dimensional problem agrees with the one
dimensional problem. The local convection heat transfer coefficients
at the inside and outside surfaces of the furnace door are exhibited.
Abstract: Highly pathogenic avian influenza (HPAI) H5N1 viruses have created demand for a cost-effective vaccine to prevent a pandemic of the disease. Here, we report that Trichoplusia ni (T. ni) larvae can act as a cost-effective bioreactor to produce recombinant HA5 (rH5HA) proteins as an potential effective vaccine for chickens. To facilitate the recombinant virus identification, virus titer determination and access the infected larvae, we employed the internal ribosome entry site (IRES) derived from Perina nuda virus (PnV, belongs to insect picorna like Iflavirus genus) to construct a bi-cistronic baculovirus expression vector that can express the rH5HA protein and enhanced green fluorescent protein (EGFP) simultaneously. Western blot analysis revealed that the 70 kDa rH5HA protein and partially cleaved products (40 kDa H5HA1) were generated in T. ni larvae infected with recombinant baculovirus carrying the H5HA gene. These data suggest that the baculovirus-larvae recombinant protein expression system could be a cost-effective platform for H5N1 vaccine production.
Abstract: Due to short product life cycles, increasing variety of
products and short cycles of leap innovations manufacturing
companies have to increase the flexibility of factory structures.
Flexibility of factory structures is based on defined factory planning
processes in which product, process and resource data of various
partial domains have to be considered. Thus factory planning
processes can be characterized as iterative, interdisciplinary and
participative processes [1]. To support interdisciplinary and
participative character of planning processes, a federative factory
data management (FFDM) as a holistic solution will be described.
FFDM is already implemented in form of a prototype. The interim
results of the development of FFDM will be shown in this paper. The
principles are the extracting of product, process and resource data
from documents of various partial domains providing as web services
on a server. The described data can be requested by the factory
planner by using a FFDM-browser.
Abstract: Pepper spray use has gained momentum since 1992
and although the active ingredient is readily available, it is considered
a weapon with restricted use in many regions, including The
Bahamas. In light of controversy in the literature regarding the
severity of presenting respiration complaints among individuals postacute
exposure of pepper spray inhalation, this descriptive case series
study was conducted to assess the respiratory status of persons
evaluated during a mass casualty in The Bahamas. Parameters noted
were patients- demographics and respiration severity determined via
clinical examination findings, disposition and follow-up review of the
20 persons. Their most common complaint was difficulty breathing
post exposure. Two required admission and stayed for
Abstract: A wireless power transfer system can attribute to the
fields in robot, aviation and space in which lightening the weight of
device and improving the movement play an important role. A
wireless power transfer system was investigated to overcome the
inconvenience of using power cable. Especially a wireless power
transfer technology is important element for mobile robots. We
proposed the wireless power transfer system of the half-bridge
resonant converter with the frequency tracking and optimized
power transfer control unit. And the possibility of the application
and development system was verified through the experiment with
LED loads.
Abstract: This research analyzes factors affecting the success of
Litecoin Value within Thailand and develops a guideline for selfreliance
for effective business implementation. Samples in this study
included 119 people through surveys. The results revealed four main
factors affecting the success as follows: 1) Future Career training
should be pursued in applied Litecoin development. 2) Didn't grasp
the concept of a digital currency or see the benefit of a digital
currency. 3) There is a great need to educate the next generation of
learners on the benefits of Litecoin within the community. 4) A great
majority didn't know what Litecoin was.
The guideline for self-reliance planning consisted of 4 aspects: 1)
Development planning: by arranging meet up groups to conduct
further education on Litecoin and share solutions on adoption into
every day usage. Local communities need to develop awareness of
the usefulness of Litecoin and share the value of Litecoin among
friends and family. 2) Computer Science and Business Management
staff should develop skills to expand on the benefits of Litecoin
within their departments. 3) Further research should be pursued on
how Litecoin Value can improve business and tourism within
Thailand. 4) Local communities should focus on developing Litecoin
awareness by encouraging street vendors to accept Litecoin as
another form of payment for services rendered.
Abstract: This paper describes dynamic analysis using proposed
fast finite element method for a shock absorbing structure including a
sponge. The structure is supported by nonlinear concentrated springs.
The restoring force of the spring has cubic nonlinearity and linear
hysteresis damping. To calculate damping properties for the structures
including elastic body and porous body, displacement vectors as
common unknown variable are solved under coupled condition. Under
small amplitude, we apply asymptotic method to complex eigenvalue
problem of this system to obtain modal parameters. And then
expressions of modal loss factor are derived approximately. This
approach was proposed by one of the authors previously. We call this
method as Modal Strain and Kinetic Energy Method (MSKE method).
