Abstract: There is a need for new systems that can be attached to drinking water treatment plants and have the required treatment capacity as well as the selectivity regarding components derived from anthropogenic activities. In a context of high volumes of water and low concentration of contaminants, adsorption/interchange processes are appealing since they meet the required features. Iron oxides such as siderite and molysite, which are respectively based on FeCO3 and FeCl3, can be found in nature. In this work, their observed performance, raw or roasted at different temperatures, as adsorbents of some inorganic anions is discussed. Roasted 1:1 FeCO3: FeCl3 mixture was very selective for arsenic and allowed a 100% removal of As from a 10 mg L-1 As solution. Besides, the 1:1 FeCO3 and FeCl3 mixture roasted at 500 ºC showed good selectivity for, in order of preference, arsenate, bromate, phosphate, fluoride and nitrate anions with distribution coefficients of, respectively, 4200, 2800, 2500 0.4 and 0.03 L g-1.
Abstract: A kinetic façade responds to user requirements and environmental conditions. In designing a kinetic façade, kinetic patterns play a key role in determining its performance. This paper proposes a biomimetic method for the multi-objective optimization for kinetic façade design. The autonomous decentralized control system is combined with flocking algorithm. The flocking agents are autonomously reacting to sensor values and bring about kinetic patterns changing over time. A series of experiments were conducted to verify the potential and limitations of the flocking based decentralized control. As a result, it could show the highest performance balancing multiple objectives such as solar radiation and openness among the comparison group.
Abstract: The Intelligent transportation system is essential to build smarter cities. Machine learning based transportation prediction could be highly promising approach by delivering invisible aspect visible. In this context, this research aims to make a prototype model that predicts transportation network by using big data and machine learning technology. In detail, among urban transportation systems this research chooses bus system. The research problem that existing headway model cannot response dynamic transportation conditions. Thus, bus delay problem is often occurred. To overcome this problem, a prediction model is presented to fine patterns of bus delay by using a machine learning implementing the following data sets; traffics, weathers, and bus statues. This research presents a flexible headway model to predict bus delay and analyze the result. The prototyping model is composed by real-time data of buses. The data are gathered through public data portals and real time Application Program Interface (API) by the government. These data are fundamental resources to organize interval pattern models of bus operations as traffic environment factors (road speeds, station conditions, weathers, and bus information of operating in real-time). The prototyping model is designed by the machine learning tool (RapidMiner Studio) and conducted tests for bus delays prediction. This research presents experiments to increase prediction accuracy for bus headway by analyzing the urban big data. The big data analysis is important to predict the future and to find correlations by processing huge amount of data. Therefore, based on the analysis method, this research represents an effective use of the machine learning and urban big data to understand urban dynamics.
Abstract: A survey of small-size contractors in Jeju was conducted to investigate college graduate's computer-aided design (CAD) competence. Most of small-size contractors use CAD software to review and update drawings submitted from an architect. This research analyzed the curriculum of the architectural engineering in several national universities. The CAD classes have 4 or 6 hours per week and use AutoCAD primarily. This paper proposes that a CAD class needs 6 hours per week, 2D drawing is the main theme in the curriculum, and exercises to make 3D models are also included in the CAD class. An improved method, for example Internet cafe and real time feedbacks using smartphones, to evaluate the reports and exercise results is necessary.
Abstract: This study investigated the effects of the dietary supplementation of the Allium hookeri root, and processed sulfur, on the growth performance of guinea pigs. The guinea pigs were fed a control diet (CON), as well as the control diet including 1% freeze-dried Allium hookeri root (AH), or 0.1% processed sulfur (S), or including both the freeze-dried Allium hookeri root and the processed sulfur (AHS). The weight of perirenal adipose tissue (PAT) and the epididymal adipose tissue (EAT) in the AH were significantly lower than CON (p < 0.05). The serum cholesterols levels of the AH and the AHS were significantly lower than the S (p < 0.05). While the total saturated fatty acid content in the serum of the AH and AHS groups showed a tendency to decrease, the total monounsaturated fatty acid increased. The results of this study suggested that dietary consumption of Allium hookeri root may help to decrease fat accumulation, lower serum cholesterol levels, and control serum free fatty acid contents in the guinea pigs.
