Abstract: Proposing an appropriate control strategy is an effective and practical way to address the overheat problems of the wet multi-plate clutch in Direct Shift Gearbox under the long-time creeping condition. To do so, the temperature variation of the wet multi-plate clutch is investigated firstly by establishing a thermal resistance model for the gearbox cooling system. To calculate the generated heat flux and predict the clutch temperature precisely, the friction torque model is optimized by introducing an improved friction coefficient, which is related to the pressure, the relative speed and the temperature. After that, the heat transfer model and the reasonable friction torque model are employed by the vehicle powertrain model to construct a comprehensive co-simulation model for the Direct Shift Gearbox (DSG) vehicle. A creeping control strategy is then proposed and, to evaluate the vehicle performance, the safety temperature (250 ℃) is particularly adopted as an important metric. During the creeping process, the temperature of two clutches is always under the safety value (250 ℃), which demonstrates the effectiveness of the proposed control strategy in avoiding the thermal failures of clutches.
Abstract: A microcontroller-based fan coil unit (FCU) fuzzy controller is designed and implemented in this paper. The controller employs the concept of duty ratio on the electric valve control, which could make full use of the cooling and dehumidifying capacity of the FCU when the valve is off. The traditional control method and its limitations are analyzed. The hardware and software design processes are introduced in detail. The experimental results show that the proposed method is more energy efficient compared to the traditional controlling strategy. Furthermore, a more comfortable room condition could be achieved by the proposed method. The proposed low-cost FCU fuzzy controller deserves to be widely used in engineering applications.
Abstract: Performances analysis of remote sensing sensor is required to pursue a range of scientific research and application objectives. Laboratory analysis of any remote sensing instrument is essential, but not sufficient to establish a valid inflight one. In this study, with the aid of the in situ measurements and corresponding image of three-gray scale permanent artificial target, the in-flight radiometric performances analyses (in-flight radiometric calibration, dynamic range and response linearity, signal-noise-ratio (SNR), radiometric resolution) of self-developed short-wave infrared (SWIR) camera are performed. To acquire the inflight calibration coefficients of the SWIR camera, the at-sensor radiances (Li) for the artificial targets are firstly simulated with in situ measurements (atmosphere parameter and spectral reflectance of the target) and viewing geometries using MODTRAN model. With these radiances and the corresponding digital numbers (DN) in the image, a straight line with a formulation of L = G × DN + B is fitted by a minimization regression method, and the fitted coefficients, G and B, are inflight calibration coefficients. And then the high point (LH) and the low point (LL) of dynamic range can be described as LH= (G × DNH + B) and LL= B, respectively, where DNH is equal to 2n − 1 (n is the quantization number of the payload). Meanwhile, the sensor’s response linearity (δ) is described as the correlation coefficient of the regressed line. The results show that the calibration coefficients (G and B) are 0.0083 W·sr−1m−2µm−1 and −3.5 W·sr−1m−2µm−1; the low point of dynamic range is −3.5 W·sr−1m−2µm−1 and the high point is 30.5 W·sr−1m−2µm−1; the response linearity is approximately 99%. Furthermore, a SNR normalization method is used to assess the sensor’s SNR, and the normalized SNR is about 59.6 when the mean value of radiance is equal to 11.0 W·sr−1m−2µm−1; subsequently, the radiometric resolution is calculated about 0.1845 W•sr-1m-2μm-1. Moreover, in order to validate the result, a comparison of the measured radiance with a radiative-transfer-code-predicted over four portable artificial targets with reflectance of 20%, 30%, 40%, 50% respectively, is performed. It is noted that relative error for the calibration is within 6.6%.
Abstract: This paper presents the development of a Bayesian
belief network classifier for prediction of graft status and survival
period in renal transplantation using the patient profile information
prior to the transplantation. The objective was to explore feasibility
of developing a decision making tool for identifying the most suitable
recipient among the candidate pool members. The dataset was
compiled from the University of Toledo Medical Center Hospital
patients as reported to the United Network Organ Sharing, and had
1228 patient records for the period covering 1987 through 2009. The
Bayes net classifiers were developed using the Weka machine
learning software workbench. Two separate classifiers were induced
from the data set, one to predict the status of the graft as either failed
or living, and a second classifier to predict the graft survival period.
The classifier for graft status prediction performed very well with a
prediction accuracy of 97.8% and true positive values of 0.967 and
0.988 for the living and failed classes, respectively. The second
classifier to predict the graft survival period yielded a prediction
accuracy of 68.2% and a true positive rate of 0.85 for the class
representing those instances with kidneys failing during the first year
following transplantation. Simulation results indicated that it is
feasible to develop a successful Bayesian belief network classifier for
prediction of graft status, but not the graft survival period, using the
information in UNOS database.
Abstract: This study investigates a voltage-controllable liquid crystals lens with a Fresnel zone electrode. When applying a proper voltage on the liquid crystal cell, a Fresnel-zone-distributed electric field is induced to direct liquid crystals aligned in a concentric structure. Owing to the concentrically aligned liquid crystals, a Fresnel lens is formed. We probe the Fresnel liquid crystal lens using a polarized incident beam with a wavelength of 632.8 nm, finding that the diffraction efficiency depends on the applying voltage. A remarkable diffraction efficiency of ~39.5 % is measured at the voltage of 0.9V. Additionally, a dual focus lens is fabricated by attaching a plane-convex lens to the Fresnel liquid crystals cell. The Fresnel LC lens and the dual focus lens may be applied for DVD/CD pick-up head, confocal microscopy system, or electrically-controlling optical systems.
Abstract: Studies in neuroscience suggest that both global and
local feature information are crucial for perception and recognition of
faces. It is widely believed that local feature is less sensitive to
variations caused by illumination, expression and illumination. In
this paper, we target at designing and learning local features for face
recognition. We designed three types of local features. They are
semi-global feature, local patch feature and tangent shape feature.
The designing of semi-global feature aims at taking advantage of
global-like feature and meanwhile avoiding suppressing AdaBoost
algorithm in boosting weak classifies established from small local
patches. The designing of local patch feature targets at automatically
selecting discriminative features, and is thus different with traditional
ways, in which local patches are usually selected manually to cover
the salient facial components. Also, shape feature is considered in
this paper for frontal view face recognition. These features are
selected and combined under the framework of boosting algorithm
and cascade structure. The experimental results demonstrate that the
proposed approach outperforms the standard eigenface method and
Bayesian method. Moreover, the selected local features and
observations in the experiments are enlightening to researches in
local feature design in face recognition.