Abstract: As the trend in automotive technology is fast moving
towards hybridization and electrification to curb emissions as well as
to improve the fuel efficiency, air-conditioning systems in passenger
cars have not caught up with this trend and still remain as the major
energy consumers amongst others. Adsorption based air-conditioning
systems, e.g. with silica-gel water pair, which are already in use for
residential and commercial applications, are now being considered as
a technology leap once proven feasible for the passenger cars. In this
paper we discuss a methodology, challenges and feasibility of
implementing an adsorption based air-conditioning system in a
passenger car utilizing the exhaust waste heat. We also propose an
optimized control strategy with interfaces to the engine control unit
of the vehicle for operating this system with reasonable efficiency
supported by our simulation and validation results in a prototype
vehicle, additionally comparing to existing implementations,
simulation based as well as experimental. Finally we discuss the
influence of start-stop and hybrid systems on the operation strategy of
the adsorption air-conditioning system.
Abstract: This work sets out to debate the tensions involved in
the processes of contamination and self-purification in the urban
space, particularly in the streams that run through the Buenos Aires
metropolitan area. For much of their course, those streams are piped;
their waters do not come into contact with the outdoors until they
have reached deeply impoverished urban areas with high levels of
environmental contamination. These are peripheral zones that, until
thirty years ago, were marshlands and fields. They are now densely
populated areas largely lacking in urban infrastructure.
The Cárcova neighborhood, where this project is underway, is in
the José León Suárez section of General San Martín county, Buenos
Aires province. A stretch of José León Suarez canal crosses the
neighborhood. Starting upstream, this canal carries pollutants due to
the sewage and industrial waste released into it. Further downstream,
in the neighborhood, domestic drainage is poured into the stream. In
this paper, we formulate a hypothesis diametrical to the one that
holds that these neighborhoods are the primary source of
contamination, suggesting instead that in the stretch of the canal that
runs through the neighborhood the stream’s waters are actually
cleaned and the sediments accumulate pollutants. Indeed, the
stretches of water that runs through these neighborhoods act as water
processing plants for the metropolis.
This project has studied the different organic-load polluting
contributions to the water in a certain stretch of the canal, the
reduction of that load over the course of the canal, and the
incorporation of pollutants into the sediments. We have found that
the surface water has considerable ability to self-purify, mostly due to
processes of sedimentation and adsorption. The polluting load is
accumulated in the sediments where that load stabilizes slowly by
means of anaerobic processes. In this study, we also investigated the
risks of sediment management and the use of the processes studied
here in controlled conditions as tools of environmental restoration.
Abstract: Activated carbon is an amorphous carbon chain which
has extremely extended surface area. High surface area of activated
carbon is due to the porous structure. Activated carbon, using a
variety of materials such as coal and cellulosic materials; can be
obtained by both physical and chemical methods. The prepared
activated carbon can be used for decolorize, deodorize and also can
be used for removal of organic and non-organic pollution. In this
study, pomegranate peel was subjected to 800W microwave power
for 1 to 4 minutes. Also fresh pomegranate peel was used for the
reference material. Then ZnCl2 was used for the chemical activation
purpose. After the activation process, activated pomegranate peels
were used for the adsorption of Zn metal (40 ppm) in the waste water.
As a result of the adsorption experiments, removal of heavy metals
ranged from 89% to 85%.
Abstract: Silica was extracted from agriculture waste rice husk
ash (RHA) and was used as the silica source for synthesis of
RMCM-48 and RSBA-16. An alkali fusion process was utilized to
separate silicate supernatant and the sediment effectively. The
CTAB/Si and F127/Si molar ratio was employed to control the
structure properties of the obtained RMCM-48 and RSBA-16
materials. The N2 adsorption-desorption results showed the
micro-mesoporous RSBA-16 possessed high specific surface areas
(662-1001 m2/g). All the obtained RSBA-16 materials were applied as
the adsorbents for acetone adsorption. And the breakthrough tests
clearly revealed that the RSBA-16(0.004) materials could achieve the
highest acetone adsorption capacity of 181 mg/g under 1000 ppmv
acetone vapor concentration at 25oC, which was also superior to
ZSM-5 (71mg/g) and MCM-41 (157mg/g) under same test conditions.
