Abstract: Dry reforming of methane that converts two greenhouses gases (CH4 and CO2) to synthesis gas (a mixture of H2 and CO) was studied in a commercial bench scale microwave (MW) plasma reactor system at atmospheric pressure. The CO2, CH4 and N2 conversions; H2, CO selectivities and yields, and syngas ratio (H2/CO) were investigated in a wide range of total feed flow rate (0.45 – 2.1 L/min), MW power (700 – 1200 watt) and CO2/CH4 molar ratio (2 – 5). At the feed flow rates of CH4, CO2 and N2 of 0.2, 0.4 and 1.5 L/min respectively, and the MWs input power of 700 W, the highest conversions of CH4 and CO2, selectivity and yield of H2, CO and H2/CO ratio of 79.35%, 44.82%, 50.12, 58.42, 39.77%, 32.89%, and 0.86, respectively, were achieved. The results of this work show that the product ratio increases slightly with the increasing total feed flow rate, but it decreases significantly with the increasing MW power and feeds CO2/CH4 ratio.
Abstract: This paper presents Buck-Boost converter topology to maintain the input power factor by using the power factor stage control and regulation stage control. Suppose, if we are using the RL load the power factor will be reduced due to the presence of total harmonic distortion in the current wave. To improve the power factor the current waveform should follow the fundamental component of the voltage waveform. These can be achieved by using the high -frequency power converter. Based on the resonant circuit the converter is able to perform the function of Buck, Boost, and buck-boost converter. Here ,we have used Buck-Boost converter, because, the buck-boost converter has more advantages than the boost converter. Here the switching action of the power converter can take place by using the external zero comparator PFC stage control. The power converter consisting of the resonant circuit which is used to control the output voltage gain of the converter. The power converter is operated at a very high switching frequency in the range of 400KHz in order to overcome the switching losses of the power converter. Due to presence of high switching frequency, the power factor will improve. Therefore, the total harmonics distortion present in the current waveform has also reduced. These results has generated in the form of simulation by using MATLAB/SIMULINK software. Similar to the Buck and Boost converters, the operation of the Buck-Boost has best understood, in terms of the inductor's "reluctance" for allowing rapid change in current, which also reduces the Total Harmonic Distortion (THD) in the input current waveform, which can improve the input Power factor, based on the type of load used.
Abstract: This paper presents an enhanced efficiency simultaneous dual band energy harvesting system for wireless body area network. A bulk biasing is used to enhance the efficiency of the adapted rectifier design to reduce Vth of MOSFET. The presented circuit harvests the radio frequency (RF) energy from two frequency bands: 1 GHz and 2.4 GHz. It is designed with TSMC 65-nm CMOS technology and high quality factor dual matching network to boost the input voltage. Full circuit analysis and modeling is demonstrated. The simulation results demonstrate a harvester with an efficiency of 23% at 1 GHz and 46% at 2.4 GHz at an input power as low as -30 dBm.
Abstract: Proposed paper dealt with the modelling and analysis of induction motor based on the mathematical expression using the graphical programming environment of Laboratory Virtual Instrument Engineering Workbench (LabVIEW). Induction motor modelling with the mathematical expression enables the motor to be simulated with the various required parameters. Owing to the invention of variable speed drives study about the induction motor characteristics became complex. In this simulation motor internal parameter such as stator resistance and reactance, rotor resistance and reactance, phase voltage, frequency and losses will be given as input. By varying the speed of motor corresponding parameters can be obtained they are input power, output power, efficiency, torque induced, slip and current.
