Abstract: This paper presents the use of anti-sway angle control
approaches for a two-dimensional gantry crane with disturbances
effect in the dynamic system. Delayed feedback signal (DFS) and
proportional-derivative (PD)-type fuzzy logic controller are the
techniques used in this investigation to actively control the sway
angle of the rope of gantry crane system. A nonlinear overhead
gantry crane system is considered and the dynamic model of the
system is derived using the Euler-Lagrange formulation. A complete
analysis of simulation results for each technique is presented in time
domain and frequency domain respectively. Performances of both
controllers are examined in terms of sway angle suppression and
disturbances cancellation. Finally, a comparative assessment of the
impact of each controller on the system performance is presented and
discussed.
Abstract: A mathematical model for the Dynamics of Economic
Profit is constructed by proposing a characteristic differential oneform
for this dynamics (analogous to the action in Hamiltonian
dynamics). After processing this form with exterior calculus, a pair of
characteristic differential equations is generated and solved for the
rate of change of profit P as a function of revenue R (t) and cost C (t).
By contracting the characteristic differential one-form with a vortex
vector, the Lagrangian is obtained for the Dynamics of Economic
Profit.
Abstract: The paper presents a simple and an accurate formula
that has been developed for the conduction angle (δ) of a single
phase half-wave or full-wave controlled rectifier with RL load. This
formula can be also used for calculating the conduction angle (δ) in
case of A.C. voltage regulator with inductive load under
discontinuous current mode. The simulation results shows that the
conduction angle calculated from the developed formula agree very
well with that obtained from the exact solution arrived from the
iterative method. Applying the developed formula can reduce the
computational time and reduce the time for manual classroom
calculation. In addition, the proposed formula is attractive for real
time implementations.
Abstract: Due to the stringent legislation for emission of diesel
engines and also increasing demand on fuel consumption, the
importance of detailed 3D simulation of fuel injection, mixing and
combustion have been increased in the recent years. In the present
work, FIRE code has been used to study the detailed modeling of
spray and mixture formation in a Caterpillar heavy-duty diesel
engine. The paper provides an overview of the submodels
implemented, which account for liquid spray atomization, droplet
secondary break-up, droplet collision, impingement, turbulent
dispersion and evaporation. The simulation was performed from
intake valve closing (IVC) to exhaust valve opening (EVO). The
predicted in-cylinder pressure is validated by comparing with
existing experimental data. A good agreement between the predicted
and experimental values ensures the accuracy of the numerical
predictions collected with the present work. Predictions of engine
emissions were also performed and a good quantitative agreement
between measured and predicted NOx and soot emission data were
obtained with the use of the present Zeldowich mechanism and
Hiroyasu model. In addition, the results reported in this paper
illustrate that the numerical simulation can be one of the most
powerful and beneficial tools for the internal combustion engine
design, optimization and performance analysis.
Abstract: The study of a real function of two real variables can be supported by visualization using a Computer Algebra System (CAS). One type of constraints of the system is due to the algorithms implemented, yielding continuous approximations of the given function by interpolation. This often masks discontinuities of the function and can provide strange plots, not compatible with the mathematics. In recent years, point based geometry has gained increasing attention as an alternative surface representation, both for efficient rendering and for flexible geometry processing of complex surfaces. In this paper we present different artifacts created by mesh surfaces near discontinuities and propose a point based method that controls and reduces these artifacts. A least squares penalty method for an automatic generation of the mesh that controls the behavior of the chosen function is presented. The special feature of this method is the ability to improve the accuracy of the surface visualization near a set of interior points where the function may be discontinuous. The present method is formulated as a minimax problem and the non uniform mesh is generated using an iterative algorithm. Results show that for large poorly conditioned matrices, the new algorithm gives more accurate results than the classical preconditioned conjugate algorithm.
Abstract: DNA shuffling is a powerful method used for in vitro
evolute molecules with specific functions and has application in areas
such as, for example, pharmaceutical, medical and agricultural
research. The success of such experiments is dependent on a variety
of parameters and conditions that, sometimes, can not be properly
pre-established. Here, two computational models predicting DNA
shuffling results is presented and their use and results are evaluated
against an empirical experiment. The in silico and in vitro results
show agreement indicating the importance of these two models and
motivating the study and development of new models.