This can help to reduce the solid waste and the high adsorption
performance of the obtained materials could consider as potential
adsorbents for acetone adsorption.
Abstract: Activated carbons (M4P0, M4P2, and M5P2) used in
this research were produced from palm shell and polyetherether
ketone (PEEK) via carbonization, impregnation and microwave
activation. The adsorption/desorption process was carried out using
static volumetric adsorption. Regeneration is important in the overall
economy of the process and waste minimization. This work focuses
on the thermal regeneration of the CO2 exhausted microwave
activated carbons. The regeneration strategy adopted was thermal
with nitrogen purge desorption with N2 feed flow rate of 20 ml/min
for 1 h at atmospheric pressure followed by drying at 150oC.Seven
successive adsorption/regeneration processes were carried out on the
material. It was found that after seven adsorption regeneration cycles;
the regeneration efficiency (RE) for CO2 activated carbon from palm
shell only (M4P0) was more than 90% while that of hybrid palm
shell-PEEK (M4P2, M5P2) was above 95%. The cyclic adsorption
and regeneration shows the stability of the adsorbent materials.
Abstract: Surface modification and functionalization has been
an important tool for scientists in order to open new frontiers in
nanoscience and nanotechnology. Desired surface characteristics for
the intended applications can be achieved with surface
functionalization.
In this work, the effect of water soluble ligands on the adsorption
capabilities of silver nanoparticles onto AC which was synthesized
from German beech wood was investigated. Sodium borohydride
(NaBH4) and polyvinyl alcohol (PVA) were used as the ligands.
Silver nanoparticles with different surface coatings have average
sizes range from 10 to 13 nm. They were synthesized in aqueous
media by reducing Ag (I) ion in the presence of ligands. These
particles displayed adsorption tendencies towards AC when they
were mixed together and shaken in distilled water.
Silver nanoparticles (NaBH4-AgNPs) reduced and stabilized by
NaBH4 adsorbed onto AC with a homogenous dispersion of
aggregates with sizes in the range of 100-400 nm. Beside, silver
nanoparticles, which were prepared in the presence of both NaBH4
and PVA (NaBH4/PVA-Ag NPs), demonstrated that NaBH4/PVA-Ag
NPs adsorbed and dispersed homogenously but, they aggregated with
larger sizes on the AC surface (range from 300 to 600 nm). In
addition, desorption resistance of Ag nanoparticles were investigated
in distilled water. According to the results AgNPs were not desorbed
on the AC surface in distilled water.
Abstract: Polycyclic aromatic hydrocarbons (PAHs) are formed
during the pyrolysis of scrap tyres to produce tyre pyrolytic oil
(TPO). Due to carcinogenic, mutagenic, and toxic properties PAHs
are priority pollutants. Hence it is essential to remove PAHs from
TPO before utilising TPO as a petroleum fuel alternative (to run the
engine). Agricultural wastes have promising future to be utilized as
biosorbent due to their cost effectiveness, abundant availability, high
biosorption capacity and renewability. Various low cost adsorbents
were prepared from natural sources. Uptake of PAHs present in tyre
pyrolytic oil was investigated using various low-cost adsorbents of
natural origin including sawdust (shisham), coconut fiber, neem bark,
chitin, activated charcoal. Adsorption experiments of different PAHs
viz. naphthalene, acenaphthalene, biphenyl and anthracene have been
carried out at ambient temperature (25°C) and at pH 7. It was
observed that for any given PAH, the adsorption capacity increases
with the lignin content. Freundlich constant Kf and 1/n have been
evaluated and it was found that the adsorption isotherms of PAHs
were in agreement with a Freundlich model, while the uptake
capacity of PAHs followed the order: activated charcoal> saw dust
(shisham) > coconut fiber > chitin. The partition coefficients in
acetone-water, and the adsorption constants at equilibrium, could be
linearly correlated with octanol–water partition coefficients. It is
observed that natural adsorbents are good alternative for PAHs
removal. Sawdust of Dalbergia sissoo, a by-product of sawmills was
found to be a promising adsorbent for the removal of PAHs present in
TPO. It is observed that adsorbents studied were comparable to those
of some conventional adsorbents.
