Abstract: In this paper, a fuzzy controller is designed for
stabilization of the Lorenz chaotic equations. A simple Mamdani
inference method is used for this purpose. This method is very simple
and applicable for complex chaotic systems and it can be
implemented easily. The stability of close loop system is investigated
by the Lyapunov stabilization criterion. A Lyapunov function is
introduced and the global stability is proven. Finally, the
effectiveness of this method is illustrated by simulation results and it
is shown that the performance of the system is improved.
Abstract: The paper deals with the comparison study of
harmonic detection methods for a shunt active power filter. The
%THD and the power factor value at the PCC point after
compensation are considered for the comparison. There are three
harmonic detection methods used in the paper that are synchronous
reference frame method, synchronous detection method, and DQ axis
with Fourier method. In addition, the ideal current source is used to
represent the active power filter by assuming an infinitely fast
controller action of the active power filter. The simulation results
show that the DQ axis with Fourier method provides the minimum
%THD after compensation compared with other methods. However,
the power factor value at the PCC point after compensation is slightly
lower than that of synchronous detection method.
Abstract: In this study, a robust intelligent backstepping tracking control (RIBTC) system combined with adaptive output recurrent cerebellar model articulation control (AORCMAC) and H∞ control technique is proposed for wheeled inverted pendulums (WIPs) real-time control with exact system dynamics unknown. Moreover, a robust H∞ controller is designed to attenuate the effect of the residual approximation errors and external disturbances with desired attenuation level. The experimental results indicate that the WIPs can stand upright stably when using the proposed RIBTC.
Abstract: A nonlinear optimal controller with a fuzzy gain
scheduler has been designed and applied to a Line-Of-Sight (LOS)
stabilization system. Use of Linear Quadratic Regulator (LQR)
theory is an optimal and simple manner of solving many control
engineering problems. However, this method cannot be utilized
directly for multigimbal LOS systems since they are nonlinear in
nature. To adapt LQ controllers to nonlinear systems at least a
linearization of the model plant is required. When the linearized
model is only valid within the vicinity of an operating point a gain
scheduler is required. Therefore, a Takagi-Sugeno Fuzzy Inference
System gain scheduler has been implemented, which keeps the
asymptotic stability performance provided by the optimal feedback
gain approach. The simulation results illustrate that the proposed
controller is capable of overcoming disturbances and maintaining a
satisfactory tracking performance.
Abstract: This research investigates the design of a low-cost 3D
spatial interaction approach using the Wii Remote for immersive
Head-Mounted Display (HMD) virtual reality. Current virtual reality
applications that incorporate the Wii Remote are either desktop
virtual reality applications or systems that use large screen displays.
However, the requirements for an HMD virtual reality system differ
from such systems. This is mainly because in HMD virtual reality,
the display screen does not remain at a fixed location. The user views
the virtual environment through display screens that are in front of
the user-s eyes and when the user moves his/her head, these screens
move as well. This means that the display has to be updated in realtime
based on where the user is currently looking. Normal usage of
the Wii Remote requires the controller to be pointed in a certain
direction, typically towards the display. This is too restrictive for
HMD virtual reality systems that ideally require the user to be able to
turn around in the virtual environment. Previous work proposed a
design to achieve this, however it suffered from a number of
drawbacks. The aim of this study is to look into a suitable method of
using the Wii Remote for 3D interaction in a space around the user
for HMD virtual reality. This paper presents an overview of issues
that had to be considered, the system design as well as experimental
results.
Abstract: In the control theory one attempts to find a controller
that provides the best possible performance with respect to some
given measures of performance. There are many sorts of controllers
e.g. a typical PID controller, LQR controller, Fuzzy controller etc. In
the paper will be introduced polynomial controller with novel tuning
method which is based on the special pole placement encoding
scheme and optimization by Genetic Algorithms (GA). The examples
will show the performance of the novel designed polynomial
controller with comparison to common PID controller.
Abstract: This paper presents the optimal controller design of
the generator control unit in the aircraft power system. The adaptive
tabu search technique is applied to tune the controller parameters
until the best terminal output voltage of generator is achieved. The
output response from the system with the controllers designed by the
proposed technique is compared with those from the conventional
method. The transient simulations using the commercial software
package show that the controllers designed from the adaptive tabu
search algorithm can provide the better output performance compared
with the result from the classical method. The proposed design
technique is very flexible and useful for electrical aircraft engineers.
