Abstract: In this study, supercritical steam is introduced to Combined Cycle Power Plant (CCPP) in an attempt to further optimize energy recovery. Subcritical steam is commonly used in the CCPP, operating at maximum pressures around 150-160 bar. Supercritical steam is an alternative to increase heat recovery during vaporization period of water. The idea of improvement using supercritical steam is further examined with the use of exergy, pinch analysis and Aspen Plus simulation.
Abstract: Landfilling of organic waste is still the predominant waste management method in the USA and Canada. Strategic plans for waste diversion from landfills are needed to increase material recovery and energy generation from waste. In this paper, we carried out a statistical survey on waste flow in the two cities New York and Montréal and estimated the energy recovery potential for each case. Data collection and analysis of the organic waste (food waste, yard waste, etc.), paper and cardboard, metal, glass, plastic, carton, textile, electronic products and other materials were done based on the reports published by the Department of Sanitation in New York and Service de l'Environnement in Montréal. In order to calculate the gas generation potential of organic waste, Buswell equation was used in which the molar mass of the elements was calculated based on their atomic weight and the amount of organic waste in New York and Montréal. Also, the higher and lower calorific value of the organic waste (solid base) and biogas (gas base) were calculated. According to the results, only 19% (598 kt) and 45% (415 kt) of New York and Montréal waste were diverted from landfills in 2017, respectively. The biogas generation potential of the generated food waste and yard waste amounted to 631 million m3 in New York and 173 million m3 in Montréal. The higher and lower calorific value of food waste were 3482 and 2792 GWh in New York and 441 and 354 GWh in Montréal, respectively. In case of yard waste, they were 816 and 681 GWh in New York and 636 and 531 GWh in Montréal, respectively. Considering the higher calorific value, this amount would mean a contribution of around 2.5% energy in these cities.
Abstract: This paper investigates the possibility of using three systems of organic Rankine auxiliary power generation, ejector refrigeration and absorption to recover energy from a diesel car. The analysis is done for both urban and suburban driving modes that vary from 60 to 120 km/h. Various refrigerants have also been used for organic Rankine and Ejector refrigeration cycles. The capacity was evaluated by Organic Rankine Cycle (ORC) system in both urban and suburban conditions for cyclopentane and ammonia as refrigerants. Also, for these two driving plans, produced cooling by absorption refrigeration system under variable ambient temperature conditions and in ejector refrigeration system for R123, R134a and R141b refrigerants were investigated.
Abstract: A thermodynamic study is performed on the Reverse Osmosis (RO) desalination process for brackish water. The detailed RO model of thermodynamics properties with and without an energy recovery device was built in Simulink/MATLAB and validated against reported measurement data. The efficiency of desalination plants can be estimated by both the first and second laws of thermodynamics. While the first law focuses on the quantity of energy, the second law analysis (i.e. exergy analysis) introduces quality. This paper used the Main Outfall Drain in Iraq as a case study to conduct energy and exergy analysis of RO process. The result shows that it is feasible to use energy recovery method for reverse osmosis with salinity less than 15000 ppm as the exergy efficiency increases twice. Moreover, this analysis shows that the highest exergy destruction occurs in the rejected water and lowest occurs in the permeate flow rate accounting 37% for 4.3% respectively.
Abstract: This paper describes the results obtained in a two-year randomized intervention field study investigating the impact of ventilation rates on indoor air quality (IAQ) and the respiratory health of asthmatic children in Québec City, Canada. The focus of this article is on the comparative effectiveness of heat recovery ventilators (HRVs) and energy recovery ventilators (ERVs) at increasing ventilation rates, improving IAQ, and maintaining an acceptable indoor relative humidity (RH). In 14% of the homes, the RH was found to be too low in winter. Providing more cold and dry outside air to under-ventilated homes in winter further reduces indoor RH. Thus, low-RH homes in the intervention group were chosen to receive ERVs (instead of HRVs) to increase the ventilation rate. The installation of HRVs or ERVs led to a near doubling of the ventilation rates in the intervention group homes which led to a significant reduction in the concentration of several key of pollutants. The ERVs were also effective in maintaining an acceptable indoor RH since they avoided excessive dehumidification of the home by recovering moisture from the exhaust airstream through the enthalpy core, otherwise associated with increased cold supply air rates.