Abstract: A quartz crystal microbalance (QCM) nanosensor was developed to detect lysozyme enzyme by functionalizing its gold surface with the attachment of poly(methacroyl-L-phenylalanine) (PMAPA) nanoparticles. PMAPA was chosen as a hydrophobic matrix. The hydrophobic nanoparticles were synthesized by micro-emulsion polymerization method. Hydrophobic QCM nanosensor was tested for real time detection of lysozyme enzyme from aqueous solution. The kinetic and affinity studies were determined by using lysozyme solutions with different concentrations. The responses related with mass (Δm) and frequency (Δf) shifts were used to evaluate adsorption properties.
Abstract: In this article a comparison was made between Cu and
TiO2 supported catalysts on activated carbon for ozone
decomposition reaction. The activated carbon support in the case of
TiO2/AC sample was prepared by physicochemical pyrolysis and for
Cu/AC samples the supports are chemically modified carbons. The
prepared catalysts were synthesized by impregnation method. The
samples were annealed in two different regimes- in air and under
vacuum. To examine adsorption efficiency of the samples BET
method was used. All investigated catalysts supported on chemically
modified carbons have higher specific surface area compared to the
specific surface area of TiO2 supported catalysts, varying in the range
590÷620 m2/g. The method of synthesis of the precursors had
influenced catalytic activity.
Abstract: In this study, we have focused our attention on
combining of molecular imprinting into nanofilms and QCM
nanosensor approaches and producing QCM nanosensor for anti-
CCP, chosen as model protein, using anti-CCP imprinted nanofilms.
The nonimprinted nanosensor was also prepared to evaluate the
selectivity of the imprinted nanosensor. Anti-CCP imprinted QCM
nanosensor was tested for real time detection of anti-CCP from
aqueous solution. The kinetic and affinity studies were determined by
using anti-CCP solutions with different concentrations. The
responses related with mass shifts (%m) and frequency shifts (%f)
were used to evaluate adsorption properties. To show the selectivity
of the anti-CCP imprinted QCM nanosensor, competitive adsorption
of anti-CCP and IgM was investigated. The results indicate that anti-
CCP imprinted QCM nanosensor has higher adsorption capabilities
for anti-CCP than for IgM, due to selective cavities in the polymer
structure.
Abstract: The adsorption efficiency of fired clayey pellets of 5
and 8 mm diameter size for Cu(II) and Zn(II) ion removal from a
waste printing developer was studied. In order to investigate the
influence of contact time, adsorbent mass and pellet size on the
adsorption efficiency the batch mode was carried out. Faster uptake
of copper ion was obtained with the fired clay pellets of 5 mm
diameter size within 30 minutes. The pellets of 8 mm diameter size
showed the higher equilibrium time (60 to 75 minutes) for copper and
zinc ion. The results pointed out that adsorption efficiency increases
with the increase of adsorbent mass. The maximal efficiency is
different for Cu(II) and Zn(II) ion due to the pellet size. Therefore,
the fired clay pellets of 5 mm diameter size present an effective
adsorbent for Cu(II) ion removal (adsorption efficiency is 63.6%),
whereas the fired clay pellets of 8 mm diameter size are the best
alternative for Zn(II) ion removal (adsorption efficiency is 92.8%)
from a waste printing developer.
Abstract: Adsorption of a boron nitride nanotube (BNNT) was
examined toward ethylacetylene (C4H6) molecule by using density
functional theory (DFT) calculations at the B3LYP/6-31G (d) level,
and it was found that the adsorption energy (Ead) of ethylacetylene
the pristine nanotubes is about -1.60kcal/mol. But when nanotube has
been doped with Si and Al atoms, the adsorption energy of
ethylacetylene molecule was increased. Calculation showed that
when the nanotube is doping by Al, the adsorption energy is about -
24.19kcal/mol and also the amount of HOMO/LUMO energy gap
(Eg) will reduce significantly. Boron nitride nanotube is a suitable
adsorbent for ethylacetylene and can be used in separation processes
ethylacetylene. It is seem that nanotube (BNNT) is a suitable
semiconductor after doping, and the doped BNNT in the presence of
ethylacetylene an electrical signal is generating directly and therefore
can potentially be used for ethylacetylene sensors.
