Abstract: Deoxygenation of beef fat for the production of hydrogenated biodiesel is investigated in a high pressure continuous flow fixed bed reactor over palladium-supported mesoporous titania catalyst synthesized via a combined single-step sol-gel process with surfactant-assisted templating method (SATM). The catalyst possessed a mesoporous charactheristic with high surface area and narrow pore size distribution. The main products of all Pd/TiO2 catalysts are n-heptadecane (n-C17) and n-pentadecane (n-C15) resulting from decarbonylation reaction. Pd/TiO2 catalyst synthesized via a combined single-step sol-gel process with SATM (SSSG) gave higher activity and selectivity to the desired products when compared to IWI/SG-TiO2 and IWI/P25-TiO2, respectively. SSSG catalyst gave the average conversion up to 80-90 % and 80 % for the selectivity in diesel range hydrocarbons. This result may cause by the higher surface area and the ability in dispersion of palladium ion in mesoporous of TiO2 during sol-gel process.
Abstract: Radial flow reactor was focused for large scale
methanol synthesis and in which the heat transfer type was cross-flow.
The effects of operating conditions including the reactor inlet air
temperature, the heating pipe temperature and the air flow rate on the
cross-flow heat transfer was investigated and the results showed that
the temperature profile of the area in front of the heating pipe was
slightly affected by all the operating conditions. The main area whose
temperature profile was influenced was the area behind the heating
pipe. The heat transfer direction according to the air flow directions. In
order to provide the basis for radial flow reactor design calculation, the
dimensionless number group method was used for data fitting of the
bed effective thermal conductivity and the wall heat transfer
coefficient which was calculated by the mathematical model with the
product of Reynolds number and Prandtl number. The comparison of
experimental data and calculated value showed that the calculated
value fit the experimental data very well and the formulas could be
used for reactor designing calculation.
Abstract: Contamination of aromatic compounds in water can
cause severe long-lasting effects not only for biotic organism but also
on human health. Several alternative technologies for remediation of
polluted water have been attempted. One of these is adsorption
process of aromatic compounds by using organic modified clay
mineral. Porous structure of clay is potential properties for molecular
adsorptivity and it can be increased by immobilizing hydrophobic
structure to attract organic compounds. In this work natural
montmorillonite were modified with cetyltrimethylammonium
(CTMA+) and was evaluated for use as adsorbents of aromatic
compounds: benzene, toluene, and 2-chloro phenol in its single and
multicomponent solution by ethanol:water solvent. Preparation of
CTMA-montmorillonite was conducted by simple ion exchange
procedure and characterization was conducted by using x-day
diffraction (XRD), Fourier-transform infra red (FTIR) and gas
sorption analysis. The influence of structural modification of
montmorillonite on its adsorption capacity and adsorption affinity of
organic compound were studied. It was shown that adsorptivity of
montmorillonite was increased by modification associated with
arrangements of CTMA+ in the structure even the specific surface
area of modified montmorillonite was lower than raw
montmorillonite. Adsorption rate indicated that material has affinity
to adsorb compound by following order: benzene> toluene > 2-chloro
phenol. The adsorption isotherms of benzene and toluene showed 1st
order adsorption kinetic indicating a partition phenomenon of
compounds between the aqueous and organophilic CTMAmontmorillonite.
Abstract: Lipases are enzymes particularly amenable for
immobilization by entrapment methods, as they can work equally
well in aqueous or non-conventional media and long-time stability of
enzyme activity and enantioselectivity is needed to elaborate more
efficient bioprocesses. The improvement of Pseudomonas
fluorescens (Amano AK) lipase characteristics was investigated by
optimizing the immobilization procedure in hybrid organic-inorganic
matrices using ionic liquids as additives. Ionic liquids containing a
more hydrophobic alkyl group in the cationic moiety are beneficial
for the activity of immobilized lipase. Silanes with alkyl- or aryl
nonhydrolizable groups used as precursors in combination with
tetramethoxysilane could generate composites with higher
enantioselectivity compared to the native enzyme in acylation
reactions of secondary alcohols. The optimal effect on both activity
and enantioselectivity was achieved for the composite made from
octyltrimethoxysilane and tetramethoxysilane at 1:1 molar ratio (60%
increase of total activity following immobilization and enantiomeric
ratio of 30). Ionic liquids also demonstrated valuable properties as
reaction media for the studied reactions, comparable with the usual
organic solvent, hexane.
