Design of Reconfigurable Supernumerary Robotic Limb Based on Differential Actuated Joints

This paper presents a wearable reconfigurable supernumerary robotic limb with differential actuated joints, which is lightweight, compact and comfortable for the wearers. Compared to the existing supernumerary robotic limbs which mostly adopted series structure with large movement space but poor carrying capacity, a prototype with the series-parallel configuration to better adapt to different task requirements has been developed in this design. To achieve a compact structure, two kinds of cable-driven mechanical structures based on guide pulleys and differential actuated joints were designed. Moreover, two different tension devices were also designed to ensure the reliability and accuracy of the cable-driven transmission. The proposed device also employed self-designed bearings which greatly simplified the structure and reduced the cost.





References:
[1] R. Gopura, D. S. V. Bandara, K. Kiguchi, “Developments in hardware systems of active upper-limb exoskeleton robots: A review,” Robotics and Autonomous Systems, Vol. 75, pp. 203–220, 2016.
[2] B. Llorens-Bonilla, F. Parietti, H. H. Asada, “Demonstration-based control of supernumerary robotic limbs,” Intelligent Robots and Systems (IROS), pp. 7–12, 2012.
[3] C. Davenpor, F. Parietti, H. H. Asada, “Design and biomechanical analysis of supernumerary robotic limbs” 5th annual dynamic systems and control conference joint with the 11th motion and vibration conference, pp. 787–793, 2012.
[4] F. Parietti, H. H. Asada, “Supernumerary robotic limbs for aircraft fuselage assembly: body stabilization and guidance by bracing” IEEE International Conference on Robotics and Automation (ICRA), pp. 1176-1183, 2014.
[5] D. Prattichizzo, M. Malvezzi, I. Hussain, “The sixth-finger: a modular extra-finger to enhance human hand capabilities” The 23rd IEEE International Symposium on Robot and Human Interactive Communication, pp. 993-998, 2014.
[6] F. Y. Wu, H. H. Asada, “Decoupled motion control of wearable robot for rejecting human induced disturbances” IEEE International Conference on Robotics and Automation (ICRA), pp. 1-8, 2018.
[7] F. Y. Wu, H. H. Asada, ““Hold-and-manipulate” with a single hand being assisted by wearable extra fingers” IEEE International Conference on Robotics and Automation (ICRA), pp. 6205-6212, 2015.
[8] F. Y. Wu, H. H. Asada, “Implicit and intuitive grasp posture control for wearable robotic fingers: A data-driven method using partial least squares”. IEEE Transactions on Robotics, Vol. 32, pp. 176–186, 2016.
[9] Y. Hu, S. Leigh, P. Maes, “Hand development kit: Soft robotic fingers as prosthetic augmentation of the hand” Adjunct Publication of the 30th Annual ACM Symposium on User Interface Software and Technology, pp. 27-29, 2017.
[10] B. L. Bonilla, H. H. Asada, “A robot on the shoulder: Coordinated human-wearable robot control using coloured petri nets and partial least squares predictions” IEEE International Conference on Robotics and Automation (ICRA). pp. 119-125, 2015.
[11] F. Parietti, H. H. Asada, “Dynamic analysis and state estimation for wearable robotic limbs subject to human-induced disturbances” IEEE International Conference on Robotics and Automation, pp. 3880-3887, 2013.
[12] V. Vatsal, G. Hoffman, “Design and Analysis of a Wearable Robotic Forearm” IEEE International Conference on Robotics and Automation (ICRA), pp. 1-8, 2018.
[13] P. H. Nguyen, C. Sparks, S. G. Nuthi, “Soft poly-limbs: Toward a new paradigm of mobile manipulation for daily living tasks” Soft robotics, Vol. 6, pp. 38–53, 2019.
[14] Y. F. Lu, D. P. Fan, D. J. Sheng, “Design consideration for precise cable drive” Advanced Materials Research, Vol. 305, pp. 37–41, 2011.
[15] Y. Chen, G Li, Y Zhu, “Design of a 6-DOF upper limb rehabilitation exoskeleton with parallel actuated joints” Bio-medical materials and engineering, Vol. 24, pp. 2527–2535, 2014.
[16] W. Wang, “Machine design handbook (New edition)” China Machine Press, Beijing, China,2004, Vol. 3, pp. 211–266.
[17] A. R. Tilley, “The measure of man and woman: human factors in design” John Wiley & Sons, 2001.
[18] M. H. Rahman, M. Saad, J. P. Kenné, “Modeling and control of a 7DOF exoskeleton robot for arm movements” IEEE International Conference on Robotics and Biomimetics (ROBIO), pp. 245-250, 2009.
[19] J. J. Craig, Introduction to robotics: mechanics and control, Pearson Education India, 2009, pp. 148–159.