Abstract: In this work, a polyaniline/Iron oxide (PANI/Fe2O3)
composite was chemically prepared by oxidative polymerization of
aniline in acid medium, in presence of ammonium persulphate as an
oxidant and amount of Fe2O3. The composite was characterized by a
scanning electron microscopy (SEM). The prepared composite has
been used as adsorbent to remove Tartrazine dye form aqueous
solutions.
The effects of initial dye concentration and temperature on the
adsorption capacity of PANI/Fe2O3 for Tartrazine dye have been
studied in this paper.
The Langmuir and Freundlich adsorption models have been used
for the mathematical description of adsorption equilibrium data. The
best fit is obtained using the Freundlich isotherm with an R2 value of
0.998. The change of Gibbs energy, enthalpy, and entropy of
adsorption has been also evaluated for the adsorption of Tartrazine
onto PANI/ Fe2O3. It has been proved according the results that the
adsorption process is endothermic in nature.
Abstract: Preparation of nanoparticles of cerium oxide and
adsorption of bovine serum albumin on them were studied. Particle
size distribution and influence of pH on zeta potential of prepared
CeO2 were determined. Average size of prepared cerium oxide
nanoparticles was 9 nm. The simultaneous measurements of the
bovine serum albumin adsorption and zeta potential determination of
the (adsorption) suspensions were carried out. The adsorption
isotherms were found to be of typical Langmuir type; values of the
bovine serum albumin adsorption capacities were calculated.
Increasing of pH led to decrease of zeta potential and decrease of
adsorption capacity of cerium oxide nanoparticles. The maximum
adsorption capacity was found for strongly acid suspension (am =
118 mg/g). The samples of nanoceria with positive zeta potential
adsorbed more bovine serum albumin on the other hand, the samples
with negative zeta potential showed little or no protein adsorption.
Surface charge or better say zeta potential of CeO2 nanoparticles
plays the key role in adsorption of proteins on such type of materials.
Abstract: Multiwall carbon nanotubes, prepared by chemical
vapor deposition, have an average diameter of 60-100 nm as shown
by High Resolution Transmittance Electron Microscope, HR-TEM.
The Multiwall carbon nanotubes (MWCNTs) were further
characterized using X-ray Diffraction and Raman Spectroscopy.
Mercury uptake capacity of MWCNTs was studied using batch
adsorption method at different concentration ranges up to 150 ppm.
Mercury concentration (before and after the treatment) was measured
using cold vapor atomic absorption spectroscopy. The effect of time,
concentration, pH and adsorbent dose were studied. MWCNT were
found to perform complete absorption in the sub-ppm concentrations
(parts per billion levels) while for high concentrations, the adsorption
efficiency was 92% at the optimum conditions; 0.1 g of the adsorbent
at 150 ppm mercury (II) solution. The adsorption of mercury on
MWCNTs was found to follow the Freundlich adsorption isotherm
and the pseudo-second order kinetic model.
Abstract: This study was conducted to evaluate the manganese
removal from aqueous solution using Banana peels activated carbon
(BPAC). Batch experiments have been carried out to determine the
influence of parameters such as pH, biosorbent dose, initial metal ion
concentrations and contact times on the biosorption process. From
these investigations, a significant increase in percentage removal of
manganese 97.4% is observed at pH value 5.0, biosorbent dose 0.8 g,
initial concentration 20 ppm, temperature 25 ± 2°C, stirring rate 200
rpm and contact time 2h. The equilibrium concentration and the
adsorption capacity at equilibrium of the experimental results were
fitted to the Langmuir and Freundlich isotherm models; the Langmuir
isotherm was found to well represent the measured adsorption data
implying BPAC had heterogeneous surface. A raw groundwater
samples were collected from Baharmos groundwater treatment plant
network at Embaba and Manshiet Elkanater City/District-Giza,
Egypt, for treatment at the best conditions that reached at first phase
by BPAC. The treatment with BPAC could reduce iron and
manganese value of raw groundwater by 91.4% and 97.1%,
respectively and the effect of the treatment process on the
microbiological properties of groundwater sample showed decrease
of total bacterial count either at 22°C or at 37°C to 85.7% and 82.4%,
respectively. Also, BPAC was characterized using SEM and FTIR
spectroscopy.