Abstract: This study is aimed at exploring the possibility of energy recovery through the suppression of vibrations. The article describes design of electromagnetic dynamic damper. The magnetic part of the device performs the function of a tuned mass damper, thereby providing both energy regeneration and damping properties to the protected mass. According to the theory of tuned mass damper, equations of mathematical models were obtained. Then, under given properties of current system, amplitude frequency response was investigated. Therefore, main ideas and methods for further research were defined.
Abstract: This paper aims to determine the best environmental and economic scenario for Municipal Solid Waste (MSW) management of the Maku city by using Life Cycle Assessment (LCA) approach. The functional elements of this study are collection, transportation, and disposal of MSW in Maku city. Waste composition and density, as two key parameters of MSW, have been determined by field sampling, and then, the other important specifications of MSW like chemical formula, thermal energy and water content were calculated. These data beside other information related to collection and disposal facilities are used as a reliable source of data to assess the environmental impacts of different waste management options, including landfills, composting, recycling and energy recovery. The environmental impact of MSW management options has been investigated in 15 different scenarios by Integrated Waste Management (IWM) software. The photochemical smog, greenhouse gases, acid gases, toxic emissions, and energy consumption of each scenario are measured. Then, the environmental indices of each scenario are specified by weighting these parameters. Economic costs of scenarios have been also compared with each other based on literature. As final result, since the organic materials make more than 80% of the waste, compost can be a suitable method. Although the major part of the remaining 20% of waste can be recycled, due to the high cost of necessary equipment, the landfill option has been suggested. Therefore, the scenario with 80% composting and 20% landfilling is selected as superior environmental and economic scenario. This study shows that, to select a scenario with practical applications, simultaneously environmental and economic aspects of different scenarios must be considered.
Abstract: Renewable energy recovery is an important domain of research in past few years in view of protection of our ecosystem. Several industrial companies are setting up widespread recovery systems to exploit wave energy. Most of them have a large size, are implanted near the shores and exploit current flows. However, as oceans represent 70% of Earth surface, a huge space is still unexploited to produce energy. Present analysis focuses on surface small scale wave energy recovery. The principle is exactly the opposite of wheel damper for a car on a road. Instead of maintaining the car body as non-oscillatory as possible by adapted control, a system is designed so that its oscillation amplitude under wave action will be maximized with respect to a boat carrying it in view of differential potential energy recuperation. From parametric analysis of system equations, interesting domains have been selected and expected energy output has been evaluated.
Abstract: Quick development and usage of nanotechnology have resulted to massive use of various nanoparticles, such as iron oxide nanoparticles (IONPs) and multi-wall carbon nanotubes (MWCNTs). Thus, this study investigated the role of IONPs and MWCNTs in enhancing bioenergy recovery. Results show that IONPs at a concentration of 750 mg/L and MWCNTs at a concentration of 1500 mg/L induced faster substrate utilization and biogas production rates than the control. IONPs exhibited higher carbon oxygen demand (COD) removal efficiency than MWCNTs while on the contrary, MWCNT performance on biogas generation was remarkable than IONPs. Furthermore, scanning electron microscopy (SEM) investigation revealed extracellular polymeric substances (EPS) excretion from AGS had an interaction with nanoparticles. This interaction created a protective barrier to microbial consortia hence reducing their cytotoxicity. Microbial community analyses revealed genus predominance of bacteria of Anaerolineaceae and Longilinea. Their role in biodegradation of the substrate could have highly been boosted by nanoparticles. The archaea predominance of the genus level of Methanosaeta and Methanobacterium enhanced methanation process. The presence of bacteria of genus Geobacter was also reported. Their presence might have significantly contributed to direct interspecies electron transfer in the system. Exposure of AGS to nanoparticles promoted direct interspecies electron transfer among the anaerobic fermenting bacteria and their counterpart methanogens during the anaerobic digestion process. This results provide useful insightful information in understanding the response of microorganisms to IONPs and MWCNTs in the complex natural environment.
Abstract: Anaerobic digestion is a well-known technique for
sustainable energy recovery from sewage sludge. However, sewage
sludge digestion is restricted due to certain factors. Pre-treatment
methods have been established in various publications as a promising
technique to improve the digestibility of the sewage sludge and to
enhance the biogas generated which can be used for energy recovery.