Abstract: This paper discusses the design and analysis of a
hybrid PV-Fuel cell energy system destined to power a DC load. The
system is composed of a photovoltaic array, a fuel cell, an
electrolyzer and a hydrogen tank. HOMER software is used in this
study to calculate the optimum capacities of the power system
components that their combination allows an efficient use of solar
resource to cover the hourly load needs. The optimal system sizing
allows establishing the right balance between the daily electrical
energy produced by the power system and the daily electrical energy
consumed by the DC load using a 28 KW PV array, a 7.5 KW fuel
cell, a 40KW electrolyzer and a 270 Kg hydrogen tank. The variation
of powers involved into the DC bus of the hybrid PV-fuel cell system
has been computed and analyzed for each hour over one year: the
output powers of the PV array and the fuel cell, the input power of
the elctrolyzer system and the DC primary load. Equally, the annual
variation of stored hydrogen produced by the electrolyzer has been
assessed. The PV array contributes in the power system with 82%
whereas the fuel cell produces 18%. 38% of the total energy
consumption belongs to the DC primary load while the rest goes to
the electrolyzer.
Abstract: In this paper a new design of a broadband microwave
power limiter is presented and validated into simulation by using
ADS software (Advanced Design System) from Agilent technologies.
The final circuit is built on microstrip lines by using identical Zero
Bias Schottky diodes. The power limiter is designed by Associating 3
stages Schottky diodes. The obtained simulation results permit to
validate this circuit with a threshold input power level of 0 dBm until
a maximum input power of 30 dBm.
Abstract: Instantaneous electromagnetic torque of simple reflectance generator can be positive at a time and negative at other time. It is utilized to design a permanent magnet reluctance generator specifically. Generator is designed by combining two simple reluctance generators, consists of two rotors mounted on the same shaft, two output-windings and a field source of the permanent magnet. By this design, the electromagnetic torque on both rotor will be eliminated each other, so the input torque generator can be smaller. Rotor is expected only to regulate the flux flow to both output windings alternately, until the magnetic energy is converted into electrical energy, such as occurs in the transformer energy conversion. The prototype trials have been made to test this design. The test result show that the new design of permanent magnets reluctance generator able to convert energy from permanent magnets into electrical energy, this is proven by the existence 167% power output compared to the shaft input power.
Abstract: This study examined the effect of porous dielectric silica gel the discharge ignition voltage and input power in a plasma reactor. For the experiment was used a plasma reactor with two mesh electrodes made of stainless steel with a mesh size of 0.1x0.1mm. The study analyzed and compared with parameters such as power, ignition and operation voltage of the reactor for two dielectrics a porous and glass. During experiment were observed several new phenomena conducted for porous dielectric. The first phenomenon was the reduction the ignition voltage discharge to volume around few hundred volts. Second it was increase input power six times more compared with power those obtained for the glass dielectric. Thirdly difference it is ΔV between ignition voltage Vi and operating voltage reactor Vm for porous dielectric it was 11%, while ΔV for the glass dielectric it was 60%. Also change the discharge characteristics from DBD for glass dielectric to the streamer resistance discharge for the porous dielectric.
Abstract: In this paper the application of a hierarchical fuzzy system (HFS) based on MPSS and SVC in multi-machine environment is studied. Also the effect of communication lines active power variance signal between two ΔPTie-line regions, as one of the inputs of hierarchical fuzzy multi-input PSS and SVC (HFMPSS & SVC), on the increase of low frequency oscillation damping is examined. In the MPSS, to have better efficiency an auxiliary signal of reactive power deviation (ΔQ) is added with ΔP+ Δω input type PSS. The number of rules grows exponentially with the number of variables in a classic fuzzy system. To reduce the number of rules the HFS consists of a number of low-dimensional fuzzy systems in a hierarchical structure. Phasor model of SVC is described and used in this paper. The performances of MPSS and ΔPTie-line based HFMPSS and also the proposed method in damping inter-area mode of oscillation are examined in response to disturbances. The efficiency of the proposed model is examined by simulating a four-machine power system. Results show that the proposed method is performing satisfactorily within the whole range of disturbances and reduces the cost of system.
Abstract: The selection of control strategy depends on the converters of the drive including power, speed, performance and the possible system costs. A number of attempts were therefore made in recent times to develop novel power electronic converter structures for SRM drives, based on the utilization. Many of the converters with variable speed drives have no input power factor correction circuits. This results in harmonic pollution of the utility supply, which should be avoided. The effect of power factor variation in terms of harmonic content is also analyzed in this study. The proposed topologies were simulated using MATLAB / Simulink software package and the results are obtained.
