Abstract: This paper study the segmented split capacitor
Digital-to-Analog Converter (DAC) implemented in a differentialtype
12-bit Successive Approximation Analog-to-Digital Converter
(SA-ADC). The series capacitance split array method employed as it
reduced the total area of the capacitors required for high resolution
DACs. A 12-bit regular binary array structure requires 2049 unit
capacitors (Cs) while the split array needs 127 unit Cs. These results
in the reduction of the total capacitance and power consumption of
the series split array architectures as to regular binary-weighted
structures. The paper will show the 12-bit DAC series split capacitor
with 4-bit thermometer coded DAC architectures as well as the
simulation and measured results.
Abstract: This paper presents a method to estimate load profile
in a multiple power flow solutions for every minutes in 24 hours per
day. A method to calculate multiple solutions of non linear profile is
introduced. The Power System Simulation/Engineering (PSS®E) and
python has been used to solve the load power flow. The result of this
power flow solutions has been used to estimate the load profiles for
each load at buses using Independent Component Analysis (ICA)
without any knowledge of parameter and network topology of the
systems. The proposed algorithm is tested with IEEE 69 test bus
system represents for distribution part and the method of ICA has
been programmed in MATLAB R2012b version. Simulation results
and errors of estimations are discussed in this paper.
Abstract: Space Vector Pulse Width Modulation SVPWM is
one of the most used techniques to generate sinusoidal voltage and
current due to its facility and efficiency with low harmonics
distortion. This algorithm is specially used in power electronic
applications. This paper describes simulation algorithm of SVPWM
& SPWM using MatLab/simulink environment. It also implements a
closed loop three phases DC-AC converter controlling its outputs
voltages amplitude and frequency using MatLab. Also comparison
between SVPWM & SPWM results is given.
Abstract: In this paper, we propose a novel limited feedback scheme for task planning with service robots. Instead of sending the full service robot state information for the task planning, the proposed scheme send the best-M indices of service robots with a indicator. With the indicator, the proposed scheme significantly reduces the communication overhead for task planning as well as mitigates the system performance degradation in terms of the utility. In addition, we analyze the system performance of the proposed scheme and compare the proposed scheme with the other schemes.
Abstract: We proposes a way of removing noises and reducing the number of colors contained in a JPEG image. Main purpose of this project is to convert color images to monochrome images for the color blinds. We treat the crispy color images like the Tokyo subway map. Each color in the image has an important information. But for the color blinds, similar colors cannot be distinguished. If we can convert those colors to different gray values, they can distinguish them.
Abstract: The advancement of smartphones, wireless
networking and Near Field Communication (NFC) technology have
opened up a new approach to indoor navigation. Although NFC
technology has been used to support electronic commerce, access
control, and ticketing, there is a lack of research work on building
NFC-based indoor navigation system for smartphone users. This
paper presents an indoor interactive navigation system (named
I2Navi) based on NFC technology for users to navigate within a
building with ease using their smartphones. The I2Navi system has
been implemented at the Faculty of Engineering (FOE), Multimedia
University (MMU) to enable students, parents, visitors who own
NFC-enabled Android smartphones to navigate themselves within the
faculty. An evaluation is carried out and the results show positive
response to the proposed indoor navigation system using NFC and
smartphone technologies.
Abstract: Fluorescent and WOLED are widely used because it consumes less energy. However, both lamps cause a harmonics because it has semiconductors components. Harmonic is a distorted sinusoidal electric wave and cause excess heat. This study compares the amount of harmonics generated by both lamps. The test shows that both lamps have THDv(Total Harmonics Distortion of Voltage) almost the same with average 2.5% while the average of WOLED's THDi(Total Harmonics Distortion of Current) is lower than fluorescent has. The average WOLED's THDi is 29.10 % and fluorescent's 'THDi is 87. 23 %.
Abstract: The demand on High voltage (HV) infrastructures is growing due to the corresponding growth in industries and population. Many areas are being developed and therefore require additional electrical power to comply with the demand. Substation upgrade is one of the rapid solutions to ensure the continuous supply of power to customers. This upgrade requires civil modifications to structures and fences. The civil work requires excavation and steel works that may create unsafe touch conditions. This paper presents a brief theoretical overview of the touch voltage inside and around substations and uses CDEGS software to simulate a case study.
Abstract: In this paper a three dimensional thermal model of
high breaking capacity fuse with unequal fuse links is proposed for
both steady-state or transient conditions. The influence of ambient
temperature and electric current on the temperature distribution
inside the fuse, has been investigated. A thermal analysis of the
unbalanced distribution of the electric current through the fuse
elements and their influence on fuse link temperature rise, has been
performed. To validate the three dimensional thermal model, some
experimental tests have been done. There is a good correlation
between experimental and simulation results.
Abstract: This paper presented a proposed design for
transcutaneous inductive powering links. The design used to transfer
power and data to the implanted devices such as implanted
Microsystems to stimulate and monitoring the nerves and muscles.
The system operated with low band frequency 13.56 MHZ according
to industrial- scientific – medical (ISM) band to avoid the tissue
heating. For external part, the modulation index is 13 % and the
modulation rate 7.3% with data rate 1 Mbit/s assuming Tbit=1us. The
system has been designed using 0.35-μm fabricated CMOS
technology. The mathematical model is given and the design is
simulated using OrCAD P Spice 16.2 software tool and for real-time
simulation the electronic workbench MULISIM 11 has been used.
The novel circular plane (pancake) coils was simulated using
ANSOFT- HFss software.
Abstract: Memristor is also known as the fourth fundamental
passive circuit element. When current flows in one direction through
the device, the electrical resistance increases and when current flows
in the opposite direction, the resistance decreases. When the current
is stopped, the component retains the last resistance that it had, and
when the flow of charge starts again, the resistance of the circuit will
be what it was when it was last active. It behaves as a nonlinear
resistor with memory. Recently memristors have generated wide
research interest and have found many applications. In this paper we
survey the various applications of memristors which include non
volatile memory, nanoelectronic memories, computer logic,
neuromorphic computer architectures low power remote sensing
applications, crossbar latches as transistor replacements, analog
computations and switches.
Abstract: A power measurement algorithm of the input mix components of the noise signal and narrowband interference is considered using functional transformations of the input mix in the postdetection processing channel. The algorithm efficiency analysis has been carried out for different interference-to-signal ratio. Algorithm performance features have been explored by numerical experiment results.
Abstract: The prologue of new High Voltage (HV) transmission
mains into the community necessitates earthing design to ensure
safety compliance of the system. Conductive structures such as steel
or concrete poles are widely used in HV transmission mains. The
earth potential rise (EPR) generated by a fault on these structures
could result to an unsafe condition. This paper discusses information
on the input impedance of the over head earth wire (OHEW) system
for finite and infinite transmission mains. The definition of finite and
infinite system is discussed, maximum EPR due to pole fault. The
simplified equations for EPR assessments are introduced and
discussed for the finite and infinite conditions. A case study is also
shown.
Abstract: In this paper, the application of GRNN in
modeling of SOFC fuel cells were studied. The parameters
are of interested as voltage and power value and the current
changes are investigated. In addition, the comparison between
GRNN neural network application and conventional method
was made. The error value showed the superlative results.