Abstract: In this article, LQR based PID controller design for
3DOF helicopter system is investigated. The 3-DOF helicopter
system is a benchmark laboratory model having strongly nonlinear
characteristics and unstable dynamics which make the control of such
system a challenging task. This article first presents the mathematical
model of the 3DOF helicopter system and then illustrates the basic
idea and technical formulation for controller design. The paper
explains the simple approach for the approximation of PID design
parameters from the LQR controller gain matrix. The simulation
results show that the investigated controller has both static and
dynamic performance, therefore the stability and the quick control
effect can be obtained simultaneously for the 3DOF helicopter
system.
Abstract: In this paper, genetic algorithm (GA) opmization technique is applied to design Flexible AC Transmission System (FACTS)-based damping controllers. Two types of controller structures, namely a proportional-integral (PI) and a lead-lag (LL) are considered. The design problem of the proposed controllers is formulated as an optimization problem and GA is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. The proposed controllers are tested on a weakly connected power system subjected to different disturbances. The non-linear simulation results are presented to show the effectiveness of the proposed controller and their ability to provide efficient damping of low frequency oscillations. It is also observed that the proposed SSSC-based controllers improve greatly the voltage profile of the system under severe disturbances. Further, the dynamic performances of both the PI and LL structured FACTS-controller are analyzed at different loading conditions and under various disturbance condition as well as under unbalanced fault conditions..
Abstract: This paper presents a systematic approach for
designing Static Synchronous Series Compensator (SSSC) based
supplementary damping controllers for damping low frequency
oscillations in a single-machine infinite-bus power system. The
design problem of the proposed controller is formulated as an
optimization problem and RCGA is employed to search for optimal
controller parameters. By minimizing the time-domain based
objective function, in which the deviation in the oscillatory rotor
speed of the generator is involved; stability performance of the
system is improved. Simulation results are presented and compared
with a conventional method of tuning the damping controller
parameters to show the effectiveness and robustness of the proposed
design approach.
Abstract: In this paper, we focus on the use of knowledge bases
in two different application areas – control of systems with unknown
or strongly nonlinear models (i.e. hardly controllable by the classical
methods), and robot motion planning in eight directions. The first
one deals with fuzzy logic and the paper presents approaches for
setting and aggregating the rules of a knowledge base. Te second one
is concentrated on a case-based reasoning strategy for finding the
path in a planar scene with obstacles.
Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: This paper, a simple continuous conduction mode (CCM) pulse-width-modulated (PWM) controller for high power factor boost converters is introduced. The duty ratios were obtained by the comparison of a sensed signal from inductor current or switch current and a negative slope ramp carrier waveform in each switching period. Due to the proposed control requires only the inductor current or switch current sensor and the output voltage sensor, its circuit implementation was very simple. To verify the proposed control, the circuit experimentation of a 350 W boost converter with the proposed control was applied. From the results, the input current waveform was shaped to be closely sinusoidal, implying high power factor and low harmonics.
Abstract: A real time image-guided electroplating system is
proposed in this paper. Unlike previous electroplating systems, instead
of using the intermittent mode to electroplate 500um long copper
specimen, a CCD camera and a motion controller are used to adjust
anode-cathode distance to obtain better results. Since the image of the
gap distance is highly deteriorated due to complex chemical-electrical
operation inside the electrolyte, to determine the gap distance, an
image processing algorithm is developed and mainly based on the
entropy and energy values. In addition, the color and incidence
direction of light source are also discussed to help the image process in
this paper. From the experiment results, the specimens created by the
proposed system show better structure, better uniformity and better
finishing surface compared to those by previous intermittent
electroplating setup.
Abstract: In this paper, a Smart Home Service Robot, McBot II,
which performs mess-cleanup function etc. in house, is designed much
more optimally than other service robots. It is newly developed in
much more practical system than McBot I which we had developed
two years ago. One characteristic attribute of mobile platforms
equipped with a set of dependent wheels is their omni- directionality
and the ability to realize complex translational and rotational
trajectories for agile navigation in door. An accurate coordination of
steering angle and spinning rate of each wheel is necessary for a
consistent motion. This paper develops trajectory controller of
3-wheels omni-directional mobile robot using fuzzy azimuth estimator.
