Abstract: The present paper is a case study about exploitation of
Kheir Abad river (Khoozestan, Iran) water resources and the
problems caused by river sediments around the pumping stations.
The weak points and strong points of Boneh Basht pumping station
have been studied by experienced experts, work teams, and
consulting engineers and technical and executive solutions have been
suggested. Therefore, the suggestions of this article are based on the
performed studies and are proposed in order to evaluate the logical
solutions.
Rather complicated processes resulting from the interaction of
water flows and sediments observed at Boneh Basht pumping station
occur at other pumping stations in almost the same way. Therefore,
Boneh Basht pumping station can be selected as a sample (pilot) and
up-to-date theories and experiences can be applied to this station and
the results can be offered to other stations.
Abstract: Reducing river sediments through path correction and
preservation of river walls leads to considerable reduction of
sedimentation at the pumping stations. Path correction and
preservation of walls is not limited to one particular method but,
depending on various conditions, a combination of several methods
can be employed. In this article, we try to review and evaluate
methods for preservation of river banks in order to reduce sediments.
Abstract: Shirvan is located in plain in Northern Khorasan province north east of Iran and has semiarid to temperate climate. To investigate the annual changes in some qualitative parameters such as electrical conductivity, total dissolved solids and chloride concentrations which have increased during ten continuous years. Fourteen groundwater sources including deep as well as semi-deep wells were sampled and were analyzed using standard methods. The trends of obtained data were analyzed during these years and the effects of different factors on the changes in electrical conductivity, concentration of chloride and total dissolved solids were clarified. The results showed that the amounts of some qualitative parameters have been increased during 10 years time which has led to decrease in water quality. The results also showed that increased in urban populations as well as extensive industrialization in the studied area are the most important reasons to influence underground water quality. Furthermore decrease in water quantity is also evident due to more water utilization and occurrence of recent droughts in the region during recent years.
Abstract: One of the main issues in Computer Vision is to extract the movement of one or several points or objects of interest in an image or video sequence to conduct any kind of study or control process. Different techniques to solve this problem have been applied in numerous areas such as surveillance systems, analysis of traffic, motion capture, image compression, navigation systems and others, where the specific characteristics of each scenario determine the approximation to the problem. This paper puts forward a Computer Vision based algorithm to analyze fish trajectories in high turbulence conditions in artificial structures called vertical slot fishways, designed to allow the upstream migration of fish through obstructions in rivers. The suggested algorithm calculates the position of the fish at every instant starting from images recorded with a camera and using neural networks to execute fish detection on images. Different laboratory tests have been carried out in a full scale fishway model and with living fishes, allowing the reconstruction of the fish trajectory and the measurement of velocities and accelerations of the fish. These data can provide useful information to design more effective vertical slot fishways.
Abstract: In this paper, the significant wave height at the Upper Gulf of Thailand and the changing of wave height at Bangkhuntien shoreline were simulated by using the Simulating WAves Nearshore Model (SWAN) version 40.51. The simulated results indicated that the significant wave height by SWAN model corresponded with the observed data. The results showed that the maximum significant wave height at the Bangkhuntien shoreline were 1.06-2.05 m. and the average significant wave height at the Bangkhuntien shoreline were 0.30-0.47 m. The significant wave height can be used to calculate the erosion through the Bangkhuntien shoreline. The erosion rates at the Bangkhuntien shoreline were prepared by using the aerial photo and they were about 1.80 m/yr. from 1980- 1986, 4.75 m/yr from 1987-1993, 15.28 m/yr from 1994-1996 and 10.03 m/yr from 1997-2002. The relation between the wave energy and the erosion were in good agreement. Therefore, the significant wave height was one of the major factors of the erosion at the Bangkhuntien shoreline.
Abstract: Presently and in line with the United Nations (EPA),
human thinking system has shifted towards clean fuels so as to
maintain a cleaner environment and to save our planet earth.
One of the most successful studies in order to achieve new
energies includes the use of animal wastes and their organic residues,
and the result of these researches has been represented in the form of
very simple and cheap methods called biogas technology. Biogas
technology has developed a lot in the recent decades; its reason is the
high cost of fossil fuels and the greater attention of countries to the
environmental pollutions due to the consumption of this kind of
fuels.
IRAN is ready for the optimized application of renewable
energies, having much enriched resources of this kind of energies; so
a special place could be considered for it when making programs.
The purpose of biogas technology is the recovery of energy and
finally the protection of the environment, which is much appropriate
for the third world farmers with respect to their technical abilities and
economic potentials. Studies show that the production and
consumption of biogas is appropriate and economic in IRAN,
because of the high amount of waste in the agriculture sector, the
significant amount of animal and human excrement production, the
great volume of garbage produced and the most important the
specific social, climatic and agricultural conditions in IRAN, in order
to proceed towards the reduction of pollution due to the use of fossil
fuels.