Abstract: A high thermal dissipation performance polyethylene terephthalate heat pipe has been fabricated and tested in this research. Polyethylene terephthalate (PET) is used as the container material instead of copper. Copper mesh and methanol are sealed in the middle of two PET films as the wick structure and working fluid. Although the thermal conductivity of PET (0.15-0.24 W/m·K) is much smaller than copper (401 W/m·K), the experiment results reveal that the PET heat pipe can reach a minimum thermal resistance of 0.146 (oC/W) and maximum effective thermal conductivity of 18,310 (W/m·K) with 36.9 vol% at 26 W input power. However, when the input power is larger than 30 W, the laminated PET will debond due to the high vapor pressure of methanol.
Abstract: In this work we present a solution for DAGC (Digital
Automatic Gain Control) in WLAN receivers compatible to IEEE 802.11a/g standard. Those standards define communication in 5/2.4
GHz band using Orthogonal Frequency Division Multiplexing OFDM modulation scheme. WLAN Transceiver that we have used
enables gain control over Low Noise Amplifier (LNA) and a
Variable Gain Amplifier (VGA). The control over those signals is
performed in our digital baseband processor using dedicated hardware block DAGC. DAGC in this process is used to automatically control the VGA and LNA in order to achieve better
signal-to-noise ratio, decrease FER (Frame Error Rate) and hold the
average power of the baseband signal close to the desired set point.
DAGC function in baseband processor is done in few steps: measuring power levels of baseband samples of an RF signal,accumulating the differences between the measured power level and
actual gain setting, adjusting a gain factor of the accumulation, and
applying the adjusted gain factor the baseband values. Based on the measurement results of RSSI signal dependence to input power we have concluded that this digital AGC can be implemented applying
the simple linearization of the RSSI. This solution is very simple but also effective and reduces complexity and power consumption of the
DAGC. This DAGC is implemented and tested both in FPGA and in ASIC as a part of our WLAN baseband processor. Finally, we have integrated this circuit in a compact WLAN PCMCIA board based on MAC and baseband ASIC chips designed from us.
Abstract: The absolute Cu atoms density in Cu(2S1/22P1/2)
ground state has been measured by Resonance Optical Absorption
(ROA) technique in a DC magnetron sputtering deposition with
argon. We measured these densities under variety of operation
conditions: pressure from 0.6 μbar to 14 μbar, input power from
10W to 200W and N2 mixture from 0% to 100%. For measuring the
gas temperature, we used the simulation of N2 rotational spectra
with a special computer code. The absolute number density of Cu
atoms decreases with increasing the N2 percentage of buffer gas at
any conditions of this work. But the deposition rate, is not decreased
with the same manner. The deposition rate variation is very small
and in the limit of quartz balance measuring equipment accuracy. So
we conclude that decrease in the absolute number density of Cu
atoms in magnetron plasma has not a big effect on deposition rate,
because the diffusion of Cu atoms to the chamber volume and
deviation of Cu atoms from direct path (towards the substrate)
decreases with increasing of N2 percentage of buffer gas. This is
because of the lower mass of N2 atoms compared to the argon ones.
Abstract: Nowadays in applications of renewable energy sources
it is important to develop powerful and energy-saving photovoltaic
converters and to keep the prescriptions of the standards. In grid
connected PV converters the obvious solution to increase the
efficiency is to reduce the switching losses. Our new developed
control method reduces the switching losses and keeps the limitations
of the harmonic distortion standards. The base idea of the method is
the utilization of 3-state control causing discontinuous current mode
at low input power. In the following sections the control theory, the
realizations and the simulation results are presented.
Abstract: this paper focuses on designing of PSS and SVC
controller based on chaos and PSO algorithms to improve the
stability of power system. Single machine infinite bus (SMIB) system
with SVC located at the terminal of generator has been considered to
evaluate the proposed controllers where both SVC and PSS have the
same controller. The coefficients of PSS and SVC controller have
been optimized by chaos and PSO algorithms. Finally the system
with proposed controllers has been simulated for the special
disturbance in input power of generator, and then the dynamic
responses of generator have been presented. The simulation results
showed that the system composed with recommended controller has
outstanding operation in fast damping of oscillations of power system.