In this study, continuous flow microwave (MW) pre-treatment with
different intensities were compared by using 5 L semi-continuous
digesters at a hydraulic retention time of 27 days. We focused on the
effects of MW at different intensities on the sludge solubilization,
sludge digestibility, and biogas production of the untreated and MW
pre-treated sludge. The MW pre-treatment demonstrated an increase
in the ratio of soluble chemical oxygen demand to total chemical
oxygen demand (sCOD/tCOD) and volatile fatty acid (VFA)
concentration. Besides that, the total volatile solid (TVS) removal
efficiency and tCOD removal efficiency also increased during the
digestion of the MW pre-treated sewage sludge compared to the
untreated sewage sludge. Furthermore, the biogas yield also
subsequently increases due to the pre-treatment effect. A higher MW
power level and irradiation time generally enhanced the biogas
generation which has potential for sustainable energy recovery from
sewage treatment plant. However, the net energy balance tabulation
shows that the MW pre-treatment leads to negative net energy production.
Abstract: Biomass treatment through densification is very suitable and helpful technology before its effective energy recovery. Densification process of biomass is significantly influenced by various technological and material variables, which are ultimately reflected on the final solid biofuels quality. The paper deals with the experimental research of the relationship between technological and material variables during densification of fast-growing trees, roundly fast-growing willows. The main goal of presented experimental research is to determine the relationship between compression pressure and raw material particle size from a final briquettes density point of view. Experimental research was realized by single-axis densification. The impact of particle size with interaction of compression pressure and stabilization time on the quality properties of briquettes was determined. These variables interaction affects the final solid biofuels (briquettes) quality. From briquettes production point of view and from densification machines constructions point of view is very important to know about mutual interaction of these variables on final briquettes quality. The experimental findings presented here are showing the importance of mentioned variables during the densification process.
Abstract: The efficiency of the actuation system of exoskeletons
and active orthoses for lower limbs is a significant aspect of the
design of such devices because it affects their efficacy. The F-IVT is
an innovative actuation system to power artificial knee joint with
energy recovery capabilities. Its key and non-conventional elements
are a flywheel that acts as a mechanical energy storage system, and
an Infinitely Variable Transmission (IVT). The design of the F-IVT
can be optimized for a certain walking condition, resulting in a heavy
reduction of both the electric energy consumption and of the electric
peak power. In this work, by means of simulations of level ground
walking at different speeds, it is demonstrated that the F-IVT is still
an advantageous actuator which permits to save energy consumption
and to downsize the electric motor even when it does not work in
nominal conditions.
Abstract: New advancement of technology and never satisfying demands of the civilization are putting huge pressure on the natural fuel resources and these resources are at a constant threat to its sustainability. To get the best out of the automobile, the optimum balance between performance and fuel economy is important. In the present state of art, either of the above two aspects are taken into mind while designing and development process which puts the other in the loss as increase in fuel economy leads to decrement in performance and vice-versa. In-depth observation of the vehicle dynamics apparently shows that large amount of energy is lost during braking and likewise large amount of fuel is consumed to reclaim the initial state, this leads to lower fuel efficiency to gain the same performance. Current use of Kinetic Energy Recovery System is only limited to sports vehicles only because of the higher cost of this system. They are also temporary in nature as power can be squeezed only during a small time duration and use of superior parts leads to high cost, which results on concentration on performance only and neglecting the fuel economy. In this paper Kinetic Energy Recovery System for storing the power and then using the same while accelerating has been discussed. The major storing element in this system is a Flat Spiral Spring that will store energy by compression and torsion.
The use of spring ensure the permanent storage of energy until used by the driver unlike present mechanical regeneration system in which the energy stored decreases with time and is eventually lost. A combination of internal gears and spur gears will be used in order to make the energy release uniform which will lead to safe usage. The system can be used to improve the fuel efficiency by assisting in overcoming the vehicle’s inertia after braking or to provide instant acceleration whenever required by the driver. The performance characteristics of the system including response time, mechanical efficiency and overall increase in efficiency are demonstrated. This technology makes the KERS (Kinetic Energy Recovery System) more flexible and economical allowing specific application while at the same time increasing the time frame and ease of usage.