Abstract: The purpose of this study is to examine the research trends of life-long education for people with disabilities using a keyword network analysis. For this purpose, 151 papers were selected from 594 papers retrieved using keywords such as 'people with disabilities' and 'life-long education' in the Korean Education and Research Information Service. The Keyword network analysis was constructed by extracting and coding the keyword used in the title of the selected papers. The frequency of the extracted keywords, the centrality of degree, and betweenness was analyzed by the keyword network. The results of the keyword network analysis are as follows. First, the main keywords that appeared frequently in the study of life-long education for people with disabilities were 'people with disabilities', 'life-long education', 'developmental disabilities', 'current situations', 'development'. The research trends of life-long education for people with disabilities are focused on the current status of the life-long education and the program development. Second, the keyword network analysis and visualization showed that the keywords with high frequency of occurrences also generally have high degree centrality and betweenness centrality. In terms of the keyword network diagram, it was confirmed that research trends of life-long education for people with disabilities are centered on six prominent keywords. Based on these results, it was discussed that life-long education for people with disabilities in the future needs to expand the subjects and the supporting areas of the life-long education, and the research needs to be further expanded into more detailed and specific areas.
Abstract: Current real-estate value estimation, difficult for laymen, usually is performed by specialists. This paper presents an automated estimation process based on big data and machine-learning technology that calculates influences of building conditions on real-estate price measurement. The present study analyzed actual building sales sample data for Nonhyeon-dong, Gangnam-gu, Seoul, Korea, measuring the major influencing factors among the various building conditions. Further to that analysis, a prediction model was established and applied using RapidMiner Studio, a graphical user interface (GUI)-based tool for derivation of machine-learning prototypes. The prediction model is formulated by reference to previous examples. When new examples are applied, it analyses and predicts accordingly. The analysis process discerns the crucial factors effecting price increases by calculation of weighted values. The model was verified, and its accuracy determined, by comparing its predicted values with actual price increases.
Abstract: In designing a kinetic façade, it is hard for the designer to make digital models due to its complex geometry with motion. This paper aims to present a methodology of converting a point cloud of a physical model into a single digital model with a certain topology and motion. The method uses a Microsoft Kinect sensor, and color markers were defined and applied to three paper folding-inspired designs. Although the resulted digital model cannot represent the whole folding range of the physical model, the method supports the designer to conduct a performance-oriented design process with the rough physical model in the reduced folding range.
Abstract: As Korea government has expanded the budget for the
national research and development business, the need for the
installation of institute taking a role of deliberation, coordination, and
operation of research development business and its budget has been
increased continuously. In response to the demands of the times,
recently, the National Science & Technology Council (NSTC) was
installed. However, to achieve a creative economy more efficiently,
the fundamental introspection on the current state of the national
administration system of science and technology in Korea should be
needed. Accordingly, this study, firstly, analyzes the function and
organizational structure of NSTC in Korea. Then, this study
investigates the current state of the National Science and Technology
Council in main world countries. Lastly, this study derives some
implications based on the comparison analysis of the current state of
the National Science and Technology Council between Korea and
these countries. The present study will help in finding the way for the
advancement of the NSTC in Korea.
Abstract: The performances of nuclear fuels and materials are qualified at an irradiation system in research reactors operating under the commercial nuclear power plant conditions. Fuel centerline temperature, coolant temperature, neutron flux, deformations of fuel stack and swelling are important parameters needed to analyze the nuclear fuel performances. The dimensional stability of nuclear fuels is a key parameter measuring the fuel densification and swelling. In this study, the fuel stack elongation is measured using a LVDT. A mockup LVDT instrumented fuel rod is developed. The performances of mockup LVDT instrumented fuel rod is evaluated by experiments.