Abstract: The main goal of this paper is to study Statistical Process Control (SPC) with Exponentially Weighted Moving Average (EWMA) control chart when observations are serially-correlated. The characteristic of control chart is Average Run Length (ARL) which is the average number of samples taken before an action signal is given. Ideally, an acceptable ARL of in-control process should be enough large, so-called (ARL0). Otherwise it should be small when the process is out-of-control, so-called Average of Delay Time (ARL1) or a mean of true alarm. We find explicit formulas of ARL for EWMA control chart for Seasonal Autoregressive and Moving Average processes (SARMA) with Exponential white noise. The results of ARL obtained from explicit formula and Integral equation are in good agreement. In particular, this formulas for evaluating (ARL0) and (ARL1) be able to get a set of optimal parameters which depend on smoothing parameter (λ) and width of control limit (H) for designing EWMA chart with minimum of (ARL1).
Abstract: The aim of this research is to use artificial neural networks computing technology for estimating the net heating value (NHV) of crude oil by its Properties. The approach is based on training the neural network simulator uses back-propagation as the learning algorithm for a predefined range of analytically generated well test response. The network with 8 neurons in one hidden layer was selected and prediction of this network has been good agreement with experimental data.
Abstract: The spiral angle of the elementary cellulose fibril in
the wood cell wall, often called microfibril angle, (MFA). Microfibril
angle in hardwood is one of the key determinants of solid timber
performance due to its strong influence on the stiffness, strength,
shrinkage, swelling, thermal-dynamics mechanical properties and
dimensional stability of wood. Variation of MFA (degree) in the S2
layer of the cell walls among Acacia mangium trees was determined
using small-angle X-ray scattering (SAXS). The length and
orientation of the microfibrils of the cell walls in the irradiated
volume of the thin samples are measured using SAXS and optical
microscope for 3D surface measurement. The undetermined
parameters in the analysis are the MFA, (M) and the standard
deviation (σФ) of the intensity distribution arising from the wandering
of the fibril orientation about the mean value. Nine separate pairs of
values are determined for nine different values of the angle of the
incidence of the X-ray beam relative to the normal to the radial
direction in the sample. The results show good agreement. The
curve distribution of scattered intensity for the real cell wall structure
is compared with that calculated with that assembly of rectangular
cells with the same ratio of transverse to radial cell wall length. It is
demonstrated that for β = 45°, the peaks in the curve intensity
distribution for the real and the rectangular cells coincide. If this
peak position is Ф45, then the MFA can be determined from the
relation M = tan-1 (tan Ф45 / cos 45°), which is precise for rectangular
cells. It was found that 92.93% of the variation of MFA can be
attributed to the distance from pith to bark. Here we shall present our
results of the MFA in the cell wall with respect to its shape, structure
and the distance from pith to park as an important fast check and yet
accurate towards the quality of wood, its uses and application.
Abstract: The Internet is the global data communications
infrastructure based on the interconnection of both public and private
networks using protocols that implement Internetworking on a global
scale. Hence the control of protocol and infrastructure development,
resource allocation and network operation are crucial and interlinked
aspects. Internet Governance is the hotly debated and contentious
subject that refers to the global control and operation of key Internet
infrastructure such as domain name servers and resources such as
domain names. It is impossible to separate technical and political
positions as they are interlinked. Furthermore the existence of a
global market, transparency and competition impact upon Internet
Governance and related topics such as network neutrality and
security. Current trends and developments regarding Internet
governance with a focus on the policy-making process, security and
control have been observed to evaluate current and future
implications on the Internet. The multi stakeholder approach to
Internet Governance discussed in this paper presents a number of
opportunities, issues and developments that will affect the future
direction of the Internet. Internet operation, maintenance and
advisory organisations such as the Internet Corporation for Assigned
Names and Numbers (ICANN) or the Internet Governance Forum
(IGF) are currently in the process of formulating policies for future
Internet Governance. Given the controversial nature of the issues at
stake and the current lack of agreement it is predicted that
institutional as well as market governance will remain present for the
network access and content.