Abstract: In this study, the Scots pine (Pinus sylvestris L.) C
needles (i.e. the current-year-needles) were used as bioindicators in
determining the aerial distribution pattern of sulphur emissions
around industrial point sources at Kemi, Northern Finland. The
average sulphur concentration in the C needles was 897 mg/kg
(d.w.), with a standard deviation of 118 mg/kg (d.w.) and range 740 –
1350 mg/kg (d.w.). According to results in this study, Scots pine
needles (Pinus sylvestris L.) appear to be an ideal bioindicators for
identifying atmospheric sulphur pollution derived from industrial
plants and can complement the information provided by plant
mapping studies around industrial plants.
Abstract: It has formed an essential issue that Climate Change, composed of highly knowledge complexity, reveals its significant impact on human existence. Therefore, specific national policies, some of which present the educational aspects, have been published for overcoming the imperative problem. Accordingly, the study aims to analyze as well as integrate the relationship between Climate Change and environmental education and apply the perspective of concept map to represent the knowledge contents and structures of Climate Change; by doing so, knowledge contents of Climate Change could be represented in an even more comprehensive way and manipulated as the tool for environmental education. The method adapted for this study is knowledge conversion model compounded of the platform for experts and teachers, who were the participants for this study, to cooperate and combine each participant-s standpoints into a complete knowledge framework that is the foundation for structuring the concept map. The result of this research contains the important concepts, the precise propositions and the entire concept map for representing the robust concepts of Climate Change.
Abstract: A numerical analysis of wave and hydrodynamic models
is used to investigate the influence of WAve and Storm Surge
(WASS) in the regional and coastal zones. The numerical analyzed
system consists of the WAve Model Cycle 4 (WAMC4) and the
Princeton Ocean Model (POM) which used to solve the energy
balance and primitive equations respectively. The results of both
models presented the incorporated surface wave in the regional
zone affected the coastal storm surge zone. Specifically, the results
indicated that the WASS generally under the approximation is not
only the peak surge but also the coastal water level drop which
can also cause substantial impact on the coastal environment. The
wave–induced surface stress affected the storm surge can significantly
improve storm surge prediction. Finally, the calibration of wave
module according to the minimum error of the significant wave height
(Hs) is not necessarily result in the optimum wave module in the
WASS analyzed system for the WASS prediction.
Abstract: Permanent rivers are the main sources of renewable
water supply for the croplands under the irrigation and drainage
schemes. They are also the major source of sediment loads transport
into the storage reservoirs of the hydro-electrical dams, diversion
weirs and regulating dams. Sedimentation process results from soil
erosion which is related to poor watershed management and human
intervention ion in the hydraulic regime of the rivers. These could
change the hydraulic behavior and as such, leads to riverbed and river
bank scouring, the consequences of which would be sediment load
transport into the dams and therefore reducing the flow discharge in
water intakes. The present paper investigate sedimentation process
by varying the Manning coefficient "n" by using the SHARC
software along the watercourse in the Dez River. Results indicated
that the optimum "n" within that river range is 0.0315 at which
quantity minimum sediment loads are transported into the Eastern
intake. Comparison of the model results with those obtained by those
from the SSIIM software within the same river reach showed a very
close proximity between them. This suggests a relative accuracy with
which the model can simulate the hydraulic flow characteristics and
therefore its suitability as a powerful analytical tool for project
feasibility studies and project implementation.
Abstract: The hydro-mechanical model for unsaturated soils has
been presented based on the effective stress principle taking into
account effects of drying-wetting process. The elasto-plastic
constitutive equations for stress-strain relations of the soil skeleton
have been established. A plasticity model is modified from modified
Cam-Clay model. The hardening rule has been established by
considering the isotropic consolidation paths. The effect of dryingwetting
process is introduced through the ¤ç parameter. All model
coefficients are identified in terms of measurable parameters. The
simulations from the proposed model are compared with the
experimental results. The model calibration was performed to extract
the model parameter from the experimental results. Good agreement
between the results predicted using proposed model and the
experimental results was obtained.
Abstract: Some methodologies were compared in providing
erosion maps of surface, rill and gully and erosion features, in
research which took place in the Varamin sub-basin, north-east
Tehran, Iran. A photomorphic unit map was produced from
processed satellite images, and four other maps were prepared by the
integration of different data layers, including slope, plant cover,
geology, land use, rocks erodibility and land units. Comparison of
ground truth maps of erosion types and working unit maps indicated
that the integration of land use, land units and rocks erodibility layers
with satellite image photomorphic units maps provide the best
methods in producing erosion types maps.
