Thermal Analysis of Extrusion Process in Plastic Making

Plastic extrusion has been an important process of plastic production since 19^th century. Meanwhile, in plastic extrusion process, wide variation in temperature along the extrudate usually leads to scraps formation on the side of finished products. To avoid this situation, there is a need to deeply understand temperature distribution along the extrudate in plastic extrusion process. This work developed an analytical model that predicts the temperature distribution over the billet (the polymers melt) along the extrudate during extrusion process with the limitation that the polymer in question does not cover biopolymer such as DNA. The model was solved and simulated. Results for two different plastic materials (polyvinylchloride and polycarbonate) using self-developed MATLAB code and a commercially developed software (ANSYS) were generated and ultimately compared. It was observed that there is a thermodynamic heat transfer from the entry level of the billet into the die down to the end of it. The graph plots indicate a natural exponential decay of temperature with time and along the die length, with the temperature being 413 K and 474 K for polyvinylchloride and polycarbonate respectively at the entry level and 299.3 K and 328.8 K at the exit when the temperature of the surrounding was 298 K. The extrusion model was validated by comparison of MATLAB code simulation with a commercially available ANSYS simulation and the results favourably agree. This work concludes that the developed mathematical model and the self-generated MATLAB code are reliable tools in predicting temperature distribution along the extrudate in plastic extrusion process.

• S. K. Fasogbon
• T. M. Oladosu
• O. S. Osasuyi

• ANSYS
• extrusion process
• MATLAB
• plastic making
• thermal analysis.

[1] Asiedu Y. and Gu P., “Product life cycle cost analysis: state of the art review,” International Journal of Production Research, Volume 36, No 4, 1998, pp 883-908.
[2] Basily B. B. and Sansome D. H., “Some theoretical considerations for the direct drawing of section rod from round bar,” International Journal of Mechanical Sciences, vol. 18, no. 4, 1976, pp. 201-208.
[3] Brian R. T. and Wen J. T., “Extrusion Process Control: Modeling, Identification, and Optimization,” Control Systems Technology, IEEE Transactions on , Volume 6, 1998, Issue 2, pp 134-145 .
[4] Gatto, F. amp and Giarda A., “The characteristics of the three-dimensional analysis of plastic deformation according to the SERR method,” International Journal of Mechanical Sciences, vol. 23, no. 3, 1981, pp. 129-148.
[5] Jeffery A., “Advanced engineering mathematics,” Published by Academic press Inc., 2001, Pp 1114-1117.
[6] Kar P. K. and Das N. S., “Upper bound analysis of extrusion of I section bars from square/rectangular billets through square dies,” International Journal of Mechanical Sciences, vol. 39, no. 8, 1997, pp. 925- 934.
[7] Karania R. and Kazmer D., “Low volume plastics manufacturing strategies,” Journal of Mechanical Design, Vol. 129, 2007.
[8] Lewis R. W., Nithiarasu P. and Seetharamu, K. N., “Fundamentals of the Finite Element Method for Heat and Fluid Flow,” 1st ed. John Wiley and Sons, New York, 2004.
[9] Martin M. V. and Ishii K., “Design for variety: developing standardized and modularized product platform architectures,” Res. Eng. Des, Vol. 13, Issue 4, 2002, pp 213-235.
[10] Nagpal, V. and Altan, T., “Analysis of the three-dimensional metal flow in extrusion of shapes with the use of dual stream functions,” Proc. Third N.Am. Met. Res. Conf., Pittsburgh, Pennsylvenia, 1975, pp 26-40.
[11] Pathak K. K., Lomash S., Jain N. and Jha A. K., “Tube extrusion design for some selected inner profiles,” International Journal of Physical Sciences Vol. 4, Issue 2, 2009, pp. 69-75.
[12] Sahoo S. K. and Kar P. K., “Round-to-Square Extrusion Through Taper Die: A Three-dimensional Analysis,” Manufacturing Technology Proc. of 19th AIMDT Conf., 2000.