Abstract: The objective of this research is to develop a general technique so that one may predict the dynamic behaviour of a three-dimensional scale crane model subjected to time-dependent moving point forces by means of conventional finite element computer packages. To this end, the whole scale crane model is divided into two parts: the stationary framework and the moving substructure. In such a case, the dynamic responses of a scale crane model can be predicted from the forced vibration responses of the stationary framework due to actions of the four time-dependent moving point forces induced by the moving substructure. Since the magnitudes and positions of the moving point forces are dependent on the relative positions between the trolley, moving substructure and the stationary framework, it can be found from the numerical results that the time histories for the moving speeds of the moving substructure and the trolley are the key factors affecting the dynamic responses of the scale crane model.
Abstract: Earth structures constructed of marine clay soils have
tendency to crack. In order to improve the flexural strength and
brittleness, a technique of mixing short fibers is introduced to the soil
lime mixture. Coir fiber was used in this study as reinforcing
elements. An experimental investigation consisting primarily of
flexural tensile tests was conducted to examine the influence of coir
fibers on the flexural behaviour of the reinforced soils. The test
results that the coir fibers were effective in improving the flexural
strength and Young’s modulus of all soils examined and ductility
after peak strength for reinforced marine clay soil treated by lime. 5%
lime treated soil and 1% coir fiber reinforced soil specimens’
demonstrated good strength and durability when submerged in water
and retained 45% of their air-cured strengths.
Abstract: Since the advances in digital imaging technologies have led to
development of high quality digital devices, there are a lot of illegal copies
of copyrighted video content on the Internet. Also, unauthorized editing is
occurred frequently. Thus, we propose an editing prevention technique for
high-quality (HQ) video that can prevent these illegally edited copies from
spreading out. The proposed technique is applied spatial and temporal gradient
methods to improve the fidelity and detection performance. Also, the scheme
duplicates the embedding signal temporally to alleviate the signal reduction
caused by geometric and signal-processing distortions. Experimental results
show that the proposed scheme achieves better performance than previously
proposed schemes and it has high fidelity. The proposed scheme can be used
in unauthorized access prevention method of visual communication or traitor
tracking applications which need fast detection process to prevent illegally
edited video content from spreading out.
Abstract: The reheating furnace is used to reheat the steel slabs
before the hot-rolling process. The supported system includes the
stationary/moving beams, and the skid buttons which block some
thermal radiation transmitted to the bottom of the slabs. Therefore, it is
important to analyze the steel slab temperature distribution during the
heating period. A three-dimensional mathematical transient heat
transfer model for the prediction of temperature distribution within the
slab has been developed. The effects of different skid button height
(H=60mm, 90mm, and 120mm) and different gap distance between
two slabs (S=50mm, 75mm, and 100mm) on the slab skid mark
formation and temperature profiles are investigated. Comparison with
the in-situ experimental data from Steel Company in Taiwan shows
that the present heat transfer model works well for the prediction of
thermal behavior of the slab in the reheating furnace. It is found that
the skid mark severity decreases with an increase in the skid button
height. The effect of gap distance is important only for the slab edge
planes, while it is insignificant for the slab central planes.
Abstract: This study was carried out for an underground subway station at Seoul Metro, Korea. The optimal set-points of the ventilation control system are determined every 3 hours, then, the ventilation controller adjusts the ventilation fan speed according to the optimal set-point changes. Compared to manual ventilation system which is operated irrespective of the OAQ, the IDP-based ventilation control system saves 3.7% of the energy consumption. Compared to the fixed set-point controller which is operated irrespective of the IAQ diurnal variation, the IDP-based controller shows better performance with a 2% decrease in energy consumption, maintaining the comfortable IAQ range inside the station.
Abstract: This study aims to evaluate the effective size, section
and structural characteristics of circular hollow steel (CHS) damper.
CHS damper is among steel dampers which are used widely for
seismic energy dissipation because they are easy to install, maintain
and are inexpensive. CHS damper dissipates seismic energy through
metallic deformation due to the geometrical elasticity of circular shape
and fatigue resistance around connection part. After calculating the
effective size, which is found to be height to diameter ratio of √3,
nonlinear FE analyses were carried out to evaluate the structural
characteristics and effective section (diameter-to-ratio).