Abstract: Calcium phosphate coating (CaP) has been employed
for protein delivery, but the typical direct protein adsorption on the
coating led to low incorporation content and fast release of the
protein from the coating. By using bovine serum albumin (BSA) as a
model protein, rapid biomimetic co-precipitation between calcium
phosphate and BSA was employed to control the distribution of BSA
within calcium phosphate coating during biomimetic formation on
titanium surface for only 6 h at 50oC in an accelerated calcium
phosphate solution. As a result, the amount of BSA incorporation and
release duration could be increased by using a rapid biomimetic coprecipitation
technique. Up to 43 fold increases in the BSA
incorporation content and the increase from 6 h to more than 360 h in
release duration compared to typical direct adsorption technique were
observed depending on the initial BSA concentration used during coprecipitation
(1, 10 and 100 μg.ml-1). From x-ray diffraction and
Fourier transform infrared spectroscopy studies, the coating
composition was not altered with the incorporation of BSA by this
rapid biomimetic co-precipitation and mainly comprised octacalcium
phosphate and hydroxyapatite. However, the microstructure of
calcium phosphate crystals changed from straight, plate-like units to
curved, plate-like units with increasing BSA content.
Abstract: The mineral bioflotation represents a viable
alternative for the evaluation of new processes benefit alternative.
The adsorption bacteria on minerals surfaces will depend mainly on
the type of the microorganism as well as of the studied mineral
surface. In the current study, adhesion of S. carnosus on coal was
studied. Several methods were used as: DRX, Fourier Transform
Infra-Red (FTIR) adhesion isotherms and kinetic. The main goal is to
recovery of organic matter by the microflotation process on coal
particles with biological reagent (S. carnosus). Adhesion tests
revealed that adhesion took place after of 8 h at pH 9. The results
suggest that the adhesion of bacteria to solid substrates can be
considered an abiotic physicochemical process that is consequently
governed by bacterial surface properties such as their specific surface
area, hydrophobicity and surface functionalities. The greatest coal
fine flotability was of 75%, after 5 min of flotation.
Abstract: Fly ash is an important waste, produced in thermal
power plants which causes very important environmental pollutions.
For this reason the usage and evaluation the fly ash in various areas
are very important. Nearly, 15 million tons/year of fly ash is
produced in Turkey. In this study, usage of fly ash with diatomite and
molasses for heavy metal (Cd) adsorption from wastewater is
investigated. The samples of Seyitomer region fly ash were analyzed
by X-ray fluorescence (XRF) and Scanning Electron Microscope
(SEM) then diatomite (0 and 1% in terms of fly ash, w/w) and
molasses (0-0.75 mL) were pelletized under 30 MPa of pressure for
the usage of cadmium (Cd) adsorption in wastewater. After the
adsorption process, samples of Seyitomer were analyzed using
Optical Emission Spectroscopy (ICP-OES). As a result, it is seen that
the usage of Seyitomer fly ash is proper for cadmium (Cd) adsorption
and an optimum adsorption yield with 52% is found at a compound
with Seyitomer fly ash (10 g), diatomite (0.5 g) and molasses (0.75
mL) at 2.5 h of reaction time, pH:4, 20ºC of reaction temperature and
300 rpm of stirring rate.
Abstract: The study investigated the implementation of the
Neural Network (NN) techniques for prediction of the loading of Cu
ions onto clinoptilolite. The experimental design using analysis of
variance (ANOVA) was chosen for testing the adequacy of the
Neural Network and for optimizing of the effective input parameters
(pH, temperature and initial concentration). Feed forward, multi-layer
perceptron (MLP) NN successfully tracked the non-linear behavior of
the adsorption process versus the input parameters with mean squared
error (MSE), correlation coefficient (R) and minimum squared error
(MSRE) of 0.102, 0.998 and 0.004 respectively. The results showed
that NN modeling techniques could effectively predict and simulate
the highly complex system and non-linear process such as ionexchange.