Abstract: In this work study the location of interface in a stirred vessel with a Concave impeller by computational fluid dynamic was presented. To modeling rotating the impeller, sliding mesh (SM) technique was used and standard k-ε model was selected for turbulence closure. Mean tangential, radial and axial velocities and also turbulent kinetic energy (k) and turbulent dissipation rate (ε) in various points of tank was investigated. Results show sensitivity of system to location of interface and radius of 7 to 10cm for interface in the vessel with existence characteristics cause to increase the accuracy of simulation.
Abstract: A large quantity of world-s oil reserves exists in
carbonate reservoirs. Carbonate reservoirs are very sensitive to
chemical enhanced oil recovery process because of containing large
amount of calcite, dolomite and calcium sulfate minerals. These
minerals cause major obstacles during alkali-surfactant-polymer
(ASP) flooding. Alkali reacts with these minerals and form undesired
precipitations which plug effective porous openings, reduce
permeability and cause scale occurrence at the wellbore. In this
paper, a new chemical combination consists of acrylic acid and alkali
was used to minimize precipitation problem during ASP flooding. A
series of fluid-fluid compatibility tests were performed using acrylic
acid and different concentrations of alkaline. Two types of alkalis
namely; sodium carbonate and sodium metaborate were screened. As
a result, the combination of acrylic acid and sodium carbonate was
not effective in preventing calcium and magnesium precipitations.
However, acrylic acid and sodium metaborate showed promising
results for keeping all solutions without any precipitations. The ratio
of acrylic acid to sodium metaborate of 0.7:1.0 was found to be
optimum for achieving a compatible solution for 30 days at 80oC.
Abstract: The possibility of using cassava residue containing
49.66% starch, 21.47% cellulose, 12.97% hemicellulose, and 21.86%
lignin as a raw material to produce glucose using enzymatic
hydrolysis was investigated. In the experiment, each reactor
contained the cassava residue, bacteria cells, and production medium.
The effects of particles size (40 mesh and 60 mesh) and strains of
bacteria (A002 and M015) isolated from Thai higher termites,
Microcerotermes sp., on the glucose concentration at 37°C were
focused. High performance liquid chromatography (HPLC) with a
refractive index detector was used to determine the quantity of
glucose. The maximum glucose concentration obtained at 37°C using
strain A002 and 60 mesh of the cassava residue was 1.51 g/L at 10 h.
Abstract: An interesting method to produce calcium carbonate is based in a gas-liquid reaction between carbon dioxide and aqueous solutions of calcium hydroxide. The design parameters for gas-liquid phase are flow regime, individual mass transfer, gas-liquid specific interfacial area. Most studies on gas-liquid phase were devoted to the experimental determination of some of these parameters, and more specifically, of the mass transfer coefficient, kLa which depends fundamentally on the superficial gas velocity and on the physical properties of absorption phase. The principle investigation was directed to study the effect of the vibration on the mass transfer coefficient kLa in gas-liquid phase during absorption of CO2 in the in aqueous solution of calcium hydroxide. The vibration with a higher frequency increase the mass transfer coefficient kLa, but vibration with lower frequency didn-t improve it, the mass transfer coefficient kLa increase with increase the superficial gas velocity.
Abstract: Studies on Simultaneous Saccharification and Fermentation (SSF) of corn flour, a major agricultural product as the substrate using starch digesting glucoamylase enzyme derived from Aspergillus niger and non starch digesting and sugar fermenting Saccharomyces cerevisiae in a batch fermentation. Experiments based on Central Composite Design (CCD) were conducted to study the effect of substrate concentration, pH, temperature, enzyme concentration on Ethanol Concentration and the above parameters were optimized using Response Surface Methodology (RSM). The optimum values of substrate concentration, pH, temperature and enzyme concentration were found to be 160 g/l, 5.5, 30°C and 50 IU respectively. The effect of inoculums age on ethanol concentration was also investigated. The corn flour solution equivalent to 16% initial starch concentration gave the highest ethanol concentration of 63.04 g/l after 48 h of fermentation at optimum conditions of pH and temperature. Monod model and Logistic model were used for growth kinetics and Leudeking – Piret model was used for product formation kinetics.
Abstract: Polyurethane foam (PUF) were prepared by
reacting polyols synthesized from soy-oil into mixture of 2,4-
Toluene diisocyanate (TDI) with 4,4--Methylene Diamine
Isocyanate (MDI) with ratio of 70:30. The polyols obtained
via esterification reaction were categorize into different
temperature of reaction and by used of varied concentration
of phosphoric acid catalyst. The purpose of catalysts is to
shifting selectivity to a desired and value added of product.
The effect of stoichiometric balance (molar ratio of
epoxide/ethylene glycol) to the concentration of the catalyst
on the final properties was evaluated.