Abstract: A three-dimensional numerical model of
thermoelectric generator (TEG) modules attached to a large chimney
plate is proposed and solved numerically using a control volume based
finite difference formulation. The TEG module consists of a
thermoelectric generator, an elliptical pin-fin heat sink, and a cold
plate for water cooling. In the chimney, the temperature of flue gases is
450-650K. Although the TEG hot-side temperature and thus the
electric power output can be increased by inserting an elliptical pin-fin
heat sink into the chimney tunnel to increase the heat transfer area, the
pin fin heat sink would cause extra pumping power at the same time.
The main purpose of this study is to analyze the effects of geometrical
parameters on the electric power output and chimney pressure drop
characteristics. The effects of different operating conditions, including
various inlet velocities (Vin= 1, 3, 5 m/s), inlet temperatures (Tgas = 450,
550, 650K) and different fin height (0 to 150 mm) are discussed in
detail. The predicted numerical data for the power vs. current (P-I)
curve are in good agreement (within 11%) with the experimental data.
Abstract: This paper presents the scaling laws that provide the
criteria of geometry and dynamic similitude between the full-size
rotor-shaft system and its scale model, and can be used to predict the
torsional vibration characteristics of the full-size rotor-shaft system by
manipulating the corresponding data of its scale model. The scaling
factors, which play fundamental roles in predicting the geometry and
dynamic relationships between the full-size rotor-shaft system and its
scale model, for torsional free vibration problems between scale and
full-size rotor-shaft systems are firstly obtained from the equation of
motion of torsional free vibration. Then, the scaling factor of external
force (i.e., torque) required for the torsional forced vibration problems
is determined based on the Newton’s second law. Numerical results
show that the torsional free and forced vibration characteristics of a
full-size rotor-shaft system can be accurately predicted from those of
its scale models by using the foregoing scaling factors. For this reason,
it is believed that the presented approach will be significant for
investigating the relevant phenomenon in the scale model tests.
Abstract: This study applies the inverse method and three- dimensional CFD commercial software in conjunction with the experimental temperature data to investigate the heat transfer and fluid flow characteristics of the plate-fin heat sink in a closed rectangular enclosure for various values of fin height. The inverse method with the finite difference method and the experimental temperature data is applied to determine the heat transfer coefficient. The k-ε turbulence model is used to obtain the heat transfer and fluid flow characteristics within the fins. To validate the accuracy of the results obtained, the comparison of the average heat transfer coefficient is made. The calculated temperature at selected measurement locations on the plate-fin is also compared with experimental data.
Abstract: The objective of the paper is to measure and compare market orientation of Swiss and Czech banks, as well as examine statistically the degree of influence it has on competitiveness of the institutions. The analysis of market orientation is based on the collecting, analysis and correct interpretation of the data. Descriptive analysis of market orientation describe current situation. Research of relation of competitiveness and market orientation in the sector of big international banks is suggested with the expectation of existence of a strong relationship. Partially, the work served as reconfirmation of suitability of classic methodologies to measurement of banks’ market orientation.
Two types of data were gathered. Firstly, by measuring subjectively perceived market orientation of a company and secondly, by quantifying its competitiveness. All data were collected from a sample of small, mid-sized and large banks. We used numerical secondary character data from the international statistical financial Bureau Van Dijk’s BANKSCOPE database.
Statistical analysis led to the following results. Assuming classical market orientation measures to be scientifically justified, Czech banks are statistically less market-oriented than Swiss banks. Secondly, among small Swiss banks, which are not broadly internationally active, small relationship exist between market orientation measures and market share based competitiveness measures. Thirdly, among all Swiss banks, a strong relationship exists between market orientation measures and market share based competitiveness measures. Above results imply existence of a strong relation of this measure in sector of big international banks. A strong statistical relationship has been proven to exist between market orientation measures and equity/total assets ratio in Switzerland.