Abstract: Series of tellurite glass of the system 78TeO2-10PbO-
10Li2O-(2-x)Nd2O3-xEr2O3, where x = 0.5, 1.0, 1.5 and 2.0 was
successfully been made. A study of upconversion luminescence of
the Nd3+/Er3+ co-doped tellurite glass has been carried out. From
Judd-Ofelt analysis, the experimental lifetime, exp. τ of the glass
serie are found higher in the visible region as they varies from
65.17ms to 114.63ms, whereas in the near infrared region (NIR) the
lifetime are varies from 2.133ms to 2.270ms. Meanwhile, the
emission cross section,σ results are found varies from 0.004 x 1020
cm2 to 1.007 x 1020 cm2 with respect to composition. The emission
spectra of the glass are found been contributed from Nd3+ and Er3+
ions by which nine significant transition peaks are observed. The
upconversion mechanism of the co-doped tellurite glass has been
shown in the schematic energy diagrams. In this works, it is found
that the excited state-absorption (ESA) is still dominant in the
upconversion excitation process as the upconversion excitation
mechanism of the Nd3+ excited-state levels is accomplished through a
stepwise multiphonon process. An efficient excitation energy transfer
(ET) has been observed between Nd3+ as a donor and Er3+ as the
acceptor. As a result, respective emission spectra had been observed.
Abstract: In this study, active tendons with Proportional Integral
Derivation type controllers were applied to a SDOF and a MDOF
building model. Physical models of buildings were constituted with
virtual springs, dampers and rigid masses. After that, equations of
motion of all degrees of freedoms were obtained. Matlab Simulink
was utilized to obtain the block diagrams for these equations of
motion. Parameters for controller actions were found by using a trial
method. After earthquake acceleration data were applied to the
systems, building characteristics such as displacements, velocities,
accelerations and transfer functions were analyzed for all degrees of
freedoms. Comparisons on displacement vs. time, velocity vs. time,
acceleration vs. time and transfer function (Db) vs. frequency (Hz)
were made for uncontrolled and controlled buildings. The results
show that the method seems feasible.
Abstract: Business process model describes process flow of a
business and can be seen as the requirement for developing a
software application. This paper discusses a BPM2CD guideline
which complements the Model Driven Architecture concept by
suggesting how to create a platform-independent software model in
the form of a UML class diagram from a business process model. An
important step is the identification of UML classes from the business
process model. A technique for object-oriented analysis called
domain analysis is borrowed and key concepts in the business
process model will be discovered and proposed as candidate classes
for the class diagram. The paper enhances this step by using ontology
search to help identify important classes for the business domain. As
ontology is a source of knowledge for a particular domain which
itself can link to ontologies of related domains, the search can give a
refined set of candidate classes for the resulting class diagram.
Abstract: In present work, drying characteristics of fresh papaya (Carica papaya L.) was studied to understand the dehydration process and its behavior. Drying experiments were carried out by a laboratory scaled microwave-vacuum oven. The parameters affecting drying characteristics including operating modes (continuous, pulsed), microwave power (400 and 800 W), and vacuum pressure (20, 30, and 40 cmHg) were investigated. For pulsed mode, two levels of power-off time (60 and 120 s) were used while the power-on time was fixed at 60 s and the vacuum pressure was fixed at 40 cmHg. For both operating modes, the effects of drying conditions on drying time, drying rate, and effective diffusivity were investigated. The results showed high microwave power, high vacuum, and pulsed mode of 60 s-on/60 s-off favored drying rate as shown by the shorten drying time and increased effective diffusivity. The drying characteristics were then described by Page-s model, which showed a good agreement with experimental data.
Abstract: Environmental factors affect agriculture production
productivity and efficiency resulted in changing of profit efficiency.
This paper attempts to estimate the impacts of environmental factors
to profitability of rice farmers in the Red River Delta of Vietnam. The
dataset was extracted from 349 rice farmers using personal
interviews. Both OLS and MLE trans-log profit functions were used
in this study. Five production inputs and four environmental factors
were included in these functions. The estimation of the stochastic
profit frontier with a two-stage approach was used to measure
profitability. The results showed that the profit efficiency was about
75% on the average and environmental factors change profit
efficiency significantly beside farm specific characteristics. Plant
disease, soil fertility, irrigation apply and water pollution were the
four environmental factors cause profit loss in rice production. The
result indicated that farmers should reduce household size, farm
plots, apply row seeding technique and improve environmental
factors to obtain high profit efficiency with special consideration is
given for irrigation water quality improvement.