Abstract: Full adders are important components in applications
such as digital signal processors (DSP) architectures and
microprocessors. In addition to its main task, which is adding two
numbers, it participates in many other useful operations such as
subtraction, multiplication, division,, address calculation,..etc. In
most of these systems the adder lies in the critical path that
determines the overall speed of the system. So enhancing the
performance of the 1-bit full adder cell (the building block of the
adder) is a significant goal.Demands for the low power VLSI have
been pushing the development of aggressive design methodologies to
reduce the power consumption drastically. To meet the growing
demand, we propose a new low power adder cell by sacrificing the
MOS Transistor count that reduces the serious threshold loss
problem, considerably increases the speed and decreases the power
when compared to the static energy recovery full (SERF) adder. So a
new improved 14T CMOS l-bit full adder cell is presented in this
paper. Results show 50% improvement in threshold loss problem,
45% improvement in speed and considerable power consumption
over the SERF adder and other different types of adders with
comparable performance.
Abstract: Solid waste can be considered as an urban burden or
as a valuable resource depending on how it is managed. To meet the
rising demand for energy and to address environmental concerns, a
conversion from conventional energy systems to renewable resources
is essential. For the sustainability of human civilization, an
environmentally sound and techno-economically feasible waste
treatment method is very important to treat recyclable waste. Several
technologies are available for realizing the potential of solid waste as
an energy source, ranging from very simple systems for disposing of
dry waste to more complex technologies capable of dealing with
large amounts of industrial waste. There are three main pathways for
conversion of waste material to energy: thermo chemical,
biochemical and physicochemical. This paper investigates the thermo
chemical conversion of solid waste for energy recovery. The
processes, advantages and dis-advantages of various thermo chemical
conversion processes are discussed and compared. Special attention
is given to Gasification process as it provides better solutions
regarding public acceptance, feedstock flexibility, near-zero
emissions, efficiency and security. Finally this paper presents
comparative statements of thermo chemical processes and introduces
an integrated waste management system.
Abstract: Waste management is now a global concern due to its
high environmental impact on climate change. Because of generating
huge amount of waste through our daily activities, managing waste in
an efficient way has become more important than ever. Alternative
Waste Technology (AWT), a new category of waste treatment
technology has been developed for energy recovery in recent years to
address this issue. AWT describes a technology that redirects waste
away from landfill, recovers more useable resources from the waste
flow and reduces the impact on the surroundings. Australia is one of
the largest producers of waste per-capita. A number of AWTs are
using in Australia to produce energy from waste. Presently, it is vital
to identify an appropriate AWT to establish a sustainable waste
management system in Australia. Identification of an appropriate
AWT through Multi-criteria analysis (MCA) of four AWTs by using
five key decision making criteria is presented and discussed in this
paper.
Abstract: As the data-driven economy is growing faster than
ever and the demand for energy is being spurred, we are facing
unprecedented challenges of improving energy efficiency in data
centers. Effectively maximizing energy efficiency or minimising the
cooling energy demand is becoming pervasive for data centers. This
paper investigates overall energy consumption and the energy
efficiency of cooling system for a data center in Finland as a case
study. The power, cooling and energy consumption characteristics
and operation condition of facilities are examined and analysed.
Potential energy and cooling saving opportunities are identified and
further suggestions for improving the performance of cooling system
are put forward. Results are presented as a comprehensive evaluation
of both the energy performance and good practices of energy
efficient cooling operations for the data center. Utilization of an
energy recovery concept for cooling system is proposed. The
conclusion we can draw is that even though the analysed data center
demonstrated relatively high energy efficiency, based on its power
usage effectiveness value, there is still a significant potential for
energy saving from its cooling systems.
Abstract: An improved topology of a voltage-fed quasi-resonant
soft switching LCrCdc series-parallel half bridge inverter with a constant-frequency for electronic ballast applications is proposed in this paper. This new topology introduces a low-cost solution to
reduce switching losses and circuit rating to achieve high-efficiency
ballast. Switching losses effect on ballast efficiency is discussed
through experimental point of view. In this discussion, an improved
topology in which accomplishes soft switching operation over a wide
power regulation range is proposed. The proposed structure uses reverse recovery diode to provide better operation for the ballast system. A symmetrical pulse wide modulation (PWM) control scheme is implemented to regulate a wide range of out-put power.
Simulation results are kindly verified with the experimental
measurements obtained by ballast-lamp laboratory prototype. Different load conditions are provided in order to clarify the
performance of the proposed converter.