Abstract: Sedimentation is a hydraulic phenomenon that is
emerging as a serious challenge in river engineering. When the flow
reaches a certain state that gather potential energy, it shifts the
sediment load along channel bed. The transport of such materials can
be in the form of suspended and bed loads. The movement of these
along the river course and channels and the ways in which this could
influence the water intakes is considered as the major challenges for
sustainable O&M of hydraulic structures. This could be very serious
in arid and semi-arid regions like Iran, where inappropriate watershed
management could lead to shifting a great deal of sediments into the
reservoirs and irrigation systems. This paper aims to investigate
sedimentation in the Western Canal of Dez Diversion Weir in Iran,
identifying factors which influence the process and provide ways in
which to mitigate its detrimental effects by using the SHARC
Software.
For the purpose of this paper, data from the Dezful water authority
and Dezful Hydrometric Station pertinent to a river course of about 6
Km were used.
Results estimated sand and silt bed loads concentrations to be 193
ppm and 827ppm respectively. Given the available data on average
annual bed loads and average suspended sediment loads of 165ppm
and 837ppm, there was a significant statistical difference (16%)
between the sand grains, whereas no significant difference (1.2%)
was find in the silt grain sizes. One explanation for such finding
being that along the 6 Km river course there was considerable
meandering effects which explains recent shift in the hydraulic
behavior along the stream course under investigation. The sand
concentration in downstream relative to present state of the canal
showed a steep descending curve. Sediment trapping on the other
hand indicated a steep ascending curve. These occurred because the
diversion weir was not considered in the simulation model.
Abstract: Having a very many number of pipelines all over the
country, Iran is one of the countries consists of various ecosystems
with variable degrees of fragility and robusticity as well as
geographical conditions. This study presents a state-of-the-art method
to estimate environmental risks of pipelines by recommending
rational equations including FES, URAS, SRS, RRS, DRS, LURS
and IRS as well as FRS to calculate the risks. This study was carried
out by a relative semi-quantitative approach based on land uses and
HVAs (High-Value Areas). GIS as a tool was used to create proper
maps regarding the environmental risks, land uses and distances. The
main logic for using the formulas was the distance-based approaches
and ESI as well as intersections. Summarizing the results of the
study, a risk geographical map based on the ESIs and final risk score
(FRS) was created. The study results showed that the most sensitive
and so of high risk area would be an area comprising of mangrove
forests located in the pipeline neighborhood. Also, salty lands were
the most robust land use units in the case of pipeline failure
circumstances. Besides, using a state-of-the-art method, it showed
that mapping the risks of pipelines out with the applied method is of
more reliability and convenience as well as relative
comprehensiveness in comparison to present non-holistic methods for
assessing the environmental risks of pipelines. The focus of the
present study is “assessment" than that of “management". It is
suggested that new policies are to be implemented to reduce the
negative effects of the pipeline that has not yet been constructed
completely
Abstract: Establishing pumping stations is one of the most common ways of providing water from rivers. There are many issues involved in the design and operation of pumping stations most important of which is the problem of sedimentation. One of the significant issues which must be taken into consideration in designing pumping stations is the operation method and technical matters related to it. Safety and convenience of operation is one of the issues that must be always considered by the designer. Some of the major issues in making decisions regarding the type of design for the station are geographical condition, the location of the station and availability of experts in maintenance and operation of the station. Dimensions of the station must allow free movement for checking and operating pumps after installation of pumps and plumbing system.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: This paper introduces the application of seismic wave method in earthquake prediction and early estimation. The advantages of the seismic wave method over the traditional earthquake prediction method are demonstrated. An example is presented in this study to show the accuracy and efficiency of using the seismic wave method in predicting a medium-sized earthquake swarm occurred in Wencheng, Zhejiang, China. By applying this method, correct predictions were made on the day after this earthquake swarm started and the day the maximum earthquake occurred, which provided scientific bases for governmental decision-making.
Abstract: Analytical investigation of the sedimentation
processes in the river engineering and hydraulic structures is of vital
importance as this can affect water supply for the cultivating lands in
the command area. The reason being that gradual sediment formation
behind the reservoir can reduce the nominal capacity of these dams.
The aim of the present paper is to analytically investigate
sedimentation process along the river course and behind the storage
reservoirs in general and the Eastern Intake of the Dez Diversion weir
in particular using the SHARC software. Results of the model
indicated the water level at 115.97m whereas the real time
measurement from the river cross section was 115.98 m which
suggests a significantly close relation between them. The average
transported sediment load in the river was measured at 0.25mm ,
from which it can be concluded that nearly 100% of the suspended
loads in river are moving which suggests no sediment settling but
indicates that almost all sediment loads enters into the intake. It was
further showed the average sediment diameter entering the intake to
be 0.293 mm which in turn suggests that about 85% of suspended
sediments in the river entre the intake. Comparison of the results
from the SHARC model with those obtained form the SSIIM
software suggests quite similar outputs but distinguishing the
SHARC model as more appropriate for the analysis of simpler
problems than other model.