Abstract: Heat powered solid sorption is a feasible alternative to
electrical vapor compression refrigeration systems. In this paper,
activated carbon (powder type Maxsorb and fiber type ACF-A10)-
CO2 based adsorption cooling cycles are studied using the pressuretemperature-
concentration (P-T-W) diagram. The specific cooling
effect (SCE) and the coefficient of performance (COP) of these two
cooling systems are simulated for the driving heat source
temperatures ranging from 30 ºC to 90 ºC in terms of different
cooling load temperatures with a cooling source temperature of 25
ºC. It is found from the present analysis that Maxsorb-CO2 couple
shows higher cooling capacity and COP. The maximum COPs of
Maxsorb-CO2 and ACF(A10)-CO2 based cooling systems are found
to be 0.15 and 0.083, respectively. The main innovative feature of
this cooling cycle is the ability to utilize low temperature waste heat
or solar energy using CO2 as the refrigerant, which is one of the best
alternative for applications where flammability and toxicity are not
allowed.
Abstract: In this research, an aerobic composting method is
studied to reuse organic waste from rubber factory waste as soil fertilizer and to study the effect of cellulolytic microbial activator
(CMA) as the activator in the rubber factory waste composting. The
performance of the composting process was monitored as a function
of carbon and organic matter decomposition rate, temperature and
moisture content. The results indicate that the rubber factory waste is best composted with water hyacinth and sludge than composted
alone. In addition, the CMA is more affective when mixed with the rubber factory waste, water hyacinth and sludge since a good fertilizer is achieved. When adding CMA into the rubber factory
waste composted alone, the finished product does not achieve a
standard of fertilizer, especially the C/N ratio.
Finally, the finished products of composting rubber factory waste and water hyacinth and sludge (both CMA and without CMA), can be an environmental friendly alternative to solve the disposal problems of rubber factory waste. Since the C/N ratio, pH, moisture
content, temperature, and nutrients of the finished products are acceptable for agriculture use.
Abstract: Dengue fever is an important human arboviral disease. Outbreaks are now reported quite often from many parts of the world. The number of cases involving pregnant women and infant cases are increasing every year. The illness is often severe and complications may occur. Deaths often occur because of the difficulties in early diagnosis and in the improper management of the diseases. Dengue antibodies from pregnant women are passed on to infants and this protects the infants from dengue infections. Antibodies from the mother are transferred to the fetus when it is still in the womb. In this study, we formulate a mathematical model to describe the transmission of this disease in pregnant women. The model is formulated by dividing the human population into pregnant women and non-pregnant human (men and non-pregnant women). Each class is subdivided into susceptible (S), infectious (I) and recovered (R) subclasses. We apply standard dynamical analysis to our model. Conditions for the local stability of the equilibrium points are given. The numerical simulations are shown. The bifurcation diagrams of our model are discussed. The control of this disease in pregnant women is discussed in terms of the threshold conditions.
Abstract: The flow of a third grade fluid in an orthogonal rheometer is studied. We employ the admissible velocity field proposed in [5]. We solve the problem and obtain the velocity field as well as the components for the Cauchy tensor. We compare the results with those from [9]. Some diagrams concerning the velocity and Cauchy stress components profiles are presented for different values of material constants and compared with the corresponding values for a linear viscous fluid.
Abstract: Unified Modeling Language (UML) is a standard
language for modeling of a system. UML is used to visually specify
the structure and behavior of a system. The system requirements are
captured and then converted into UML specification. UML
specification uses a set of rules and notations, and diagrams to
specify the system requirements. In this paper, we present a tool for
developing the UML specification. The tool will ease the use of the
notations and diagrams for UML specification as well as increase the
understanding and familiarity of the UML specification. The tool will
also be able to check the conformance of the diagrams against each
other for basic compliance of UML specification.