Abstract: Air pollution is a major environmental health
problem, affecting developed and developing countries around the
world. Increasing amounts of potentially harmful gases and
particulate matter are being emitted into the atmosphere on a global
scale, resulting in damage to human health and the environment.
Petroleum-related air pollutants can have a wide variety of adverse
environmental impacts. In the crude oil production sectors, there is a
strong need for a thorough knowledge of gaseous emissions resulting
from the flaring of associated gas of known composition on daily
basis through combustion activities under several operating
conditions. This can help in the control of gaseous emission from
flares and thus in the protection of their immediate and distant
surrounding against environmental degradation.
The impacts of methane and non-methane hydrocarbons emissions
from flaring activities at oil production facilities at Kuwait Oilfields
have been assessed through a screening study using records of flaring
operations taken at the gas and oil production sites, and by analyzing
available meteorological and air quality data measured at stations
located near anthropogenic sources. In the present study the
Industrial Source Complex (ISCST3) Dispersion Model is used to
calculate the ground level concentrations of methane and nonmethane
hydrocarbons emitted due to flaring in all over Kuwait
Oilfields.
The simulation of real hourly air quality in and around oil
production facilities in the State of Kuwait for the year 2006,
inserting the respective source emission data into the ISCST3
software indicates that the levels of non-methane hydrocarbons from
the flaring activities exceed the allowable ambient air standard set by
Kuwait EPA. So, there is a strong need to address this acute problem
to minimize the impact of methane and non-methane hydrocarbons
released from flaring activities over the urban area of Kuwait.
Abstract: The influence of viscosity on droplet diameter for
water-in-crude oil (w/o) emulsion with two different ratios; 20-80 %
and 50-50 % w/o emulsion was examined in the Brookfield
Rotational Digital Rheometer. The emulsion was prepared with
sorbitan sesquiolate (Span 83) act as emulsifier at varied temperature
and stirring speed in rotation per minute (rpm). Results showed that
the viscosity of w/o emulsion was strongly augmented by increasing
volume of water and decreased the temperature. The changing of
viscosity also altered the droplet size distribution. Changing of
droplet diameter was depends on the viscosity and the behavior of
emulsion either Newtonian or non-Newtonian.
Abstract: Performance of a cobalt doped sol-gel derived silica (Co/SiO2) catalyst for Fischer–Tropsch synthesis (FTS) in slurryphase reactor was studied using paraffin wax as initial liquid media. The reactive mixed gas, hydrogen (H2) and carbon monoxide (CO) in a molar ratio of 2:1, was flowed at 50 ml/min. Braunauer-Emmett- Teller (BET) surface area and X-ray diffraction (XRD) techniques were employed to characterize both the specific surface area and crystallinity of the catalyst, respectively. The reduction behavior of Co/SiO2 catalyst was investigated using the Temperature Programmmed Reduction (TPR) method. Operating temperatures were varied from 493 to 533K to find the optimum conditions to maximize liquid fuels production, gasoline and diesel.
Abstract: This study deals with evaluation of influence of salinity (NaCl) onto equilibrium of Cu and Ni removal from aqueous solutions by natural sorbent – zeolite. Equilibrium data were obtained by batch experiments. The salinity of the aqueous solution was influenced by dissolving NaCl in distilled water. It was studied in the range of NaCl concentrations from 1 g.l-1 to 100g.l-1. For Cu sorption there is a significant influence of salinity. The maximum capacity of zeolite for Cu was decreasing with growing concentration of NaCl. For Ni sorption there is not so significant influence of salinity as for Cu. The maximum capacity of zeolite for Ni was slightly decreasing with growing concentration of NaCl.
Abstract: Novel acrylated epoxidized hemp oil (AEHO) based
bioresins were successfully synthesised, characterized and applied to
biocomposites reinforced with woven jute fibre. Characterisation of
the synthesised AEHO consisted of acid number titrations and FTIR
spectroscopy to assess the success of the acrylation reaction. Three
different matrices were produced (vinylester (VE), 50/50 blend of
AEHO/VE and 100% AEHO) and reinforced with jute fibre to form
three different types of biocomposite samples. Mechanical properties
in the form of flexural and interlaminar shear strength (ILSS) were
investigated and compared for the different samples. Results from the
mechanical tests showed that AEHO and 50/50 based neat bioresins
displayed lower flexural properties compared with the VE samples.
However when applied to biocomposites and compared with VE
based samples, AEHO biocomposites demonstrated comparable
flexural performance and improved ILSS. These results are attributed
to improved fibre-matrix interfacial adhesion due to surface-chemical
compatibility between the natural fibres and bioresin.
