Tribological Behaviour Improvement of Lubricant Using Copper (II) Oxide Nanoparticles as Additive

Tribological properties that include nanoparticles are an alternative to improve the tribological behaviour of lubricating oil, which has been investigated by many researchers for the past few decades. Various nanostructures can be used as additives for tribological improvement. However, this also depends on the characteristics of the nanoparticles. In this study, tribological investigation was performed to examine the effect of CuO nanoparticles on the tribological behaviour of Syntium 800 SL 10W−30. Three parameters used in the analysis using the wear tester (piston ring) were load, revolutions per minute (rpm), and concentration. The specifications of the nanoparticles, such as size, concentration, hardness, and shape, can affect the tribological behaviour of the lubricant. The friction and wear experiment was conducted using a tribo-tester and the Response Surface Methodology method was used to analyse any improvement of the performance. Therefore, two concentrations of 40 nm nanoparticles were used to conduct the experiments, namely, 0.005 wt % and 0.01 wt % and compared with base oil 0 wt % (control). A water bath sonicator was used to disperse the nanoparticles in base oil, while a tribo-tester was used to measure the coefficient of friction and wear rate. In addition, the thermal properties of the nanolubricant were also measured. The results have shown that the thermal conductivity of the nanolubricant was increased when compared with the base oil. Therefore, the results indicated that CuO nanoparticles had improved the tribological behaviour as well as the thermal properties of the nanolubricant oil.





References:
[1] Jatti, V.S. and T.P.Singh, Copper oxide nano-particles as friction-reduction and anti-wear additive in lubricating oil. Mechanical Science and Technology, 2015. 2: p. 793-798.
[2] Ettefaghi, E.-O.-I., et al., Preparation and thermal properties of oil-based nanofluid from mult-walled carbon nanotubes and engine oil as nano-lubricant. 2013: p. 142-147.
[3] Lee, K., et al., Understanding the role of nanoparticles in nano-oil lubrication. Tribol Lett, 2009: p. 127-131.
[4] Padgurskas, J., et al., Tribological properties of lubricant additive of Fe,Cu and Co nanoparticle. 2013: p. 224-232.
[5] Y.Y.Wu, W.C. Tsui, and T.C. Liu, Experimental analysis of tribological properties of lubricating oils with nanoparticles additive. Wear, 2007: p. 819-825.
[6] Koshy, C.P., P.K. Rejendrakumar, and M.V. Thottackad, Evalution of the tribological and thermo-physical properties of coconut oil added with MoS2 nanoparticle at elevated temperatures. Wear, 2015: p. 288-308.
[7] Battez, A.H., et al., CuO, ZrO2 and ZnO nanoparticles as antiwear additive in oil lubricants. Wear, 2008: p. 422-428.
[8] Abdullah, M.I.H.C., et al., Effect of hBN /Al2O3 nanoparticle on the tribological performance of engine oil 2014: p. 1-6.
[9] Zulkifli, N.W.M., et al., Experimental analysis of tribological properties of chemically modified bio-based lubricant with nanoparticle additives. 2013.
[10] Kapsiz, M., M. Durat, and F. Ficici, Friction and wear studies between cylinder liner and piston ring pair using Taguchi Method design method. Advance in Engineering Software, 2011: p. 595-603.
[11] Y.Choi, et al., Tribological behaviour of copper nanoparticles as additive in oil. Current applied physics, 2009: p. 124-127.
[12] Syaima, M.T.S., et al., Development of bio-lubricant from Jatropha curcas oils. 2014. 1(1).
[13] Idris, C., et al., The effect of diffeerent fuels on wear between piston ring and cylinder. 2014: p. 8.
[14] Ettefaghi, E.-o.-l., et al., Experimental evaluation of engine oil properties containing copper oxide nanoparticles as a nanoadditive. International Journal of Industrial Chemistry, 2013: p. 1-6.
[15] Alpaslan Atmanlı, et al., Response surface methodology based optimization of diesel–n-butanol –cotton oil ternary blend ratios to improve engine performance and exhaust emission characteristics. Energy Conversion and Management, 2015. 90(0): p. 383-394.
[16] Chang, B.P., et al., Optimization on wear performance of UHMWPE composites using response surface methodology. Tribology International, 2015: p. 252-262.
[17] Agarwal, G., A. Patnaik, and R.K. Sharma, Parametric optimization and three-body abrasive wear behavior of Sic filled chopped glass fiber reinforced epoxy composites. international journal of composite material, 2013. 2: p. 32-38.
[18] Srivastava, S.P., Advances in lubricant additive and tribological. 2009, Tribology society of India: New Delhi.