Abstract: The substrate heater designed for this investigation is a front side substrate heating system. It consists of 10 conventional tungsten halogen lamps and an aluminum reflector, total input electrical power of 5 kW. The substrate is heated by means of a radiation from conventional tungsten halogen lamps directed to the substrate through a glass window. This design allows easy replacement of the lamps and maintenance of the system. Within 2 to 6 minutes the substrate temperature reaches 500 to 830 C by varying the vertical distance between the glass window and the substrate holder. Moreover, the substrate temperature can be easily controlled by controlling the input power to the system. This design gives excellent opportunity to deposit many deferent films at deferent temperatures in the same deposition time. This substrate heater was successfully used for Chemical Vapor Deposition (CVD) of many thin films, such as Silicon, iron, etc.
Abstract: This paper describes the gain and noise performances
of discrete Raman amplifier as a function of fiber lengths and the
signal input powers for different pump configurations. Simulation has
been done by using optisystem 7.0 software simulation at signal
wavelength of 1550 nm and a pump wavelength of 1450nm. The
results showed that the gain is higher in bidirectional pumping than in
counter pumping, the gain changes with increasing the fiber length
while the noise figure remain the same for short fiber lengths and the
gain saturates differently for different pumping configuration at
different fiber lengths and power levels of the signal.
Abstract: We study the performance of compressed beamforming
weights feedback technique in generalized triangular decomposition
(GTD) based MIMO system. GTD is a beamforming technique that
enjoys QoS flexibility. The technique, however, will perform at its
optimum only when the full knowledge of channel state information
(CSI) is available at the transmitter. This would be impossible in
the real system, where there are channel estimation error and limited
feedback. We suggest a way to implement the quantized beamforming
weights feedback, which can significantly reduce the feedback data,
on GTD-based MIMO system and investigate the performance of
the system. Interestingly, we found that compressed beamforming
weights feedback does not degrade the BER performance of the
system at low input power, while the channel estimation error
and quantization do. For comparison, GTD is more sensitive to
compression and quantization, while SVD is more sensitive to the
channel estimation error. We also explore the performance of GTDbased
MU-MIMO system, and find that the BER performance starts
to degrade largely at around -20 dB channel estimation error.
Abstract: This paper proposes the application of a hierarchical fuzzy system (HFS) based on multi-input power system stabilizer (MPSS) and also Static Var Compensator (SVC) in multi-machine environment.The number of rules grows exponentially with the number of variables in a conventional fuzzy logic system. The proposed HFS method is developed to solve this problem. To reduce the number of rules the HFS consists of a number of low-dimensional fuzzy systems in a hierarchical structure. In fact, by using HFS the total number of involved rules increases only linearly with the number of input variables. In the MPSS, to have better efficiency an auxiliary signal of reactive power deviation (ΔQ) is added with ΔP+ Δω input type Power system stabilizer (PSS). Phasor model of SVC is described and used in this paper. The performances of MPSS, Conventional power system stabilizer (CPSS), hierarchical Fuzzy Multi-input Power System Stabilizer (HFMPSS) and the proposed method in damping inter-area mode of oscillation are examined in response to disturbances. By using digital simulations the comparative study is illustrated. It can be seen that the proposed PSS is performing satisfactorily within the whole range of disturbances.
Abstract: A generalized method for small-signal simulation of
avalanche noise in Mixed Tunneling Avalanche Transit Time
(MITATT) device is presented in this paper where the effect of series
resistance is taken into account. The method is applied to a
millimeter-wave Double Drift Region (DDR) MITATT device based
on Silicon to obtain noise spectral density and noise measure as a
function of frequency for different values of series resistance. It is
found that noise measure of the device at the operating frequency
(122 GHz) with input power density of 1010 Watt/m2 is about 35 dB
for hypothetical parasitic series resistance of zero ohm (estimated
junction temperature = 500 K). Results show that the noise measure
increases as the value of parasitic resistance increases.