Abstract: This paper presents the comparison ageing deterioration of silicone rubber housing material for outdoor polymer insulators by using salt fog ageing test based on IEC 61109 and outdoor exposure test.Four types of high temperature silicone vulcanized silicone rubber sheet with different amount of ATH were used as testing specimen. For salt fog ageing test, the specimens were tested continuously 1000 hours with energized in test chamber. For outdoor exposure test, the specimens were hung continuously 18 months without energized. Physical and chemical analyses were conducted to evaluate degree of ageing deterioration of tested specimens. Slightly surface erosion was observed on specimen surface after salt fog ageing test and no erosion was observed on surface of outdoor exposure specimen. However, comparable degree of ageing deterioration can be seen from surface analysis results.
Abstract: The aim of our work is to study phase composition,
particle size and magnetic response of Fe2O3/TiO2 nanocomposites
with respect to the final annealing temperature. Those nanomaterials
are considered as smart catalysts, separable from a liquid/gaseous
phase by applied magnetic field. The starting product was obtained
by an ecologically acceptable route, based on heterogeneous
precipitation of the TiO2 on modified g-Fe2O3 nanocrystals dispersed
in water. The precursor was subsequently annealed on air at
temperatures ranging from 200 oC to 900 oC. The samples were
investigated by synchrotron X-ray powder diffraction (S-PXRD),
magnetic measurements and Mössbauer spectroscopy. As evidenced
by S-PXRD and Mössbauer spectroscopy, increasing the annealing
temperature causes evolution of the phase composition from
anatase/maghemite to rutile/hematite, finally above 700 oC the
pseudobrookite (Fe2TiO5) also forms. The apparent particle size of
the various Fe2O3/TiO2 phases has been determined from the highquality
S-PXRD data by using two different approaches: the Rietveld
refinement and the Debye method. Magnetic response of the samples
is discussed in considering the phase composition and the particle
size.
Abstract: Since injection engines have a considerable portion, in
consumption of energy and environmental pollution, using an
alternative source of energy with lower pollutant effects in this
regard is necessary.
Biodiesel fuel is a suitable alternative for gasoline in diesel
engines.
In this research the property of biodiesel, the function and the
pollution effects of diesel engine, when using 100% biodiesel, using
100% gasoline and mixing ratio of both fuels for comparing them,
have been investigated.
The researches have shown, using biodiesel fuel in prevalent
diesel engine, will reduce the pollutants such as Co, half burned
carbohydrate and suspended particles and a little increase in
oxidation will achieve while power consumption, particularly fuel
and thermal efficiency of diesel fuel has the same.
Abstract: Group-III nitride material as particularly AlxGa1-xN is
one of promising optoelectronic materials to require for shortwavelength
devices. To achieve the high-quality AlxGa1-xN films for
a high performance of such devices, AlN-nucleation layers are the
important factor. To improve the AlN-nucleation layers with a
variation of Ga-addition, XRD measurements were conducted to
analyze the crystalline quality of the subsequent Al0.1Ga0.9N with the
minimum ω-FWHMs of (0002) and (10-10) reflections of 425 arcsec
and 750 arcsec, respectively. SEM and AFM measurements were
performed to observe the surface morphology and TEM
measurements to identify the microstructures and orientations.
Results showed that the optimized Ga-atoms in the Al(Ga)Nnucleation
layers improved the surface diffusion to form moreuniform
crystallites in structure and size, better alignment of each
crystallite, and better homogeneity of island distribution. This, hence,
improves the orientation of epilayers on the Si-surface and finally
improves the crystalline quality and reduces the residual strain of
subsequent Al0.1Ga0.9N layers.
Abstract: Pharmaceutical industries and effluents of sewage treatment plants are the main sources of residual pharmaceuticals in water resources. These emergent pollutants may adversely impact the biophysical environment. Pharmaceutical industries often generate wastewater that changes in characteristics and quantity depending on the used manufacturing processes. Carbamazepine (CBZ), {5Hdibenzo [b,f]azepine-5-carboxamide, (C15H12N2O)}, is a significant non-biodegradable pharmaceutical contaminant in the Jordanian pharmaceutical wastewater, which is not removed by the activated sludge processes in treatment plants. Activated carbon may potentially remove that pollutant from effluents, but the high cost involved suggests that more attention should be given to the potential use of low-cost materials in order to reduce cost and environmental contamination. Powders of Jordanian non-metallic raw materials namely, Azraq Bentonite (AB), Kaolinite (K), and Zeolite (Zeo) were activated (acid and thermal treatment) and evaluated by removing CBZ. The results of batch and column techniques experiments showed around 46% and 67% removal of CBZ respectively.