A specialized anthropomorphic robot manipulator which can be
attached to the housemaid robot McBot II, is developed in this paper.
This built-in type manipulator consists of both arms with 3 DOF
(Degree of Freedom) each and both hands with 3 DOF each. The
robotic arm is optimally designed to satisfy both the minimum
mechanical size and the maximum workspace. Minimum mass and
length are required for the built-in cooperated-arms system. But that
makes the workspace so small. This paper proposes optimal design
method to overcome the problem by using neck joint to move the arms
horizontally forward/backward and waist joint to move them
vertically up/down. The robotic hand, which has two fingers and a
thumb, is also optimally designed in task-based concept. Finally, the
good performance of the developed McBot II is confirmed through
live tests of the mess-cleanup task.
Abstract: This paper presents Simulation and experimental
study aimed at investigating the effectiveness of an adaptive artificial
neural network stabilizer on enhancing the damping torque of a
synchronous generator. For this purpose, a power system comprising
a synchronous generator feeding a large power system through a
short tie line is considered. The proposed adaptive neuro-control
system consists of two multi-layered feed forward neural networks,
which work as a plant model identifier and a controller. It generates
supplementary control signals to be utilized by conventional
controllers. The details of the interfacing circuits, sensors and
transducers, which have been designed and built for use in tests, are
presented. The synchronous generator is tested to investigate the
effect of tuning a Power System Stabilizer (PSS) on its dynamic
stability. The obtained simulation and experimental results verify the
basic theoretical concepts.
Abstract: This paper presents a wrap-around view system with 4
smart cameras module and remote motion mobile robot control equipped with smart camera module system. The two-level scheme for
remote motion control with smart-pad(IPAD) is introduced on this
paper. In the low-level, the wrap-around view system is controlled or operated to keep the reference points lying around top view image
plane. On the higher level, a robot image based motion controller is utilized to drive the mobile platform to reach the desired position or
track the desired motion planning through image feature feedback. The
design wrap-around view system equipped on presents such advantages as follows: 1) a satisfactory solution for the FOV and affine
problem; 2) free of any complex and constraint with robot pose. The performance of the wrap-around view equipped on mobile robot
remote control is proven by experimental results.
Abstract: A multivariable discontinuous feedback linearization approach is proposed to position control of an electrically driven fast robot manipulator. A desired performance is achieved by selecting a useful controller and suitable sampling rate and considering saturation for actuators. There is a high flexibility to apply the proposed control approach on different electrically driven manipulators. The control approach can guarantee the stability and satisfactory tracking performance. A PUMA 560 robot driven by geared permanent magnet dc motors is simulated. The simulation results show a desired performance for control system under technical specifications.
Abstract: A glider is in essence an unpowered vehicle and in this project we designed and built an oceanic glider, designed to operate underwater. This Glider was designed to collect ocean data such as temperature, pressure and (in future measures physical dimensions of the operating environment) and output this data to an external source. Development of the Oceanic Glider required research into various actuation systems that control buoyancy, pitch and yaw and the dynamics of these systems. It also involved the design and manufacture of the Glider and the design and implementation of a controller that enabled the Glider to navigate and move in an appropriate manner.
Abstract: Quality of 2D and 3D cross-sectional images produce
by Computed Tomography primarily depend upon the degree of
precision of primary and secondary X-Ray intensity detection.
Traditional method of primary intensity detection is apt to errors.
Recently the X-Ray intensity measurement system along with smart
X-Ray sensors is developed by our group which is able to detect
primary X-Ray intensity unerringly. In this study a new smart X-Ray
sensor is developed using Light-to-Frequency converter TSL230
from Texas Instruments which has numerous advantages in terms of
noiseless data acquisition and transmission. TSL230 construction is
based on a silicon photodiode which converts incoming X-Ray
radiation into the proportional current signal. A current to frequency
converter is attached to this photodiode on a single monolithic CMOS
integrated circuit which provides proportional frequency count to
incoming current signal in the form of the pulse train. The frequency
count is delivered to the center of PICDEM FS USB board with
PIC18F4550 microcontroller mounted on it. With highly compact
electronic hardware, this Demo Board efficiently read the smart
sensor output data. The frequency output approaches overcome
nonlinear behavior of sensors with analog output thus un-attenuated
X-Ray intensities could be measured precisely and better
normalization could be acquired in order to attain high resolution.