Further, using the modal loss factors, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled equations using normal coordinate corresponding to linear
natural modes. This transformation yields computation efficiency. As
a numerical example of a shock absorbing structures, we adopt double
skins with a sponge. The double skins are supported by nonlinear
concentrated springs. We clarify influences of amplitude of the input
force on nonlinear and chaotic responses.
Abstract: Hand gesture is an active area of research in the vision
community, mainly for the purpose of sign language recognition and
Human Computer Interaction. In this paper, we propose a system to
recognize alphabet characters (A-Z) and numbers (0-9) in real-time
from stereo color image sequences using Hidden Markov Models
(HMMs). Our system is based on three main stages; automatic segmentation
and preprocessing of the hand regions, feature extraction
and classification. In automatic segmentation and preprocessing stage,
color and 3D depth map are used to detect hands where the hand
trajectory will take place in further step using Mean-shift algorithm
and Kalman filter. In the feature extraction stage, 3D combined features
of location, orientation and velocity with respected to Cartesian
systems are used. And then, k-means clustering is employed for
HMMs codeword. The final stage so-called classification, Baum-
Welch algorithm is used to do a full train for HMMs parameters.
The gesture of alphabets and numbers is recognized using Left-Right
Banded model in conjunction with Viterbi algorithm. Experimental
results demonstrate that, our system can successfully recognize hand
gestures with 98.33% recognition rate.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece using copper tools are being optimized
according to its individual machining characteristic i.e. Electrode
Wear Ratio (EWR). Higher EWR would give bad dimensional
precision for the EDM machined workpiece because of high
electrode wear. Hence, the quality characteristic for EWR is set to
lower-the-better to achieve the optimum dimensional precision for
the machined workpiece. Taguchi method has been used for the
construction, layout and analysis of the experiment for EWR
machining characteristic. The use of Taguchi method in the
experiment saves a lot of time and cost of preparing and machining
the experiment samples. Therefore, an L18 Orthogonal array
which was the fundamental component in the statistical design of
experiments has been used to plan the experiments and Analysis of
Variance (ANOVA) is used to determine the optimum machining
parameters for this machining characteristic. The control
parameters selected for this optimization experiments are polarity,
pulse on duration, discharge current, discharge voltage, machining
depth, machining diameter and dielectric liquid pressure. The
result had shown that negative polarity machining parameter
setting will decreases EWR.
Abstract: In recent times there has been a growing interest in the
development of quasi-two-dimensional niobium pentoxide (Nb2O5)
as a semiconductor for the potential electronic applications such as
capacitors, filtration, dye-sensitised solar cells and gas sensing
platforms. Therefore once the purpose is established, Nb2O5 can be
prepared in a number of nano- and sub-micron-structural
morphologies that include rods, wires, belts and tubes. In this study
films of Nb2O5 were prepared on gold plated silicon substrate using
spin-coating technique and subsequently by mechanical exfoliation.
The reason this method was employed was to achieve layers of less
than 15nm in thickness. The sintering temperature of the specimen
was 800oC. The morphology and structural characteristics of the
films were analyzed by Atomic Force Microscopy (AFM), Raman
Spectroscopy, X-ray Photoelectron Spectroscopy (XPS).
Abstract: Hydraulic conductivity is one parameter important for predicting the movement of water and contaminants dissolved in the water through the soil. The hydraulic conductivity is measured on soil samples in the lab and sometimes tests carried out in the field. The hydraulic conductivity has been related to soil particle diameter by a number of investigators. In this study, 25 set of soil samples with sand texture. The results show approximately success in predicting hydraulic conductivity from particle diameters data. The following relationship obtained from multiple linear regressions on data (R2 = 0.52): Where d10, d50 and d60, are the soil particle diameter (mm) that 10%, 50% and 60% of all soil particles are finer (smaller) by weight and Ks, saturated hydraulic conductivity is expressed in m/day. The results of regression analysis showed that d10 play a more significant role with respect to Ks, saturated hydraulic conductivity (m/day), and has been named as the effective parameter in Ks calculation.
Abstract: This study examines regional convergence in per capita personal income in the US and Canada. We find that the disparity in real per capita income levels across US states (Canadian provinces) has declined, but income levels are not identical. Income levels become more aligned once costs of living are accounted for in relative per capita income series. US states (Canadian provinces) converge at an annual rate of between 1.3% and 2.04% (between 2.15% and 2.37%). A pattern of σ and β-convergence in per capita personal income across regions evident over the entire sample period, is reversed over 1979-1989 (1976-1990) period. The reversal may be due to sectoral or region-specific shocks that have highly persistent effects. The latter explanation might be true for half of the US and most of Canada.
Abstract: Oleic acid (C18:1) play an important role in
proliferation of fat cells. In this study, the effect of oleate on cells
viability in 3T3-L1 cells (fat cells) was investigated. The 3T3-L1
cells were treated with various concentrations of oleate in the
presence of 23 mM glucose. Oleate was added to adipogenic media
(day 0) to investigate the influence of oleate on proliferation of
postconfluent preadipocytes after 24 h induction. 0.1 mM oleate
promoted cell division by increasing 33.9% number of cells from
basal control in postconfluent preadipocytes. However, there were no
significantly different in cells viability with control cells when oleate
concentrations were increased up to 0.5 mM. When added to
differentiated adipocytes (day 12) for 48 h, the number of cells
decreased as oleate concentrations increased. 92.7% of cells lost
demonstrated apoptosis and necrosis after 48 h with 0.5 mM oleate.
The fluorochrome staining was examined under fluorescence
microscopy using acridine orange and ethidium bromide double
staining. Furthermore, the presence of high lactate (60.6% increased
from basal control) released into plasma has shown the direct
cytotoxicity of 0.5 mM oleate on adipocytes.
Abstract: This experimental study examined the relationship
between pretend play and false-belief. Eighteen-month-old children
engaged in pretend play with an experimenter using various controlled
behaviors and performed a false-belief task. The results showed that
the children who understood pretend play performed better on the
false-belief task. This suggests that pretended play and false-belief are
related at the age of 18 months.
Abstract: The exact solutions of the equations describing the steady plane motion of an incompressible fluid of variable viscosity for an arbitrary state equation are determined in the (ξ,ψ) − or (η,ψ )- coordinates where ψ(x,y) is the stream function, ξ and η are the parts of the analytic function, ϖ =ξ( x,y )+iη( x,y ). Most of the solutions involve arbitrary function/ functions indicating
that the flow equations possess an infinite set of solutions.
Abstract: This paper propose the robust character segmentation method for license plate with topological transform such as twist,rotation. The first step of the proposed method is to find a candidate region for character and license plate. The character or license plate
must be appeared as closed loop in the edge image. In the case of
detecting candidate for character region, the evaluation of detected
region is using topological relationship between each character. When
this method decides license plate candidate region, character features
in the region with binarization are used. After binarization for the detected candidate region, each character region is decided again. In
this step, each character region is fitted more than previous step. In the
next step, the method checks other character regions with different
scale near the detected character regions, because most license plates
have license numbers with some meaningful characters around them.
The method uses perspective projection for geometrical normalization.
If there is topological distortion in the character region, the method
projects the region on a template which is defined as standard license
plate using perspective projection. In this step, the method is able to
separate each number region and small meaningful characters. The
evaluation results are tested with a number of test images.
Abstract: Successful intelligence (SI) is the integrated set of the
ability needed to attain success in life, within individual-s sociocultural
context. People are successfully intelligent by recognizing
their strengths and weaknesses. They will find ways to strengthen
their weakness and maintain their strength or even improve it. SI
people can shape, select, and adapt to the environments by using
balance of higher-ordered thinking abilities including; critical,
creative, and applicative. Aims: The purposes of this study were to;
1) develop curriculum that promotes SI for nursing students, and 2)
study the effectiveness of the curriculum development. Method:
Research and Development was a method used for this study. The
design was divided into two phases; 1) the curriculum development
which composed of three steps (needs assessment, curriculum
development and curriculum field trail), and 2) the curriculum
implementation. In this phase, a pre-experimental research design
(one group pretest-posttest design) was conducted. The sample
composed of 49 sophomore nursing students of Boromarajonani
College of Nursing, Surin, Thailand who enrolled in Nursing care of
Health problem course I in 2011 academic year. Data were carefully
collected using 4 instruments; 1) Modified essay questions test
(MEQ) 2) Nursing Care Plan evaluation form 3) Group processing
observation form (α = 0.74) and 4) Satisfied evaluation form of
learning (α = 0.82). Data were analyzed using descriptive statistics
and content analysis. Results: The results revealed that the sample
had post-test average score of SI higher than pre-test average score
(mean difference was 5.03, S.D. = 2.84). Fifty seven percentages of
the sample passed the MEQ posttest at the criteria of 60 percentages.
Students demonstrated the strategies of how to develop nursing care
plan. Overall, students- satisfaction on teaching performance was at
high level (mean = 4.35, S.D. = 0.46). Conclusion: This curriculum
can promote the attribute of characteristic of SI person and was
highly required to be continued.
Abstract: In this paper the authors propose a flexible electronic solution, to improve the energetic efficiency of a thermo plant. This is achieved by replacing the mechanical gear box, placed traditionally between a gas turbine and a synchronous generator; by a power electronic converter. After reminding problematic of gear boxes and interest of a proposed electronic solution in high power plants, the authors describe a new control strategy for an indirect frequency converter, which is characterized by its high efficiency due to the use of SWM: Square Wave Modulation. The main advantage of this mode is the quasi absence of switching losses. A control method is also proposed to resolve some problems incurred by using square wave modulation, in particular to reduce the harmonics distortion of the output inverter voltage and current. Simulation examples as well as experimental results are included.